forked from Minki/linux
447b0c7b93
This adds support for the mostly register-compatible SPICTRL cores from the GRLIB VHDL IP core library from Aeroflex Gaisler. They are normally running on SPARC. A different entry in of_fsl_spi_match matches this core and indicates a different hardware type that is used to set up different function pointers and special cases. The GRLIB core operates in cpu mode. The number of bits per word might be limited. There might be native chipselects selected via a slave select register. These differences to the FSL type cores, if present, are indicated by a capabilities register. Other register and function differences exists but are not relevant to the driver. Acked-by: Anton Vorontsov <anton@enomsg.org> Signed-off-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
55 lines
1.7 KiB
Plaintext
55 lines
1.7 KiB
Plaintext
* SPI (Serial Peripheral Interface)
|
|
|
|
Required properties:
|
|
- cell-index : QE SPI subblock index.
|
|
0: QE subblock SPI1
|
|
1: QE subblock SPI2
|
|
- compatible : should be "fsl,spi" or "aeroflexgaisler,spictrl".
|
|
- mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
|
|
- reg : Offset and length of the register set for the device
|
|
- interrupts : <a b> where a is the interrupt number and b is a
|
|
field that represents an encoding of the sense and level
|
|
information for the interrupt. This should be encoded based on
|
|
the information in section 2) depending on the type of interrupt
|
|
controller you have.
|
|
- interrupt-parent : the phandle for the interrupt controller that
|
|
services interrupts for this device.
|
|
- clock-frequency : input clock frequency to non FSL_SOC cores
|
|
|
|
Optional properties:
|
|
- gpios : specifies the gpio pins to be used for chipselects.
|
|
The gpios will be referred to as reg = <index> in the SPI child nodes.
|
|
If unspecified, a single SPI device without a chip select can be used.
|
|
|
|
Example:
|
|
spi@4c0 {
|
|
cell-index = <0>;
|
|
compatible = "fsl,spi";
|
|
reg = <4c0 40>;
|
|
interrupts = <82 0>;
|
|
interrupt-parent = <700>;
|
|
mode = "cpu";
|
|
gpios = <&gpio 18 1 // device reg=<0>
|
|
&gpio 19 1>; // device reg=<1>
|
|
};
|
|
|
|
|
|
* eSPI (Enhanced Serial Peripheral Interface)
|
|
|
|
Required properties:
|
|
- compatible : should be "fsl,mpc8536-espi".
|
|
- reg : Offset and length of the register set for the device.
|
|
- interrupts : should contain eSPI interrupt, the device has one interrupt.
|
|
- fsl,espi-num-chipselects : the number of the chipselect signals.
|
|
|
|
Example:
|
|
spi@110000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,mpc8536-espi";
|
|
reg = <0x110000 0x1000>;
|
|
interrupts = <53 0x2>;
|
|
interrupt-parent = <&mpic>;
|
|
fsl,espi-num-chipselects = <4>;
|
|
};
|