bc6b1e7b86
This patch adds basic DT bindings for OMAP GPMC. The actual peripherals are instantiated from child nodes within the GPMC node, and the only type of device that is currently supported is NAND. Code was added to parse the generic GPMC timing parameters and some documentation with examples on how to use them. Successfully tested on an AM33xx board. Signed-off-by: Daniel Mack <zonque@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> [tony@atomide.com: updated to apply] Signed-off-by: Tony Lindgren <tony@atomide.com>
77 lines
1.9 KiB
Plaintext
77 lines
1.9 KiB
Plaintext
Device tree bindings for GPMC connected NANDs
|
|
|
|
GPMC connected NAND (found on OMAP boards) are represented as child nodes of
|
|
the GPMC controller with a name of "nand".
|
|
|
|
All timing relevant properties as well as generic gpmc child properties are
|
|
explained in a separate documents - please refer to
|
|
Documentation/devicetree/bindings/bus/ti-gpmc.txt
|
|
|
|
For NAND specific properties such as ECC modes or bus width, please refer to
|
|
Documentation/devicetree/bindings/mtd/nand.txt
|
|
|
|
|
|
Required properties:
|
|
|
|
- reg: The CS line the peripheral is connected to
|
|
|
|
Optional properties:
|
|
|
|
- nand-bus-width: Set this numeric value to 16 if the hardware
|
|
is wired that way. If not specified, a bus
|
|
width of 8 is assumed.
|
|
|
|
- ti,nand-ecc-opt: A string setting the ECC layout to use. One of:
|
|
|
|
"sw" Software method (default)
|
|
"hw" Hardware method
|
|
"hw-romcode" gpmc hamming mode method & romcode layout
|
|
"bch4" 4-bit BCH ecc code
|
|
"bch8" 8-bit BCH ecc code
|
|
|
|
For inline partiton table parsing (optional):
|
|
|
|
- #address-cells: should be set to 1
|
|
- #size-cells: should be set to 1
|
|
|
|
Example for an AM33xx board:
|
|
|
|
gpmc: gpmc@50000000 {
|
|
compatible = "ti,am3352-gpmc";
|
|
ti,hwmods = "gpmc";
|
|
reg = <0x50000000 0x1000000>;
|
|
interrupts = <100>;
|
|
gpmc,num-cs = <8>;
|
|
gpmc,num-waitpins = <2>;
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
ranges = <0 0 0x08000000 0x2000>; /* CS0: NAND */
|
|
|
|
nand@0,0 {
|
|
reg = <0 0 0>; /* CS0, offset 0 */
|
|
nand-bus-width = <16>;
|
|
ti,nand-ecc-opt = "bch8";
|
|
|
|
gpmc,sync-clk = <0>;
|
|
gpmc,cs-on = <0>;
|
|
gpmc,cs-rd-off = <44>;
|
|
gpmc,cs-wr-off = <44>;
|
|
gpmc,adv-on = <6>;
|
|
gpmc,adv-rd-off = <34>;
|
|
gpmc,adv-wr-off = <44>;
|
|
gpmc,we-off = <40>;
|
|
gpmc,oe-off = <54>;
|
|
gpmc,access = <64>;
|
|
gpmc,rd-cycle = <82>;
|
|
gpmc,wr-cycle = <82>;
|
|
gpmc,wr-access = <40>;
|
|
gpmc,wr-data-mux-bus = <0>;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
/* partitions go here */
|
|
};
|
|
};
|
|
|