forked from Minki/linux
2ef2a48925
After the Nomadik pin controller was force migrated to generic pin control bindings, some leftovers in the documentation need to be cleaned up. The code and device trees are already migrated. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
146 lines
3.9 KiB
Plaintext
146 lines
3.9 KiB
Plaintext
ST Ericsson Nomadik pinmux controller
|
|
|
|
Required properties:
|
|
- compatible: "stericsson,db8500-pinctrl", "stericsson,db8540-pinctrl",
|
|
"stericsson,stn8815-pinctrl"
|
|
- reg: Should contain the register physical address and length of the PRCMU.
|
|
|
|
Please refer to pinctrl-bindings.txt in this directory for details of the
|
|
common pinctrl bindings used by client devices, including the meaning of the
|
|
phrase "pin configuration node".
|
|
|
|
ST Ericsson's pin configuration nodes act as a container for an arbitrary number of
|
|
subnodes. Each of these subnodes represents some desired configuration for a
|
|
pin, a group, or a list of pins or groups. This configuration can include the
|
|
mux function to select on those pin(s)/group(s), and various pin configuration
|
|
parameters, such as input, output, pull up, pull down...
|
|
|
|
The name of each subnode is not important; all subnodes should be enumerated
|
|
and processed purely based on their content. The subnodes use the generic
|
|
pin multiplexing node layout from the standard pin control bindings
|
|
(see pinctrl-bindings.txt):
|
|
|
|
Required pin multiplexing subnode properties:
|
|
- function: A string containing the name of the function to mux to the
|
|
pin or group.
|
|
- groups : An array of strings. Each string contains the name of a pin
|
|
group that will be combined with the function to form a multiplexing
|
|
set-up.
|
|
|
|
Required pin configuration subnode properties:
|
|
- pins: A string array describing the pins affected by the configuration
|
|
in the node.
|
|
- ste,config: Handle of pin configuration node
|
|
(e.g. ste,config = <&slpm_in_wkup_pdis>)
|
|
|
|
- ste,input : <0/1/2>
|
|
0: input with no pull
|
|
1: input with pull up,
|
|
2: input with pull down,
|
|
|
|
- ste,output: <0/1/2>
|
|
0: output low,
|
|
1: output high,
|
|
2: output (value is not specified).
|
|
|
|
- ste,sleep: <0/1>
|
|
0: sleep mode disable,
|
|
1: sleep mode enable.
|
|
|
|
- ste,sleep-input: <0/1/2/3>
|
|
0: sleep input with no pull,
|
|
1: sleep input with pull up,
|
|
2: sleep input with pull down.
|
|
3: sleep input and keep last input configuration (no pull, pull up or pull down).
|
|
|
|
- ste,sleep-output: <0/1/2>
|
|
0: sleep output low,
|
|
1: sleep output high,
|
|
2: sleep output (value is not specified).
|
|
|
|
- ste,sleep-gpio: <0/1>
|
|
0: disable sleep gpio mode,
|
|
1: enable sleep gpio mode.
|
|
|
|
- ste,sleep-wakeup: <0/1>
|
|
0: wake-up detection enabled,
|
|
1: wake-up detection disabled.
|
|
|
|
- ste,sleep-pull-disable: <0/1>
|
|
0: GPIO pull-up or pull-down resistor is enabled, when pin is an input,
|
|
1: GPIO pull-up and pull-down resistor are disabled.
|
|
|
|
Example board file extract:
|
|
|
|
pinctrl@80157000 {
|
|
compatible = "stericsson,db8500-pinctrl";
|
|
reg = <0x80157000 0x2000>;
|
|
|
|
pinctrl-names = "default";
|
|
|
|
slpm_in_wkup_pdis: slpm_in_wkup_pdis {
|
|
ste,sleep = <1>;
|
|
ste,sleep-input = <3>;
|
|
ste,sleep-wakeup = <1>;
|
|
ste,sleep-pull-disable = <0>;
|
|
};
|
|
|
|
slpm_out_hi_wkup_pdis: slpm_out_hi_wkup_pdis {
|
|
ste,sleep = <1>;
|
|
ste,sleep-output = <1>;
|
|
ste,sleep-wakeup = <1>;
|
|
ste,sleep-pull-disable = <0>;
|
|
};
|
|
|
|
slpm_out_wkup_pdis: slpm_out_wkup_pdis {
|
|
ste,sleep = <1>;
|
|
ste,sleep-output = <2>;
|
|
ste,sleep-wakeup = <1>;
|
|
ste,sleep-pull-disable = <0>;
|
|
};
|
|
|
|
uart0 {
|
|
uart0_default_mux: uart0_mux {
|
|
u0_default_mux {
|
|
function = "u0";
|
|
pins = "u0_a_1";
|
|
};
|
|
};
|
|
uart0_default_mode: uart0_default {
|
|
uart0_default_cfg1 {
|
|
pins = "GPIO0", "GPIO2";
|
|
ste,input = <1>;
|
|
};
|
|
|
|
uart0_default_cfg2 {
|
|
pins = "GPIO1", "GPIO3";
|
|
ste,output = <1>;
|
|
};
|
|
};
|
|
uart0_sleep_mode: uart0_sleep {
|
|
uart0_sleep_cfg1 {
|
|
pins = "GPIO0", "GPIO2";
|
|
ste,config = <&slpm_in_wkup_pdis>;
|
|
};
|
|
uart0_sleep_cfg2 {
|
|
pins = "GPIO1";
|
|
ste,config = <&slpm_out_hi_wkup_pdis>;
|
|
};
|
|
uart0_sleep_cfg3 {
|
|
pins = "GPIO3";
|
|
ste,config = <&slpm_out_wkup_pdis>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
uart@80120000 {
|
|
compatible = "arm,pl011", "arm,primecell";
|
|
reg = <0x80120000 0x1000>;
|
|
interrupts = <0 11 0x4>;
|
|
|
|
pinctrl-names = "default","sleep";
|
|
pinctrl-0 = <&uart0_default_mux>, <&uart0_default_mode>;
|
|
pinctrl-1 = <&uart0_sleep_mode>;
|
|
};
|