linux/drivers/iio/adc/ad7606.h
Beniamin Bia f2a22e1e17 iio: adc: ad7606: Add support for software mode for ad7616
Support for ad7616 running in software was added. In order
to activate the software mode, HW_RNGSEL pins must be pulled low.
Oversampling and input ranges are now configured in corresponding
registers. Ad7616 has multiple scale options when it is configured
in software mode.
Also, in order to support multiple devices in software mode, the spi
calculation of registers address must be generic. Because
the length of address and bit which specifies the read/write operation is
different for every device, calculation of address was made generic.

Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2019-07-28 08:56:08 +01:00

169 lines
5.6 KiB
C

/* SPDX-License-Identifier: GPL-2.0 */
/*
* AD7606 ADC driver
*
* Copyright 2011 Analog Devices Inc.
*/
#ifndef IIO_ADC_AD7606_H_
#define IIO_ADC_AD7606_H_
#define AD760X_CHANNEL(num, mask_sep, mask_type, mask_all) { \
.type = IIO_VOLTAGE, \
.indexed = 1, \
.channel = num, \
.address = num, \
.info_mask_separate = mask_sep, \
.info_mask_shared_by_type = mask_type, \
.info_mask_shared_by_all = mask_all, \
.scan_index = num, \
.scan_type = { \
.sign = 's', \
.realbits = 16, \
.storagebits = 16, \
.endianness = IIO_CPU, \
}, \
}
#define AD7605_CHANNEL(num) \
AD760X_CHANNEL(num, BIT(IIO_CHAN_INFO_RAW), \
BIT(IIO_CHAN_INFO_SCALE), 0)
#define AD7606_CHANNEL(num) \
AD760X_CHANNEL(num, BIT(IIO_CHAN_INFO_RAW), \
BIT(IIO_CHAN_INFO_SCALE), \
BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO))
#define AD7616_CHANNEL(num) \
AD760X_CHANNEL(num, BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),\
0, BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO))
/**
* struct ad7606_chip_info - chip specific information
* @channels: channel specification
* @num_channels: number of channels
* @oversampling_avail pointer to the array which stores the available
* oversampling ratios.
* @oversampling_num number of elements stored in oversampling_avail array
* @os_req_reset some devices require a reset to update oversampling
*/
struct ad7606_chip_info {
const struct iio_chan_spec *channels;
unsigned int num_channels;
const unsigned int *oversampling_avail;
unsigned int oversampling_num;
bool os_req_reset;
};
/**
* struct ad7606_state - driver instance specific data
* @dev pointer to kernel device
* @chip_info entry in the table of chips that describes this device
* @reg regulator info for the the power supply of the device
* @bops bus operations (SPI or parallel)
* @range voltage range selection, selects which scale to apply
* @oversampling oversampling selection
* @base_address address from where to read data in parallel operation
* @sw_mode_en software mode enabled
* @scale_avail pointer to the array which stores the available scales
* @num_scales number of elements stored in the scale_avail array
* @oversampling_avail pointer to the array which stores the available
* oversampling ratios.
* @num_os_ratios number of elements stored in oversampling_avail array
* @write_scale pointer to the function which writes the scale
* @write_os pointer to the function which writes the os
* @lock protect sensor state from concurrent accesses to GPIOs
* @gpio_convst GPIO descriptor for conversion start signal (CONVST)
* @gpio_reset GPIO descriptor for device hard-reset
* @gpio_range GPIO descriptor for range selection
* @gpio_standby GPIO descriptor for stand-by signal (STBY),
* controls power-down mode of device
* @gpio_frstdata GPIO descriptor for reading from device when data
* is being read on the first channel
* @gpio_os GPIO descriptors to control oversampling on the device
* @complete completion to indicate end of conversion
* @trig The IIO trigger associated with the device.
* @data buffer for reading data from the device
* @d16 be16 buffer for reading data from the device
*/
struct ad7606_state {
struct device *dev;
const struct ad7606_chip_info *chip_info;
struct regulator *reg;
const struct ad7606_bus_ops *bops;
unsigned int range[16];
unsigned int oversampling;
void __iomem *base_address;
bool sw_mode_en;
const unsigned int *scale_avail;
unsigned int num_scales;
const unsigned int *oversampling_avail;
unsigned int num_os_ratios;
int (*write_scale)(struct iio_dev *indio_dev, int ch, int val);
int (*write_os)(struct iio_dev *indio_dev, int val);
struct mutex lock; /* protect sensor state */
struct gpio_desc *gpio_convst;
struct gpio_desc *gpio_reset;
struct gpio_desc *gpio_range;
struct gpio_desc *gpio_standby;
struct gpio_desc *gpio_frstdata;
struct gpio_descs *gpio_os;
struct iio_trigger *trig;
struct completion completion;
/*
* DMA (thus cache coherency maintenance) requires the
* transfer buffers to live in their own cache lines.
* 16 * 16-bit samples + 64-bit timestamp
*/
unsigned short data[20] ____cacheline_aligned;
__be16 d16[2];
};
/**
* struct ad7606_bus_ops - driver bus operations
* @read_block function pointer for reading blocks of data
* @sw_mode_config: pointer to a function which configured the device
* for software mode
* @reg_read function pointer for reading spi register
* @reg_write function pointer for writing spi register
* @write_mask function pointer for write spi register with mask
* @rd_wr_cmd pointer to the function which calculates the spi address
*/
struct ad7606_bus_ops {
/* more methods added in future? */
int (*read_block)(struct device *dev, int num, void *data);
int (*sw_mode_config)(struct iio_dev *indio_dev);
int (*reg_read)(struct ad7606_state *st, unsigned int addr);
int (*reg_write)(struct ad7606_state *st,
unsigned int addr,
unsigned int val);
int (*write_mask)(struct ad7606_state *st,
unsigned int addr,
unsigned long mask,
unsigned int val);
u16 (*rd_wr_cmd)(int addr, char isWriteOp);
};
int ad7606_probe(struct device *dev, int irq, void __iomem *base_address,
const char *name, unsigned int id,
const struct ad7606_bus_ops *bops);
enum ad7606_supported_device_ids {
ID_AD7605_4,
ID_AD7606_8,
ID_AD7606_6,
ID_AD7606_4,
ID_AD7616,
};
#ifdef CONFIG_PM_SLEEP
extern const struct dev_pm_ops ad7606_pm_ops;
#define AD7606_PM_OPS (&ad7606_pm_ops)
#else
#define AD7606_PM_OPS NULL
#endif
#endif /* IIO_ADC_AD7606_H_ */