forked from Minki/linux
c0e6841653
Add device tree bindings for the NAND/External Memory Controller (NEMC) on Ingenic JZ4780 Signed-off-by: Alex Smith <alex@alex-smith.me.uk> Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
76 lines
2.4 KiB
Plaintext
76 lines
2.4 KiB
Plaintext
* Ingenic JZ4780 NAND/external memory controller (NEMC)
|
|
|
|
This file documents the device tree bindings for the NEMC external memory
|
|
controller in Ingenic JZ4780
|
|
|
|
Required properties:
|
|
- compatible: Should be set to one of:
|
|
"ingenic,jz4780-nemc" (JZ4780)
|
|
- reg: Should specify the NEMC controller registers location and length.
|
|
- clocks: Clock for the NEMC controller.
|
|
- #address-cells: Must be set to 2.
|
|
- #size-cells: Must be set to 1.
|
|
- ranges: A set of ranges for each bank describing the physical memory layout.
|
|
Each should specify the following 4 integer values:
|
|
|
|
<cs number> 0 <physical address of mapping> <size of mapping>
|
|
|
|
Each child of the NEMC node describes a device connected to the NEMC.
|
|
|
|
Required child node properties:
|
|
- reg: Should contain at least one register specifier, given in the following
|
|
format:
|
|
|
|
<cs number> <offset> <size>
|
|
|
|
Multiple registers can be specified across multiple banks. This is needed,
|
|
for example, for packaged NAND devices with multiple dies. Such devices
|
|
should be grouped into a single node.
|
|
|
|
Optional child node properties:
|
|
- ingenic,nemc-bus-width: Specifies the bus width in bits. Defaults to 8 bits.
|
|
- ingenic,nemc-tAS: Address setup time in nanoseconds.
|
|
- ingenic,nemc-tAH: Address hold time in nanoseconds.
|
|
- ingenic,nemc-tBP: Burst pitch time in nanoseconds.
|
|
- ingenic,nemc-tAW: Access wait time in nanoseconds.
|
|
- ingenic,nemc-tSTRV: Static memory recovery time in nanoseconds.
|
|
|
|
If a child node references multiple banks in its "reg" property, the same value
|
|
for all optional parameters will be configured for all banks. If any optional
|
|
parameters are omitted, they will be left unchanged from whatever they are
|
|
configured to when the NEMC device is probed (which may be the reset value as
|
|
given in the hardware reference manual, or a value configured by the boot
|
|
loader).
|
|
|
|
Example (NEMC node with a NAND child device attached at CS1):
|
|
|
|
nemc: nemc@13410000 {
|
|
compatible = "ingenic,jz4780-nemc";
|
|
reg = <0x13410000 0x10000>;
|
|
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
|
|
ranges = <1 0 0x1b000000 0x1000000
|
|
2 0 0x1a000000 0x1000000
|
|
3 0 0x19000000 0x1000000
|
|
4 0 0x18000000 0x1000000
|
|
5 0 0x17000000 0x1000000
|
|
6 0 0x16000000 0x1000000>;
|
|
|
|
clocks = <&cgu JZ4780_CLK_NEMC>;
|
|
|
|
nand: nand@1 {
|
|
compatible = "ingenic,jz4780-nand";
|
|
reg = <1 0 0x1000000>;
|
|
|
|
ingenic,nemc-tAS = <10>;
|
|
ingenic,nemc-tAH = <5>;
|
|
ingenic,nemc-tBP = <10>;
|
|
ingenic,nemc-tAW = <15>;
|
|
ingenic,nemc-tSTRV = <100>;
|
|
|
|
...
|
|
};
|
|
};
|