linux/drivers/net/dsa/mv88e6131.c
Guenter Roeck d198893e73 net: dsa: mv88e6131: Determine and use number of switch ports
Determine and use number of switch ports from chip ID instead of always
using the maximum, and return error when an attempt is made to access a
non-existing port.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-01 22:55:40 -04:00

407 lines
10 KiB
C

/*
* net/dsa/mv88e6131.c - Marvell 88e6095/6095f/6131 switch chip support
* Copyright (c) 2008-2009 Marvell Semiconductor
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/delay.h>
#include <linux/jiffies.h>
#include <linux/list.h>
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/phy.h>
#include <net/dsa.h>
#include "mv88e6xxx.h"
static char *mv88e6131_probe(struct device *host_dev, int sw_addr)
{
struct mii_bus *bus = dsa_host_dev_to_mii_bus(host_dev);
int ret;
if (bus == NULL)
return NULL;
ret = __mv88e6xxx_reg_read(bus, sw_addr, REG_PORT(0), 0x03);
if (ret >= 0) {
int ret_masked = ret & 0xfff0;
if (ret_masked == ID_6085)
return "Marvell 88E6085";
if (ret_masked == ID_6095)
return "Marvell 88E6095/88E6095F";
if (ret == ID_6131_B2)
return "Marvell 88E6131 (B2)";
if (ret_masked == ID_6131)
return "Marvell 88E6131";
}
return NULL;
}
static int mv88e6131_switch_reset(struct dsa_switch *ds)
{
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
int i;
int ret;
unsigned long timeout;
/* Set all ports to the disabled state. */
for (i = 0; i < ps->num_ports; i++) {
ret = REG_READ(REG_PORT(i), 0x04);
REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
}
/* Wait for transmit queues to drain. */
usleep_range(2000, 4000);
/* Reset the switch. */
REG_WRITE(REG_GLOBAL, 0x04, 0xc400);
/* Wait up to one second for reset to complete. */
timeout = jiffies + 1 * HZ;
while (time_before(jiffies, timeout)) {
ret = REG_READ(REG_GLOBAL, 0x00);
if ((ret & 0xc800) == 0xc800)
break;
usleep_range(1000, 2000);
}
if (time_after(jiffies, timeout))
return -ETIMEDOUT;
return 0;
}
static int mv88e6131_setup_global(struct dsa_switch *ds)
{
int ret;
int i;
/* Enable the PHY polling unit, don't discard packets with
* excessive collisions, use a weighted fair queueing scheme
* to arbitrate between packet queues, set the maximum frame
* size to 1632, and mask all interrupt sources.
*/
REG_WRITE(REG_GLOBAL, 0x04, 0x4400);
/* Set the default address aging time to 5 minutes, and
* enable address learn messages to be sent to all message
* ports.
*/
REG_WRITE(REG_GLOBAL, 0x0a, 0x0148);
/* Configure the priority mapping registers. */
ret = mv88e6xxx_config_prio(ds);
if (ret < 0)
return ret;
/* Set the VLAN ethertype to 0x8100. */
REG_WRITE(REG_GLOBAL, 0x19, 0x8100);
/* Disable ARP mirroring, and configure the upstream port as
* the port to which ingress and egress monitor frames are to
* be sent.
*/
REG_WRITE(REG_GLOBAL, 0x1a, (dsa_upstream_port(ds) * 0x1100) | 0x00f0);
/* Disable cascade port functionality unless this device
* is used in a cascade configuration, and set the switch's
* DSA device number.
*/
if (ds->dst->pd->nr_chips > 1)
REG_WRITE(REG_GLOBAL, 0x1c, 0xf000 | (ds->index & 0x1f));
else
REG_WRITE(REG_GLOBAL, 0x1c, 0xe000 | (ds->index & 0x1f));
/* Send all frames with destination addresses matching
* 01:80:c2:00:00:0x to the CPU port.
*/
REG_WRITE(REG_GLOBAL2, 0x03, 0xffff);
/* Ignore removed tag data on doubly tagged packets, disable
* flow control messages, force flow control priority to the
* highest, and send all special multicast frames to the CPU
* port at the highest priority.
