forked from Minki/linux
f604931238
Additional cleanup for debug boards on H2/P2/H3/H4: move the init code that's not board-specific into a new file where it can be easily shared between all the different boards (avoiding code duplication, and making it easier to support more devices). Make H4 use that. This should be easy to drop in to the OMAP1 boards using these debug cards; the only difference seems to be that the p2 does an extra reset of the smc using the fpga (probably all boards could do that, if it's necessary) and doesn't use the gpio mux or request APIs. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
145 lines
3.5 KiB
Plaintext
145 lines
3.5 KiB
Plaintext
if ARCH_OMAP
|
|
|
|
menu "TI OMAP Implementations"
|
|
|
|
config ARCH_OMAP_OTG
|
|
bool
|
|
|
|
choice
|
|
prompt "OMAP System Type"
|
|
default ARCH_OMAP1
|
|
|
|
config ARCH_OMAP1
|
|
bool "TI OMAP1"
|
|
select GENERIC_CLOCKEVENTS
|
|
|
|
config ARCH_OMAP2
|
|
bool "TI OMAP2"
|
|
|
|
endchoice
|
|
|
|
comment "OMAP Feature Selections"
|
|
|
|
config OMAP_DEBUG_DEVICES
|
|
bool
|
|
help
|
|
For debug cards on TI reference boards.
|
|
|
|
config OMAP_DEBUG_LEDS
|
|
bool
|
|
depends on OMAP_DEBUG_DEVICES
|
|
default y if LEDS || LEDS_OMAP_DEBUG
|
|
|
|
config OMAP_RESET_CLOCKS
|
|
bool "Reset unused clocks during boot"
|
|
depends on ARCH_OMAP
|
|
help
|
|
Say Y if you want to reset unused clocks during boot.
|
|
This option saves power, but assumes all drivers are
|
|
using the clock framework. Broken drivers that do not
|
|
yet use clock framework may not work with this option.
|
|
If you are booting from another operating system, you
|
|
probably do not want this option enabled until your
|
|
device drivers work properly.
|
|
|
|
config OMAP_MUX
|
|
bool "OMAP multiplexing support"
|
|
depends on ARCH_OMAP
|
|
default y
|
|
help
|
|
Pin multiplexing support for OMAP boards. If your bootloader
|
|
sets the multiplexing correctly, say N. Otherwise, or if unsure,
|
|
say Y.
|
|
|
|
config OMAP_MUX_DEBUG
|
|
bool "Multiplexing debug output"
|
|
depends on OMAP_MUX
|
|
help
|
|
Makes the multiplexing functions print out a lot of debug info.
|
|
This is useful if you want to find out the correct values of the
|
|
multiplexing registers.
|
|
|
|
config OMAP_MUX_WARNINGS
|
|
bool "Warn about pins the bootloader didn't set up"
|
|
depends on OMAP_MUX
|
|
default y
|
|
help
|
|
Choose Y here to warn whenever driver initialization logic needs
|
|
to change the pin multiplexing setup. When there are no warnings
|
|
printed, it's safe to deselect OMAP_MUX for your product.
|
|
|
|
config OMAP_MCBSP
|
|
bool "McBSP support"
|
|
depends on ARCH_OMAP
|
|
default y
|
|
help
|
|
Say Y here if you want support for the OMAP Multichannel
|
|
Buffered Serial Port.
|
|
|
|
choice
|
|
prompt "System timer"
|
|
default OMAP_MPU_TIMER
|
|
|
|
config OMAP_MPU_TIMER
|
|
bool "Use mpu timer"
|
|
help
|
|
Select this option if you want to use the OMAP mpu timer. This
|
|
timer provides more intra-tick resolution than the 32KHz timer,
|
|
but consumes more power.
|
|
|
|
config OMAP_32K_TIMER
|
|
bool "Use 32KHz timer"
|
|
depends on ARCH_OMAP16XX || ARCH_OMAP24XX
|
|
help
|
|
Select this option if you want to enable the OMAP 32KHz timer.
|
|
This timer saves power compared to the OMAP_MPU_TIMER, and has
|
|
support for no tick during idle. The 32KHz timer provides less
|
|
intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is
|
|
currently only available for OMAP16XX and 24XX.
|
|
|
|
endchoice
|
|
|
|
config OMAP_32K_TIMER_HZ
|
|
int "Kernel internal timer frequency for 32KHz timer"
|
|
range 32 1024
|
|
depends on OMAP_32K_TIMER
|
|
default "128"
|
|
help
|
|
Kernel internal timer frequency should be a divisor of 32768,
|
|
such as 64 or 128.
|
|
|
|
config OMAP_DM_TIMER
|
|
bool "Use dual-mode timer"
|
|
depends on ARCH_OMAP16XX || ARCH_OMAP24XX
|
|
help
|
|
Select this option if you want to use OMAP Dual-Mode timers.
|
|
|
|
choice
|
|
prompt "Low-level debug console UART"
|
|
depends on ARCH_OMAP
|
|
default OMAP_LL_DEBUG_UART1
|
|
|
|
config OMAP_LL_DEBUG_UART1
|
|
bool "UART1"
|
|
|
|
config OMAP_LL_DEBUG_UART2
|
|
bool "UART2"
|
|
|
|
config OMAP_LL_DEBUG_UART3
|
|
bool "UART3"
|
|
|
|
endchoice
|
|
|
|
config OMAP_SERIAL_WAKE
|
|
bool "Enable wake-up events for serial ports"
|
|
depends on OMAP_MUX
|
|
default y
|
|
help
|
|
Select this option if you want to have your system wake up
|
|
to data on the serial RX line. This allows you to wake the
|
|
system from serial console.
|
|
|
|
endmenu
|
|
|
|
endif
|