forked from Minki/linux
e0ee84ded7
per discussion at netconf/netdev: When we have an action that is capable of branching (example a policer), we can achieve a continuation of the action graph by programming a "continue" where we find an exact replica of the same filter rule with a lower priority and the remainder of the action graph. When you have 100s of thousands of filters which require such a feature it gets very inefficient to do two lookups. This patch completes a leftover feature of action codes. Its time has come. Example below where a user labels packets with a different skbmark on ingress of a port depending on whether they have/not exceeded the configured rate. This mark is then used to make further decisions on some egress port. #rate control, very low so we can easily see the effect sudo $TC actions add action police rate 1kbit burst 90k \ conform-exceed pipe/jump 2 index 10 # skbedit index 11 will be used if the user conforms sudo $TC actions add action skbedit mark 11 ok index 11 # skbedit index 12 will be used if the user does not conform sudo $TC actions add action skbedit mark 12 ok index 12 #lets bind the user .. sudo $TC filter add dev $ETH parent ffff: protocol ip prio 8 u32 \ match ip dst 127.0.0.8/32 flowid 1:10 \ action police index 10 \ action skbedit index 11 \ action skbedit index 12 #run a ping -f and see what happens.. # jhs@foobar:~$ sudo $TC -s filter ls dev $ETH parent ffff: protocol ip filter pref 8 u32 filter pref 8 u32 fh 800: ht divisor 1 filter pref 8 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:10 (rule hit 2800 success 1005) match 7f000008/ffffffff at 16 (success 1005 ) action order 1: police 0xa rate 1Kbit burst 23440b mtu 2Kb action pipe/jump 2 overhead 0b ref 2 bind 1 installed 207 sec used 122 sec Action statistics: Sent 84420 bytes 1005 pkt (dropped 0, overlimits 721 requeues 0) backlog 0b 0p requeues 0 action order 2: skbedit mark 11 pass index 11 ref 2 bind 1 installed 204 sec used 122 sec Action statistics: Sent 60564 bytes 721 pkt (dropped 0, overlimits 0 requeues 0) backlog 0b 0p requeues 0 action order 3: skbedit mark 12 pass index 12 ref 2 bind 1 installed 201 sec used 122 sec Action statistics: Sent 23856 bytes 284 pkt (dropped 0, overlimits 0 requeues 0) backlog 0b 0p requeues 0 Not bad, about 28% non-conforming packets.. Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
---|---|---|
.. | ||
act_api.c | ||
act_bpf.c | ||
act_connmark.c | ||
act_csum.c | ||
act_gact.c | ||
act_ife.c | ||
act_ipt.c | ||
act_meta_mark.c | ||
act_meta_skbprio.c | ||
act_meta_skbtcindex.c | ||
act_mirred.c | ||
act_nat.c | ||
act_pedit.c | ||
act_police.c | ||
act_sample.c | ||
act_simple.c | ||
act_skbedit.c | ||
act_skbmod.c | ||
act_tunnel_key.c | ||
act_vlan.c | ||
cls_api.c | ||
cls_basic.c | ||
cls_bpf.c | ||
cls_cgroup.c | ||
cls_flow.c | ||
cls_flower.c | ||
cls_fw.c | ||
cls_matchall.c | ||
cls_route.c | ||
cls_rsvp6.c | ||
cls_rsvp.c | ||
cls_rsvp.h | ||
cls_tcindex.c | ||
cls_u32.c | ||
em_canid.c | ||
em_cmp.c | ||
em_ipset.c | ||
em_meta.c | ||
em_nbyte.c | ||
em_text.c | ||
em_u32.c | ||
ematch.c | ||
Kconfig | ||
Makefile | ||
sch_api.c | ||
sch_atm.c | ||
sch_blackhole.c | ||
sch_cbq.c | ||
sch_choke.c | ||
sch_codel.c | ||
sch_drr.c | ||
sch_dsmark.c | ||
sch_fifo.c | ||
sch_fq_codel.c | ||
sch_fq.c | ||
sch_generic.c | ||
sch_gred.c | ||
sch_hfsc.c | ||
sch_hhf.c | ||
sch_htb.c | ||
sch_ingress.c | ||
sch_mq.c | ||
sch_mqprio.c | ||
sch_multiq.c | ||
sch_netem.c | ||
sch_pie.c | ||
sch_plug.c | ||
sch_prio.c | ||
sch_qfq.c | ||
sch_red.c | ||
sch_sfb.c | ||
sch_sfq.c | ||
sch_tbf.c | ||
sch_teql.c |