linux/arch/sh/drivers/pci/fixups-se7751.c
Matthew Minter 2b8ff9f276 sh/PCI: Remove __init optimisations from IRQ mapping functions/data
Currently many IRQ mapping functions and data structures use the __init and
__initdata optimisations. These result in the relevant functions being
innaccessible after boot time.

However for deferred IRQ assignment it is important to have access to these
functions at PCI device enable time.

Therefore, remove the optimisation from the relevant data structures and
functions to prepare for deferred IRQ assignment.

Signed-off-by: Matthew Minter <matt@masarand.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
2017-08-03 16:21:31 -05:00

113 lines
4.1 KiB
C

#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/pci.h>
#include <linux/io.h>
#include <linux/sh_intc.h>
#include "pci-sh4.h"
int pcibios_map_platform_irq(const struct pci_dev *, u8 slot, u8 pin)
{
switch (slot) {
case 0: return evt2irq(0x3a0);
case 1: return evt2irq(0x3a0); /* AMD Ethernet controller */
case 2: return -1;
case 3: return -1;
case 4: return -1;
default:
printk("PCI: Bad IRQ mapping request for slot %d\n", slot);
return -1;
}
}
#define PCIMCR_MRSET_OFF 0xBFFFFFFF
#define PCIMCR_RFSH_OFF 0xFFFFFFFB
/*
* Only long word accesses of the PCIC's internal local registers and the
* configuration registers from the CPU is supported.
*/
#define PCIC_WRITE(x,v) writel((v), PCI_REG(x))
#define PCIC_READ(x) readl(PCI_REG(x))
/*
* Description: This function sets up and initializes the pcic, sets
* up the BARS, maps the DRAM into the address space etc, etc.
*/
int pci_fixup_pcic(struct pci_channel *chan)
{
unsigned long bcr1, wcr1, wcr2, wcr3, mcr;
unsigned short bcr2;
/*
* Initialize the slave bus controller on the pcic. The values used
* here should not be hardcoded, but they should be taken from the bsc
* on the processor, to make this function as generic as possible.
* (i.e. Another sbc may usr different SDRAM timing settings -- in order
* for the pcic to work, its settings need to be exactly the same.)
*/
bcr1 = (*(volatile unsigned long*)(SH7751_BCR1));
bcr2 = (*(volatile unsigned short*)(SH7751_BCR2));
wcr1 = (*(volatile unsigned long*)(SH7751_WCR1));
wcr2 = (*(volatile unsigned long*)(SH7751_WCR2));
wcr3 = (*(volatile unsigned long*)(SH7751_WCR3));
mcr = (*(volatile unsigned long*)(SH7751_MCR));
bcr1 = bcr1 | 0x00080000; /* Enable Bit 19, BREQEN */
(*(volatile unsigned long*)(SH7751_BCR1)) = bcr1;
bcr1 = bcr1 | 0x40080000; /* Enable Bit 19 BREQEN, set PCIC to slave */
PCIC_WRITE(SH7751_PCIBCR1, bcr1); /* PCIC BCR1 */
PCIC_WRITE(SH7751_PCIBCR2, bcr2); /* PCIC BCR2 */
PCIC_WRITE(SH7751_PCIWCR1, wcr1); /* PCIC WCR1 */
PCIC_WRITE(SH7751_PCIWCR2, wcr2); /* PCIC WCR2 */
PCIC_WRITE(SH7751_PCIWCR3, wcr3); /* PCIC WCR3 */
mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF;
PCIC_WRITE(SH7751_PCIMCR, mcr); /* PCIC MCR */
/* Enable all interrupts, so we know what to fix */
PCIC_WRITE(SH7751_PCIINTM, 0x0000c3ff);
PCIC_WRITE(SH7751_PCIAINTM, 0x0000380f);
/* Set up standard PCI config registers */
PCIC_WRITE(SH7751_PCICONF1, 0xF39000C7); /* Bus Master, Mem & I/O access */
PCIC_WRITE(SH7751_PCICONF2, 0x00000000); /* PCI Class code & Revision ID */
PCIC_WRITE(SH7751_PCICONF4, 0xab000001); /* PCI I/O address (local regs) */
PCIC_WRITE(SH7751_PCICONF5, 0x0c000000); /* PCI MEM address (local RAM) */
PCIC_WRITE(SH7751_PCICONF6, 0xd0000000); /* PCI MEM address (unused) */
PCIC_WRITE(SH7751_PCICONF11, 0x35051054); /* PCI Subsystem ID & Vendor ID */
PCIC_WRITE(SH7751_PCILSR0, 0x03f00000); /* MEM (full 64M exposed) */
PCIC_WRITE(SH7751_PCILSR1, 0x00000000); /* MEM (unused) */
PCIC_WRITE(SH7751_PCILAR0, 0x0c000000); /* MEM (direct map from PCI) */
PCIC_WRITE(SH7751_PCILAR1, 0x00000000); /* MEM (unused) */
/* Now turn it on... */
PCIC_WRITE(SH7751_PCICR, 0xa5000001);
/*
* Set PCIMBR and PCIIOBR here, assuming a single window
* (16M MEM, 256K IO) is enough. If a larger space is
* needed, the readx/writex and inx/outx functions will
* have to do more (e.g. setting registers for each call).
*/
/*
* Set the MBR so PCI address is one-to-one with window,
* meaning all calls go straight through... use BUG_ON to
* catch erroneous assumption.
*/
BUG_ON(chan->resources[1].start != SH7751_PCI_MEMORY_BASE);
PCIC_WRITE(SH7751_PCIMBR, chan->resources[1].start);
/* Set IOBR for window containing area specified in pci.h */
PCIC_WRITE(SH7751_PCIIOBR, (chan->resources[0].start & SH7751_PCIIOBR_MASK));
/* All done, may as well say so... */
printk("SH7751 PCI: Finished initialization of the PCI controller\n");
return 1;
}