*/
REG_WRITE(REG_GLOBAL2, 0x05, 0x00ff);
/* Program the DSA routing table. */
for (i = 0; i < 32; i++) {
int nexthop;
nexthop = 0x1f;
if (ds->pd->rtable &&
i != ds->index && i < ds->dst->pd->nr_chips)
nexthop = ds->pd->rtable[i] & 0x1f;
REG_WRITE(REG_GLOBAL2, 0x06, 0x8000 | (i << 8) | nexthop);
}
/* Clear all trunk masks. */
for (i = 0; i < 8; i++)
REG_WRITE(REG_GLOBAL2, 0x07, 0x8000 | (i << 12) | 0x7ff);
/* Clear all trunk mappings. */
for (i = 0; i < 16; i++)
REG_WRITE(REG_GLOBAL2, 0x08, 0x8000 | (i << 11));
/* Force the priority of IGMP/MLD snoop frames and ARP frames
* to the highest setting.
*/
REG_WRITE(REG_GLOBAL2, 0x0f, 0x00ff);
return 0;
}
static int mv88e6131_setup_port(struct dsa_switch *ds, int p)
{
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
int addr = REG_PORT(p);
u16 val;
/* MAC Forcing register: don't force link, speed, duplex
* or flow control state to any particular values on physical
* ports, but force the CPU port and all DSA ports to 1000 Mb/s
* (100 Mb/s on 6085) full duplex.
*/
if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
if (ps->id == ID_6085)
REG_WRITE(addr, 0x01, 0x003d); /* 100 Mb/s */
else
REG_WRITE(addr, 0x01, 0x003e); /* 1000 Mb/s */
else
REG_WRITE(addr, 0x01, 0x0003);
/* Port Control: disable Core Tag, disable Drop-on-Lock,
* transmit frames unmodified, disable Header mode,
* enable IGMP/MLD snoop, disable DoubleTag, disable VLAN
* tunneling, determine priority by looking at 802.1p and
* IP priority fields (IP prio has precedence), and set STP
* state to Forwarding.
*
* If this is the upstream port for this switch, enable
* forwarding of unknown unicasts, and enable DSA tagging
* mode.
*
* If this is the link to another switch, use DSA tagging
* mode, but do not enable forwarding of unknown unicasts.
*/
val = 0x0433;
if (p == dsa_upstream_port(ds)) {
val |= 0x0104;
/* On 6085, unknown multicast forward is controlled
* here rather than in Port Control 2 register.
*/
if (ps->id == ID_6085)
val |= 0x0008;
}
if (ds->dsa_port_mask & (1 << p))
val |= 0x0100;
REG_WRITE(addr, 0x04, val);
/* Port Control 2: don't force a good FCS, don't use
* VLAN-based, source address-based or destination
* address-based priority overrides, don't let the switch
* add or strip 802.1q tags, don't discard tagged or
* untagged frames on this port, do a destination address
* lookup on received packets as usual, don't send a copy
* of all transmitted/received frames on this port to the
* CPU, and configure the upstream port number.
*
* If this is the upstream port for this switch, enable
* forwarding of unknown multicast addresses.
*/
if (ps->id == ID_6085)
/* on 6085, bits 3:0 are reserved, bit 6 control ARP
* mirroring, and multicast forward is handled in
* Port Control register.
*/
REG_WRITE(addr, 0x08, 0x0080);
else {
val = 0x0080 | dsa_upstream_port(ds);
if (p == dsa_upstream_port(ds))
val |= 0x0040;
REG_WRITE(addr, 0x08, val);
}
/* Rate Control: disable ingress rate limiting. */
REG_WRITE(addr, 0x09, 0x0000);
/* Rate Control 2: disable egress rate limiting. */
REG_WRITE(addr, 0x0a, 0x0000);
/* Port Association Vector: when learning source addresses
* of packets, add the address to the address database using
* a port bitmap that has only the bit for this port set and
* the other bits clear.
*/
REG_WRITE(addr, 0x0b, 1 << p);
/* Tag Remap: use an identity 802.1p prio -> switch prio
* mapping.
*/
REG_WRITE(addr, 0x18, 0x3210);
/* Tag Remap 2: use an identity 802.1p prio -> switch prio
* mapping.
