599c376c49
Commit 7800064ba5 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the GPIO interrupts earlier until I found some suitable pins
to test with. We can mux the MMC card detect and write protect pins
from SD_SDCD and SD_SDWP mode to use a normal GPIO interrupts that
are also suitable for the MMC subsystem.
This turned out several issues that need to be fixed:
- I set the GPIO type wrong to be compatible with omap3 instead
of omap4. The GPIO controller on dm816x has EOI interrupt
register like omap4 and am335x.
- I got the GPIO interrupt numbers wrong as each bank has two
and we only use one. They need to be set up the same way as
on am335x.
- The gpio banks are missing interrupt controller related
properties.
With these changes the GPIO interrupts can be used with the
MMC card detect pin, so let's wire that up. Let's also mux all
the MMC lines for completeness while at it.
For the first GPIO bank I tested using GPMC lines temporarily
muxed to GPIOs on the dip switch 10.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
429 lines
9.3 KiB
Plaintext
429 lines
9.3 KiB
Plaintext
/*
|
|
* This file is licensed under the terms of the GNU General Public License
|
|
* version 2. This program is licensed "as is" without any warranty of any
|
|
* kind, whether express or implied.
|
|
*/
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/pinctrl/omap.h>
|
|
|
|
#include "skeleton.dtsi"
|
|
|
|
/ {
|
|
compatible = "ti,dm816";
|
|
interrupt-parent = <&intc>;
|
|
|
|
aliases {
|
|
i2c0 = &i2c1;
|
|
i2c1 = &i2c2;
|
|
serial0 = &uart1;
|
|
serial1 = &uart2;
|
|
serial2 = &uart3;
|
|
ethernet0 = ð0;
|
|
ethernet1 = ð1;
|
|
};
|
|
|
|
cpus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
cpu@0 {
|
|
compatible = "arm,cortex-a8";
|
|
device_type = "cpu";
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
pmu {
|
|
compatible = "arm,cortex-a8-pmu";
|
|
interrupts = <3>;
|
|
};
|
|
|
|
/*
|
|
* The soc node represents the soc top level view. It is used for IPs
|
|
* that are not memory mapped in the MPU view or for the MPU itself.
|
|
*/
|
|
soc {
|
|
compatible = "ti,omap-infra";
|
|
mpu {
|
|
compatible = "ti,omap3-mpu";
|
|
ti,hwmods = "mpu";
|
|
};
|
|
};
|
|
|
|
/*
|
|
* XXX: Use a flat representation of the dm816x interconnect.
|
|
* The real dm816x interconnect network is quite complex. Since
|
|
* it will not bring real advantage to represent that in DT
|
|
* for the moment, just use a fake OCP bus entry to represent
|
|
* the whole bus hierarchy.
