forked from Minki/linux
aa29efb445
NXP LPC32xx SoC has one USB OTG controller, which is supposed to work with an external phy (default is NXP ISP1301). Practically the USB controller contains 5 subdevices: - host controller 0x3102 0000 -- 0x3102 00FF - OTG controller 0x3102 0100 -- 0x3102 01FF - device controller 0x3102 0200 -- 0x3102 02FF - I2C controller 0x3102 0300 -- 0x3102 03FF - clock controller 0x3102 0F00 -- 0x3102 0FFF The USB controller can be considered as a "bus", because the subdevices above are relatively independent, for example I2C controller is the same as other two general purpose I2C controllers found on SoC. The change is not intended to modify any logic, but it rearranges existing device nodes, in future it is planned to add a USB clock controller device node into the same group. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
196 lines
3.6 KiB
Plaintext
196 lines
3.6 KiB
Plaintext
/*
|
|
* PHYTEC phyCORE-LPC3250 board
|
|
*
|
|
* Copyright 2012 Roland Stigge <stigge@antcom.de>
|
|
*
|
|
* The code contained herein is licensed under the GNU General Public
|
|
* License. You may obtain a copy of the GNU General Public License
|
|
* Version 2 or later at the following locations:
|
|
*
|
|
* http://www.opensource.org/licenses/gpl-license.html
|
|
* http://www.gnu.org/copyleft/gpl.html
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "lpc32xx.dtsi"
|
|
|
|
/ {
|
|
model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250";
|
|
compatible = "phytec,phy3250", "nxp,lpc3250";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0x80000000 0x4000000>;
|
|
};
|
|
|
|
ahb {
|
|
mac: ethernet@31060000 {
|
|
phy-mode = "rmii";
|
|
use-iram;
|
|
};
|
|
|
|
clcd@31040000 {
|
|
status = "okay";
|
|
};
|
|
|
|
/* 64MB Flash via SLC NAND controller */
|
|
slc: flash@20020000 {
|
|
status = "okay";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
nxp,wdr-clks = <14>;
|
|
nxp,wwidth = <40000000>;
|
|
nxp,whold = <100000000>;
|
|
nxp,wsetup = <100000000>;
|
|
nxp,rdr-clks = <14>;
|
|
nxp,rwidth = <40000000>;
|
|
nxp,rhold = <66666666>;
|
|
nxp,rsetup = <100000000>;
|
|
nand-on-flash-bbt;
|
|
gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
|
|
|
|
mtd0@00000000 {
|
|
label = "phy3250-boot";
|
|
reg = <0x00000000 0x00064000>;
|
|
read-only;
|
|
};
|
|
|
|
mtd1@00064000 {
|
|
label = "phy3250-uboot";
|
|
reg = <0x00064000 0x00190000>;
|
|
read-only;
|
|
};
|
|
|
|
mtd2@001f4000 {
|
|
label = "phy3250-ubt-prms";
|
|
reg = <0x001f4000 0x00010000>;
|
|
};
|
|
|
|
mtd3@00204000 {
|
|
label = "phy3250-kernel";
|
|
reg = <0x00204000 0x00400000>;
|
|
};
|
|
|
|
mtd4@00604000 {
|
|
label = "phy3250-rootfs";
|
|
reg = <0x00604000 0x039fc000>;
|
|
};
|
|
};
|
|
|
|
apb {
|
|
uart5: serial@40090000 {
|
|
status = "okay";
|
|
};
|
|
|
|
uart3: serial@40080000 {
|
|
status = "okay";
|
|
};
|
|
|
|
i2c1: i2c@400A0000 {
|
|
clock-frequency = <100000>;
|
|
|
|
pcf8563: rtc@51 {
|
|
compatible = "nxp,pcf8563";
|
|
reg = <0x51>;
|
|
};
|
|
|
|
uda1380: uda1380@18 {
|
|
compatible = "nxp,uda1380";
|
|
reg = <0x18>;
|
|
power-gpio = <&gpio 0x59 0>;
|
|
reset-gpio = <&gpio 0x51 0>;
|
|
dac-clk = "wspll";
|
|
};
|
|
};
|
|
|
|
i2c2: i2c@400A8000 {
|
|
clock-frequency = <100000>;
|
|
};
|
|
|
|
ssp0: ssp@20084000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
num-cs = <1>;
|
|
cs-gpios = <&gpio 3 5 0>;
|
|
|
|
eeprom: at25@0 {
|
|
pl022,interface = <0>;
|
|
pl022,com-mode = <0>;
|
|
pl022,rx-level-trig = <1>;
|
|
pl022,tx-level-trig = <1>;
|
|
pl022,ctrl-len = <11>;
|
|
pl022,wait-state = <0>;
|
|
pl022,duplex = <0>;
|
|
|
|
at25,byte-len = <0x8000>;
|
|
at25,addr-mode = <2>;
|
|
at25,page-size = <64>;
|
|
|
|
compatible = "atmel,at25";
|
|
reg = <0>;
|
|
spi-max-frequency = <5000000>;
|
|
};
|
|
};
|
|
|
|
sd@20098000 {
|
|
wp-gpios = <&gpio 3 0 0>;
|
|
cd-gpios = <&gpio 3 1 0>;
|
|
cd-inverted;
|
|
bus-width = <4>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
fab {
|
|
uart2: serial@40018000 {
|
|
status = "okay";
|
|
};
|
|
|
|
tsc@40048000 {
|
|
status = "okay";
|
|
};
|
|
|
|
key@40050000 {
|
|
status = "okay";
|
|
keypad,num-rows = <1>;
|
|
keypad,num-columns = <1>;
|
|
nxp,debounce-delay-ms = <3>;
|
|
nxp,scan-delay-ms = <34>;
|
|
linux,keymap = <0x00000002>;
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led0 { /* red */
|
|
gpios = <&gpio 5 1 0>; /* GPO_P3 1, GPIO 80, active high */
|
|
default-state = "off";
|
|
};
|
|
|
|
led1 { /* green */
|
|
gpios = <&gpio 5 14 0>; /* GPO_P3 14, GPIO 93, active high */
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
};
|
|
};
|
|
|
|
/* Here, choose exactly one from: ohci, usbd */
|
|
&ohci /* &usbd */ {
|
|
transceiver = <&isp1301>;
|
|
status = "okay";
|
|
};
|
|
|
|
&i2cusb {
|
|
clock-frequency = <100000>;
|
|
|
|
isp1301: usb-transceiver@2c {
|
|
compatible = "nxp,isp1301";
|
|
reg = <0x2c>;
|
|
};
|
|
};
|