*/
REG_WRITE(addr, 0x19, 0x7654);
return mv88e6xxx_setup_port_common(ds, p);
}
static int mv88e6131_setup(struct dsa_switch *ds)
{
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
int i;
int ret;
ret = mv88e6xxx_setup_common(ds);
if (ret < 0)
return ret;
mv88e6xxx_ppu_state_init(ds);
switch (ps->id) {
case ID_6085:
ps->num_ports = 10;
break;
case ID_6095:
ps->num_ports = 11;
break;
case ID_6131:
case ID_6131_B2:
ps->num_ports = 8;
break;
default:
return -ENODEV;
}
ret = mv88e6131_switch_reset(ds);
if (ret < 0)
return ret;
/* @@@ initialise vtu and atu */
ret = mv88e6131_setup_global(ds);
if (ret < 0)
return ret;
for (i = 0; i < ps->num_ports; i++) {
ret = mv88e6131_setup_port(ds, i);
if (ret < 0)
return ret;
}
return 0;
}
static int mv88e6131_port_to_phy_addr(struct dsa_switch *ds, int port)
{
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
if (port >= 0 && port < ps->num_ports)
return port;
return -EINVAL;
}
static int
mv88e6131_phy_read(struct dsa_switch *ds, int port, int regnum)
{
int addr = mv88e6131_port_to_phy_addr(ds, port);
if (addr < 0)
return addr;
return mv88e6xxx_phy_read_ppu(ds, addr, regnum);
}
static int
mv88e6131_phy_write(struct dsa_switch *ds,
int port, int regnum, u16 val)
{
int addr = mv88e6131_port_to_phy_addr(ds, port);
if (addr < 0)
return addr;
return mv88e6xxx_phy_write_ppu(ds, addr, regnum, val);
}
static struct mv88e6xxx_hw_stat mv88e6131_hw_stats[] = {
{ "in_good_octets", 8, 0x00, },
{ "in_bad_octets", 4, 0x02, },
{ "in_unicast", 4, 0x04, },
{ "in_broadcasts", 4, 0x06, },
{ "in_multicasts", 4, 0x07, },
{ "in_pause", 4, 0x16, },
{ "in_undersize", 4, 0x18, },
{ "in_fragments", 4, 0x19, },
{ "in_oversize", 4, 0x1a, },
{ "in_jabber", 4, 0x1b, },
{ "in_rx_error", 4, 0x1c, },
{ "in_fcs_error", 4, 0x1d, },
{ "out_octets", 8, 0x0e, },
{ "out_unicast", 4, 0x10, },
{ "out_broadcasts", 4, 0x13, },
{ "out_multicasts", 4, 0x12, },
{ "out_pause", 4, 0x15, },
{ "excessive", 4, 0x11, },
{ "collisions", 4, 0x1e, },
{ "deferred", 4, 0x05, },
{ "single", 4, 0x14, },
{ "multiple", 4, 0x17, },
{ "out_fcs_error", 4, 0x03, },
{ "late", 4, 0x1f, },
{ "hist_64bytes", 4, 0x08, },
{ "hist_65_127bytes", 4, 0x09, },
{ "hist_128_255bytes", 4, 0x0a, },
{ "hist_256_511bytes", 4, 0x0b, },
{ "hist_512_1023bytes", 4, 0x0c, },
{ "hist_1024_max_bytes", 4, 0x0d, },
};
static void
mv88e6131_get_strings(struct dsa_switch *ds, int port, uint8_t *data)
{
mv88e6xxx_get_strings(ds, ARRAY_SIZE(mv88e6131_hw_stats),
mv88e6131_hw_stats, port, data);
}
static void
mv88e6131_get_ethtool_stats(struct dsa_switch *ds,
int port, uint64_t *data)
{
mv88e6xxx_get_ethtool_stats(ds, ARRAY_SIZE(mv88e6131_hw_stats),
mv88e6131_hw_stats, port, data);
}
static int mv88e6131_get_sset_count(struct dsa_switch *ds)
{
return ARRAY_SIZE(mv88e6131_hw_stats);
}
struct dsa_switch_driver mv88e6131_switch_driver = {
.tag_protocol = DSA_TAG_PROTO_DSA,
.priv_size = sizeof(struct mv88e6xxx_priv_state),
.probe = mv88e6131_probe,
.setup = mv88e6131_setup,
.set_addr = mv88e6xxx_set_addr_direct,
.phy_read = mv88e6131_phy_read,
.phy_write = mv88e6131_phy_write,
.poll_link = mv88e6xxx_poll_link,
.get_strings = mv88e6131_get_strings,
.get_ethtool_stats = mv88e6131_get_ethtool_stats,
.get_sset_count = mv88e6131_get_sset_count,
};
MODULE_ALIAS("platform:mv88e6085");
MODULE_ALIAS("platform:mv88e6095");
MODULE_ALIAS("platform:mv88e6095f");
MODULE_ALIAS("platform:mv88e6131");