forked from Minki/linux
331ae5fc3e
Add device tree binding for the BCM6345 interrupt controller. This controller is similar to the SMP-capable BCM7038 and the BCM3380 but with packed interrupt registers. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Acked-by: Rob Herring <robh@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org> Cc: devicetree@vger.kernel.org Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11804/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
58 lines
2.0 KiB
Plaintext
58 lines
2.0 KiB
Plaintext
Broadcom BCM6345-style Level 1 interrupt controller
|
|
|
|
This block is a first level interrupt controller that is typically connected
|
|
directly to one of the HW INT lines on each CPU.
|
|
|
|
Key elements of the hardware design include:
|
|
|
|
- 32, 64 or 128 incoming level IRQ lines
|
|
|
|
- Most onchip peripherals are wired directly to an L1 input
|
|
|
|
- A separate instance of the register set for each CPU, allowing individual
|
|
peripheral IRQs to be routed to any CPU
|
|
|
|
- Contains one or more enable/status word pairs per CPU
|
|
|
|
- No atomic set/clear operations
|
|
|
|
- No polarity/level/edge settings
|
|
|
|
- No FIFO or priority encoder logic; software is expected to read all
|
|
2-4 status words to determine which IRQs are pending
|
|
|
|
Required properties:
|
|
|
|
- compatible: should be "brcm,bcm<soc>-l1-intc", "brcm,bcm6345-l1-intc"
|
|
- reg: specifies the base physical address and size of the registers;
|
|
the number of supported IRQs is inferred from the size argument
|
|
- interrupt-controller: identifies the node as an interrupt controller
|
|
- #interrupt-cells: specifies the number of cells needed to encode an interrupt
|
|
source, should be 1.
|
|
- interrupt-parent: specifies the phandle to the parent interrupt controller(s)
|
|
this one is cascaded from
|
|
- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
|
|
node; valid values depend on the type of parent interrupt controller
|
|
|
|
If multiple reg ranges and interrupt-parent entries are present on an SMP
|
|
system, the driver will allow IRQ SMP affinity to be set up through the
|
|
/proc/irq/ interface. In the simplest possible configuration, only one
|
|
reg range and one interrupt-parent is needed.
|
|
|
|
The driver operates in native CPU endian by default, there is no support for
|
|
specifying an alternative endianness.
|
|
|
|
Example:
|
|
|
|
periph_intc: interrupt-controller@10000000 {
|
|
compatible = "brcm,bcm63168-l1-intc", "brcm,bcm6345-l1-intc";
|
|
reg = <0x10000020 0x20>,
|
|
<0x10000040 0x20>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
|
|
interrupt-parent = <&cpu_intc>;
|
|
interrupts = <2>, <3>;
|
|
};
|