forked from Minki/linux
a97e384ba7
This makes it possible to select CONFIG_SND_MMP_SOC_SSPA directly, as opposed to via CONFIG_SND_MMP_SOC, and for the driver to bind to a device tree node. That makes the driver useful on Device Tree based systems, with audio-graph-card or simple-card. The aforementioned card drivers control the master clock themselves and don't call the set_dai_sysclk() or set_dai_pll(), thus the respective handlers don't serve any purpose anymore. Instead, they return early and the hw_params() handler sets the appropriate bitclk itself. The register range is split into two -- for the RX block and for the TX block. On a MMP2 there are two pairs of them; the first one has the clock controller in the middle, while the second just has a hole: 0xd42a0c00 - 0xd42a0c30 RX1 0xd42a0c30 - 0xd42a0c40 Clocks 0xd42a0c80 - 0xd42a0cb0 TX1 0xd42a0d00 - 0xd42a0d30 RX2 0xd42a0d80 - 0xd42a0cb0 TX2 For this reason, mmp_sspa_write_reg() and mmp_sspa_read_reg() are replaced with direct calls to I/O routines. Tested on a MMP2-based OLPC XO-1.75 laptop with rt5631 coded, mmp_tdma DMA engine and MMP2 clock controller glued together with audio-graph-card. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Link: https://lore.kernel.org/r/20200511210134.1224532-12-lkundrak@v3.sk Signed-off-by: Mark Brown <broonie@kernel.org>
71 lines
2.4 KiB
C
71 lines
2.4 KiB
C
/* SPDX-License-Identifier: GPL-2.0-or-later */
|
|
/*
|
|
* linux/sound/soc/pxa/mmp-sspa.h
|
|
*
|
|
* Copyright (C) 2011 Marvell International Ltd.
|
|
*/
|
|
#ifndef _MMP_SSPA_H
|
|
#define _MMP_SSPA_H
|
|
|
|
/*
|
|
* SSPA Registers
|
|
*/
|
|
#define SSPA_D (0x00)
|
|
#define SSPA_ID (0x04)
|
|
#define SSPA_CTL (0x08)
|
|
#define SSPA_SP (0x0c)
|
|
#define SSPA_FIFO_UL (0x10)
|
|
#define SSPA_INT_MASK (0x14)
|
|
#define SSPA_C (0x18)
|
|
#define SSPA_FIFO_NOFS (0x1c)
|
|
#define SSPA_FIFO_SIZE (0x20)
|
|
|
|
/* SSPA Control Register */
|
|
#define SSPA_CTL_XPH (1 << 31) /* Read Phase */
|
|
#define SSPA_CTL_XFIG (1 << 15) /* Transmit Zeros when FIFO Empty */
|
|
#define SSPA_CTL_JST (1 << 3) /* Audio Sample Justification */
|
|
#define SSPA_CTL_XFRLEN2_MASK (7 << 24)
|
|
#define SSPA_CTL_XFRLEN2(x) ((x) << 24) /* Transmit Frame Length in Phase 2 */
|
|
#define SSPA_CTL_XWDLEN2_MASK (7 << 21)
|
|
#define SSPA_CTL_XWDLEN2(x) ((x) << 21) /* Transmit Word Length in Phase 2 */
|
|
#define SSPA_CTL_XDATDLY(x) ((x) << 19) /* Transmit Data Delay */
|
|
#define SSPA_CTL_XSSZ2_MASK (7 << 16)
|
|
#define SSPA_CTL_XSSZ2(x) ((x) << 16) /* Transmit Sample Audio Size */
|
|
#define SSPA_CTL_XFRLEN1_MASK (7 << 8)
|
|
#define SSPA_CTL_XFRLEN1(x) ((x) << 8) /* Transmit Frame Length in Phase 1 */
|
|
#define SSPA_CTL_XWDLEN1_MASK (7 << 5)
|
|
#define SSPA_CTL_XWDLEN1(x) ((x) << 5) /* Transmit Word Length in Phase 1 */
|
|
#define SSPA_CTL_XSSZ1_MASK (7 << 0)
|
|
#define SSPA_CTL_XSSZ1(x) ((x) << 0) /* XSSZ1 */
|
|
|
|
#define SSPA_CTL_8_BITS (0x0) /* Sample Size */
|
|
#define SSPA_CTL_12_BITS (0x1)
|
|
#define SSPA_CTL_16_BITS (0x2)
|
|
#define SSPA_CTL_20_BITS (0x3)
|
|
#define SSPA_CTL_24_BITS (0x4)
|
|
#define SSPA_CTL_32_BITS (0x5)
|
|
|
|
/* SSPA Serial Port Register */
|
|
#define SSPA_SP_WEN (1 << 31) /* Write Configuration Enable */
|
|
#define SSPA_SP_MSL (1 << 18) /* Master Slave Configuration */
|
|
#define SSPA_SP_CLKP (1 << 17) /* CLKP Polarity Clock Edge Select */
|
|
#define SSPA_SP_FSP (1 << 16) /* FSP Polarity Clock Edge Select */
|
|
#define SSPA_SP_FFLUSH (1 << 2) /* FIFO Flush */
|
|
#define SSPA_SP_S_RST (1 << 1) /* Active High Reset Signal */
|
|
#define SSPA_SP_S_EN (1 << 0) /* Serial Clock Domain Enable */
|
|
#define SSPA_SP_FWID_MASK (0x3f << 20)
|
|
#define SSPA_SP_FWID(x) ((x) << 20) /* Frame-Sync Width */
|
|
#define SSPA_TXSP_FPER_MASK (0x3f << 4)
|
|
#define SSPA_TXSP_FPER(x) ((x) << 4) /* Frame-Sync Active */
|
|
|
|
/* sspa clock sources */
|
|
#define MMP_SSPA_CLK_PLL 0
|
|
#define MMP_SSPA_CLK_VCXO 1
|
|
#define MMP_SSPA_CLK_AUDIO 3
|
|
|
|
/* sspa pll id */
|
|
#define MMP_SYSCLK 0
|
|
#define MMP_SSPA_CLK 1
|
|
|
|
#endif /* _MMP_SSPA_H */
|