linux/Documentation/serial/serial-iso7816.txt
Nicolas Ferre ad8c0eaa0a tty/serial_core: add ISO7816 infrastructure
Add the ISO7816 ioctl and associated accessors and data structure.
Drivers can then use this common implementation to handle ISO7816
(smart cards).

Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[ludovic.desroches@microchip.com: squash and rebase, removal of gpios, checkpatch fixes]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-02 13:38:55 -07:00

84 lines
2.4 KiB
Plaintext

ISO7816 SERIAL COMMUNICATIONS
1. INTRODUCTION
ISO/IEC7816 is a series of standards specifying integrated circuit cards (ICC)
also known as smart cards.
2. HARDWARE-RELATED CONSIDERATIONS
Some CPUs/UARTs (e.g., Microchip AT91) contain a built-in mode capable of
handling communication with a smart card.
For these microcontrollers, the Linux driver should be made capable of
working in both modes, and proper ioctls (see later) should be made
available at user-level to allow switching from one mode to the other, and
vice versa.
3. DATA STRUCTURES ALREADY AVAILABLE IN THE KERNEL
The Linux kernel provides the serial_iso7816 structure (see [1]) to handle
ISO7816 communications. This data structure is used to set and configure
ISO7816 parameters in ioctls.
Any driver for devices capable of working both as RS232 and ISO7816 should
implement the iso7816_config callback in the uart_port structure. The
serial_core calls iso7816_config to do the device specific part in response
to TIOCGISO7816 and TIOCSISO7816 ioctls (see below). The iso7816_config
callback receives a pointer to struct serial_iso7816.
4. USAGE FROM USER-LEVEL
From user-level, ISO7816 configuration can be get/set using the previous
ioctls. For instance, to set ISO7816 you can use the following code:
#include <linux/serial.h>
/* Include definition for ISO7816 ioctls: TIOCSISO7816 and TIOCGISO7816 */
#include <sys/ioctl.h>
/* Open your specific device (e.g., /dev/mydevice): */
int fd = open ("/dev/mydevice", O_RDWR);
if (fd < 0) {
/* Error handling. See errno. */
}
struct serial_iso7816 iso7816conf;
/* Reserved fields as to be zeroed */
memset(&iso7816conf, 0, sizeof(iso7816conf));
/* Enable ISO7816 mode: */
iso7816conf.flags |= SER_ISO7816_ENABLED;
/* Select the protocol: */
/* T=0 */
iso7816conf.flags |= SER_ISO7816_T(0);
/* or T=1 */
iso7816conf.flags |= SER_ISO7816_T(1);
/* Set the guard time: */
iso7816conf.tg = 2;
/* Set the clock frequency*/
iso7816conf.clk = 3571200;
/* Set transmission factors: */
iso7816conf.sc_fi = 372;
iso7816conf.sc_di = 1;
if (ioctl(fd_usart, TIOCSISO7816, &iso7816conf) < 0) {
/* Error handling. See errno. */
}
/* Use read() and write() syscalls here... */
/* Close the device when finished: */
if (close (fd) < 0) {
/* Error handling. See errno. */
}
5. REFERENCES
[1] include/uapi/linux/serial.h