|
|
*/
|
|
ocp {
|
|
compatible = "ti,omap3-l3-smx", "simple-bus";
|
|
reg = <0x44000000 0x10000>;
|
|
interrupts = <9 10>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
ti,hwmods = "l3_main";
|
|
|
|
prcm: prcm@48180000 {
|
|
compatible = "ti,dm816-prcm";
|
|
reg = <0x48180000 0x4000>;
|
|
|
|
prcm_clocks: clocks {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
|
|
prcm_clockdomains: clockdomains {
|
|
};
|
|
};
|
|
|
|
scrm: scrm@48140000 {
|
|
compatible = "ti,dm816-scrm", "simple-bus";
|
|
reg = <0x48140000 0x21000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges = <0 0x48140000 0x21000>;
|
|
|
|
dm816x_pinmux: pinmux@800 {
|
|
compatible = "pinctrl-single";
|
|
reg = <0x800 0x50a>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
pinctrl-single,register-width = <16>;
|
|
pinctrl-single,function-mask = <0xf>;
|
|
};
|
|
|
|
/* Device Configuration Registers */
|
|
scm_conf: syscon@600 {
|
|
compatible = "syscon", "simple-bus";
|
|
reg = <0x600 0x110>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges = <0 0x600 0x110>;
|
|
|
|
usb_phy0: usb-phy@20 {
|
|
compatible = "ti,dm8168-usb-phy";
|
|
reg = <0x20 0x8>;
|
|
reg-names = "phy";
|
|
clocks = <&main_fapll 6>;
|
|
clock-names = "refclk";
|
|
#phy-cells = <0>;
|
|
syscon = <&scm_conf>;
|
|
};
|
|
|
|
usb_phy1: usb-phy@28 {
|
|
compatible = "ti,dm8168-usb-phy";
|
|
reg = <0x28 0x8>;
|
|
reg-names = "phy";
|
|
clocks = <&main_fapll 6>;
|
|
clock-names = "refclk";
|
|
#phy-cells = <0>;
|
|
syscon = <&scm_conf>;
|
|
};
|
|
};
|
|
|
|
scrm_clocks: clocks {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
|
|
scrm_clockdomains: clockdomains {
|
|
};
|
|
};
|
|
|
|
edma: edma@49000000 {
|
|
compatible = "ti,edma3";
|
|
ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2", "tptc3";
|
|
reg = <0x49000000 0x10000>,
|
|
<0x44e10f90 0x40>;
|
|
interrupts = <12 13 14>;
|
|
#dma-cells = <1>;
|
|
};
|
|
|
|
elm: elm@48080000 {
|
|
compatible = "ti,816-elm";
|
|
ti,hwmods = "elm";
|
|
reg = <0x48080000 0x2000>;
|
|
interrupts = <4>;
|
|
};
|
|
|
|
gpio1: gpio@48032000 {
|
|
compatible = "ti,omap4-gpio";
|
|
ti,hwmods = "gpio1";
|
|
ti,gpio-always-on;
|
|
reg = <0x48032000 0x1000>;
|
|
interrupts = <96>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
gpio2: gpio@4804c000 {
|
|
compatible = "ti,omap4-gpio";
|
|
ti,hwmods = "gpio2";
|
|
ti,gpio-always-on;
|
|
reg = <0x4804c000 0x1000>;
|
|
interrupts = <98>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
gpmc: gpmc@50000000 {
|
|
compatible = "ti,am3352-gpmc";
|
|
ti,hwmods = "gpmc";
|
|
reg = <0x50000000 0x2000>;
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
interrupts = <100>;
|
|
gpmc,num-cs = <6>;
|
|
gpmc,num-waitpins = <2>;
|
|
};
|
|
|
|
i2c1: i2c@48028000 {
|
|
compatible = "ti,omap4-i2c";
|
|
ti,hwmods = "i2c1";
|
|
reg = <0x48028000 0x1000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
