linux/drivers/cxl/Kconfig
Ben Widawsky 21e9f76733 cxl: Rename mem to pci
As the driver has undergone development, it's become clear that the
majority [entirety?] of the current functionality in mem.c is actually a
layer encapsulating functionality exposed through PCI based
interactions. This layer can be used either in isolation or to provide
functionality for higher level functionality.

CXL capabilities exist in a parallel domain to PCIe. CXL devices are
enumerable and controllable via "legacy" PCIe mechanisms; however, their
CXL capabilities are a superset of PCIe. For example, a CXL device may
be connected to a non-CXL capable PCIe root port, and therefore will not
be able to participate in CXL.mem or CXL.cache operations, but can still
be accessed through PCIe mechanisms for CXL.io operations.

To properly represent the PCI nature of this driver, and in preparation for
introducing a new driver for the CXL.mem / HDM decoder (Host-managed Device
Memory) capabilities of a CXL memory expander, rename mem.c to pci.c so that
mem.c is available for this new driver.

The result of the change is that there is a clear layering distinction
in the driver, and a systems administrator may load only the cxl_pci
module and gain access to such operations as, firmware update, offline
provisioning of devices, and error collection. In addition to freeing up
the file name for another purpose, there are two primary reasons this is
useful,
    1. Acting upon devices which don't have full CXL capabilities. This
       may happen for instance if the CXL device is connected in a CXL
       unaware part of the platform topology.
    2. Userspace-first provisioning for devices without kernel driver
       interference. This may be useful when provisioning a new device
       in a specific manner that might otherwise be blocked or prevented
       by the real CXL mem driver.

Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/20210526174413.802913-1-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2021-05-26 11:19:05 -07:00

49 lines
1.9 KiB
Plaintext

# SPDX-License-Identifier: GPL-2.0-only
menuconfig CXL_BUS
tristate "CXL (Compute Express Link) Devices Support"
depends on PCI
help
CXL is a bus that is electrically compatible with PCI Express, but
layers three protocols on that signalling (CXL.io, CXL.cache, and
CXL.mem). The CXL.cache protocol allows devices to hold cachelines
locally, the CXL.mem protocol allows devices to be fully coherent
memory targets, the CXL.io protocol is equivalent to PCI Express.
Say 'y' to enable support for the configuration and management of
devices supporting these protocols.
if CXL_BUS
config CXL_MEM
tristate "CXL.mem: Memory Devices"
help
The CXL.mem protocol allows a device to act as a provider of
"System RAM" and/or "Persistent Memory" that is fully coherent
as if the memory was attached to the typical CPU memory
controller.
Say 'y/m' to enable a driver that will attach to CXL.mem devices for
configuration and management primarily via the mailbox interface. See
Chapter 2.3 Type 3 CXL Device in the CXL 2.0 specification for more
details.
If unsure say 'm'.
config CXL_MEM_RAW_COMMANDS
bool "RAW Command Interface for Memory Devices"
depends on CXL_MEM
help
Enable CXL RAW command interface.
The CXL driver ioctl interface may assign a kernel ioctl command
number for each specification defined opcode. At any given point in
time the number of opcodes that the specification defines and a device
may implement may exceed the kernel's set of associated ioctl function
numbers. The mismatch is either by omission, specification is too new,
or by design. When prototyping new hardware, or developing / debugging
the driver it is useful to be able to submit any possible command to
the hardware, even commands that may crash the kernel due to their
potential impact to memory currently in use by the kernel.
If developing CXL hardware or the driver say Y, otherwise say N.
endif