forked from Minki/linux
03daa99ef5
Add compatible "fsl,mpic-msi-v4.3" for MPIC v4.3. MPIC v4.3 contains MSIIR and MSIIR1. MSIIR supports 8 MSI registers and MSIIR1 supports 16 MSI registers, but uses different IBS and SRS shift. When using MSIR1, the interrupt number is not consecutive. It is hard to use 'msi-available-ranges' to describe the ranges of the available interrupt, so MPIC v4.3 does not support this property. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> [scottwood@freescale.com: minor grammar fixes] Signed-off-by: Scott Wood <scottwood@freescale.com>
117 lines
4.6 KiB
Plaintext
117 lines
4.6 KiB
Plaintext
* Freescale MSI interrupt controller
|
|
|
|
Required properties:
|
|
- compatible : compatible list, may contain one or two entries
|
|
The first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572,
|
|
etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" or
|
|
"fsl,mpic-msi-v4.3" depending on the parent type and version. If mpic
|
|
version is 4.3, the number of MSI registers is increased to 16, MSIIR1 is
|
|
provided to access these 16 registers, and compatible "fsl,mpic-msi-v4.3"
|
|
should be used. The first entry is optional; the second entry is
|
|
required.
|
|
|
|
- reg : It may contain one or two regions. The first region should contain
|
|
the address and the length of the shared message interrupt register set.
|
|
The second region should contain the address of aliased MSIIR or MSIIR1
|
|
register for platforms that have such an alias, if using MSIIR1, the second
|
|
region must be added because different MSI group has different MSIIR1 offset.
|
|
|
|
- interrupts : each one of the interrupts here is one entry per 32 MSIs,
|
|
and routed to the host interrupt controller. the interrupts should
|
|
be set as edge sensitive. If msi-available-ranges is present, only
|
|
the interrupts that correspond to available ranges shall be present.
|
|
|
|
- interrupt-parent: the phandle for the interrupt controller
|
|
that services interrupts for this device. for 83xx cpu, the interrupts
|
|
are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed
|
|
to MPIC.
|
|
|
|
Optional properties:
|
|
- msi-available-ranges: use <start count> style section to define which
|
|
msi interrupt can be used in the 256 msi interrupts. This property is
|
|
optional, without this, all the MSI interrupts can be used.
|
|
Each available range must begin and end on a multiple of 32 (i.e.
|
|
no splitting an individual MSI register or the associated PIC interrupt).
|
|
MPIC v4.3 does not support this property because the 32 interrupts of an
|
|
individual register are not continuous when using MSIIR1.
|
|
|
|
- msi-address-64: 64-bit PCI address of the MSIIR register. The MSIIR register
|
|
is used for MSI messaging. The address of MSIIR in PCI address space is
|
|
the MSI message address.
|
|
|
|
This property may be used in virtualized environments where the hypervisor
|
|
has created an alternate mapping for the MSIR block. See below for an
|
|
explanation.
|
|
|
|
|
|
Example:
|
|
msi@41600 {
|
|
compatible = "fsl,mpc8610-msi", "fsl,mpic-msi";
|
|
reg = <0x41600 0x80>;
|
|
msi-available-ranges = <0 0x100>;
|
|
interrupts = <
|
|
0xe0 0
|
|
0xe1 0
|
|
0xe2 0
|
|
0xe3 0
|
|
0xe4 0
|
|
0xe5 0
|
|
0xe6 0
|
|
0xe7 0>;
|
|
interrupt-parent = <&mpic>;
|
|
};
|
|
|
|
msi@41600 {
|
|
compatible = "fsl,mpic-msi-v4.3";
|
|
reg = <0x41600 0x200 0x44148 4>;
|
|
interrupts = <
|
|
0xe0 0 0 0
|
|
0xe1 0 0 0
|
|
0xe2 0 0 0
|
|
0xe3 0 0 0
|
|
0xe4 0 0 0
|
|
0xe5 0 0 0
|
|
0xe6 0 0 0
|
|
0xe7 0 0 0
|
|
0x100 0 0 0
|
|
0x101 0 0 0
|
|
0x102 0 0 0
|
|
0x103 0 0 0
|
|
0x104 0 0 0
|
|
0x105 0 0 0
|
|
0x106 0 0 0
|
|
0x107 0 0 0>;
|
|
};
|
|
|
|
The Freescale hypervisor and msi-address-64
|
|
-------------------------------------------
|
|
Normally, PCI devices have access to all of CCSR via an ATMU mapping. The
|
|
Freescale MSI driver calculates the address of MSIIR (in the MSI register
|
|
block) and sets that address as the MSI message address.
|
|
|
|
In a virtualized environment, the hypervisor may need to create an IOMMU
|
|
mapping for MSIIR. The Freescale ePAPR hypervisor has this requirement
|
|
because of hardware limitations of the Peripheral Access Management Unit
|
|
(PAMU), which is currently the only IOMMU that the hypervisor supports.
|
|
The ATMU is programmed with the guest physical address, and the PAMU
|
|
intercepts transactions and reroutes them to the true physical address.
|
|
|
|
In the PAMU, each PCI controller is given only one primary window. The
|
|
PAMU restricts DMA operations so that they can only occur within a window.
|
|
Because PCI devices must be able to DMA to memory, the primary window must
|
|
be used to cover all of the guest's memory space.
|
|
|
|
PAMU primary windows can be divided into 256 subwindows, and each
|
|
subwindow can have its own address mapping ("guest physical" to "true
|
|
physical"). However, each subwindow has to have the same alignment, which
|
|
means they cannot be located at just any address. Because of these
|
|
restrictions, it is usually impossible to create a 4KB subwindow that
|
|
covers MSIIR where it's normally located.
|
|
|
|
Therefore, the hypervisor has to create a subwindow inside the same
|
|
primary window used for memory, but mapped to the MSIR block (where MSIIR
|
|
lives). The first subwindow after the end of guest memory is used for
|
|
this. The address specified in the msi-address-64 property is the PCI
|
|
address of MSIIR. The hypervisor configures the PAMU to map that address to
|
|
the true physical address of MSIIR.
|