interrupts = <70>;
|
|
dmas = <&edma 58 &edma 59>;
|
|
dma-names = "tx", "rx";
|
|
};
|
|
|
|
i2c2: i2c@4802a000 {
|
|
compatible = "ti,omap4-i2c";
|
|
ti,hwmods = "i2c2";
|
|
reg = <0x4802a000 0x1000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
interrupts = <71>;
|
|
dmas = <&edma 60 &edma 61>;
|
|
dma-names = "tx", "rx";
|
|
};
|
|
|
|
intc: interrupt-controller@48200000 {
|
|
compatible = "ti,dm816-intc";
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
reg = <0x48200000 0x1000>;
|
|
};
|
|
|
|
mailbox: mailbox@480c8000 {
|
|
compatible = "ti,omap4-mailbox";
|
|
reg = <0x480c8000 0x2000>;
|
|
interrupts = <77>;
|
|
ti,hwmods = "mailbox";
|
|
ti,mbox-num-users = <4>;
|
|
ti,mbox-num-fifos = <12>;
|
|
mbox_dsp: mbox_dsp {
|
|
ti,mbox-tx = <3 0 0>;
|
|
ti,mbox-rx = <0 0 0>;
|
|
};
|
|
};
|
|
|
|
mdio: mdio@4a100800 {
|
|
compatible = "ti,davinci_mdio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <0x4a100800 0x100>;
|
|
ti,hwmods = "davinci_mdio";
|
|
bus_freq = <1000000>;
|
|
phy0: ethernet-phy@0 {
|
|
reg = <1>;
|
|
};
|
|
phy1: ethernet-phy@1 {
|
|
reg = <2>;
|
|
};
|
|
};
|
|
|
|
eth0: ethernet@4a100000 {
|
|
compatible = "ti,dm816-emac";
|
|
ti,hwmods = "emac0";
|
|
reg = <0x4a100000 0x800
|
|
0x4a100900 0x3700>;
|
|
clocks = <&sysclk24_ck>;
|
|
syscon = <&scm_conf>;
|
|
ti,davinci-ctrl-reg-offset = <0>;
|
|
ti,davinci-ctrl-mod-reg-offset = <0x900>;
|
|
ti,davinci-ctrl-ram-offset = <0x2000>;
|
|
ti,davinci-ctrl-ram-size = <0x2000>;
|
|
interrupts = <40 41 42 43>;
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
eth1: ethernet@4a120000 {
|
|
compatible = "ti,dm816-emac";
|
|
ti,hwmods = "emac1";
|
|
reg = <0x4a120000 0x4000>;
|
|
clocks = <&sysclk24_ck>;
|
|
syscon = <&scm_conf>;
|
|
ti,davinci-ctrl-reg-offset = <0>;
|
|
ti,davinci-ctrl-mod-reg-offset = <0x900>;
|
|
ti,davinci-ctrl-ram-offset = <0x2000>;
|
|
ti,davinci-ctrl-ram-size = <0x2000>;
|
|
interrupts = <44 45 46 47>;
|
|
phy-handle = <&phy1>;
|
|
};
|
|
|
|
mcspi1: spi@48030000 {
|
|
compatible = "ti,omap4-mcspi";
|
|
reg = <0x48030000 0x1000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
interrupts = <65>;
|
|
ti,spi-num-cs = <4>;
|
|
ti,hwmods = "mcspi1";
|
|
dmas = <&edma 16 &edma 17
|
|
&edma 18 &edma 19>;
|
|
dma-names = "tx0", "rx0", "tx1", "rx1";
|
|
};
|
|
|
|
mmc1: mmc@48060000 {
|
|
compatible = "ti,omap4-hsmmc";
|
|
reg = <0x48060000 0x11000>;
|
|
ti,hwmods = "mmc1";
|
|
interrupts = <64>;
|
|
dmas = <&edma 24 &edma 25>;
|
|
dma-names = "tx", "rx";
|
|
};
|
|
|
|
timer1: timer@4802e000 {
|
|
compatible = "ti,dm816-timer";
|
|
reg = <0x4802e000 0x2000>;
|
|
interrupts = <67>;
|
|
ti,hwmods = "timer1";
|
|
ti,timer-alwon;
|
|
};
|
|
|
|
timer2: timer@48040000 {
|
|
compatible = "ti,dm816-timer";
|
|
reg = <0x48040000 0x2000>;
|
|
interrupts = <68>;
|
|
ti,hwmods = "timer2";
|
|
};
|
|
|
|
timer3: timer@48042000 {
|
|
compatible = "ti,dm816-timer";
|
|
reg = <0x48042000 0x2000>;
|
|
interrupts = <69>;
|
|
ti,hwmods = "timer3";
|
|
};
|
|
|
|
timer4: timer@48044000 {
|
|
compatible = "ti,dm816-timer";
|
|
reg = <0x48044000 0x2000>;
|
|
interrupts = <92>;
|
|
ti,hwmods = "timer4";
|
|
};
|
|
|
|
timer5: timer@48046000 {
|
|
compatible = "ti,dm816-timer";
|
|
reg = <0x48046000 0x2000>;
|
|
interrupts = <93>;
|
|
ti,hwmods = "timer5";
|
|
};
|
|
|
|
timer6: timer@48048000 {
|
|
compatible = "ti,dm816-timer";
|
|
reg = <0x48048000 0x2000>;
|
|
interrupts = <94>;
|
|
ti,hwmods = "timer6";
|
|
};
|
|
|
|
timer7: timer@4804a000 {
|
|
compatible = "ti,dm816-timer";
|
|
reg = <0x4804a000 0x2000>;
|
|
interrupts = <95>;
|
|
ti,hwmods = "timer7";
|
|
};
|
|
|
|
uart1: uart@48020000 {
|
|
compatible = "ti,omap3-uart";
|
|
ti,hwmods = "uart1";
|
|
reg = <0x48020000 0x2000>;
|
|
clock-frequency = <48000000>;
|
|
interrupts = <72>;
|
|
dmas = <&edma 26 &edma 27>;
|
|
dma-names = "tx", "rx";
|
|
};
|
|
|
|
uart2: uart@48022000 {
|
|
compatible = "ti,omap3-uart";
|
|
ti,hwmods = "uart2";
|
|
reg = <0x48022000 0x2000>;
|
|
clock-frequency = <48000000>;
|
|
interrupts = <73>;
|
|
dmas = <&edma 28 &edma 29>;
|
|
dma-names = "tx", "rx";
|
|
};
|
|
|
|
uart3: uart@48024000 {
|
|
compatible = "ti,omap3-uart";
|
|
ti,hwmods = "uart3";
|
|
reg = <0x48024000 0x2000>;
|
|
clock-frequency = <48000000>;
|
|
interrupts = <74>;
|
|
dmas = <&edma 30 &edma 31>;
|
|
dma-names = "tx", "rx";
|
|
};
|
|
|
|
/* NOTE: USB needs a transceiver driver for phys to work */
|
|
usb: usb_otg_hs@47401000 {
|
|
compatible = "ti,am33xx-usb";
|
|
reg = <0x47401000 0x400000>;
|
|
ranges;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ti,hwmods = "usb_otg_hs";
|
|
|
|
usb0: usb@47401000 {
|
|
compatible = "ti,musb-am33xx";
|
|
reg = <0x47401400 0x400
|
|
0x47401000 0x200>;
|
|
reg-names = "mc", "control";
|
|
interrupts = <18>;
|
|
interrupt-names = "mc";
|
|
dr_mode = "host";
|
|
interface-type = <0>;
|
|
phys = <&usb_phy0>;
|
|
phy-names = "usb2-phy";
|
|
mentor,multipoint = <1>;
|
|
mentor,num-eps = <16>;
|
|
mentor,ram-bits = <12>;
|
|
mentor,power = <500>;
|
|
};
|
|
|
|
usb1: usb@47401800 {
|
|
compatible = "ti,musb-am33xx";
|
|
reg = <0x47401c00 0x400
|
|
0x47401800 0x200>;
|
|
reg-names = "mc", "control";
|
|
interrupts = <19>;
|
|
interrupt-names = "mc";
|
|
dr_mode = "host";
|
|
interface-type = <0>;
|
|
phys = <&usb_phy1>;
|
|
phy-names = "usb2-phy";
|
|
mentor,multipoint = <1>;
|
|
mentor,num-eps = <16>;
|
|
mentor,ram-bits = <12>;
|
|
mentor,power = <500>;
|
|
};
|
|
};
|
|
|
|
wd_timer2: wd_timer@480c2000 {
|
|
compatible = "ti,omap3-wdt";
|
|
ti,hwmods = "wd_timer";
|
|
reg = <0x480c2000 0x1000>;
|
|
interrupts = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
#include "dm816x-clocks.dtsi"
|