forked from Minki/linux
a064a07f72
This patch adds the QSPI clock for stm32f469 discovery board. The gate mapping is a little bit different from stm32f429 soc. Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
96 lines
2.6 KiB
Plaintext
96 lines
2.6 KiB
Plaintext
STMicroelectronics STM32 Reset and Clock Controller
|
|
===================================================
|
|
|
|
The RCC IP is both a reset and a clock controller.
|
|
|
|
Please refer to clock-bindings.txt for common clock controller binding usage.
|
|
Please also refer to reset.txt for common reset controller binding usage.
|
|
|
|
Required properties:
|
|
- compatible: Should be:
|
|
"st,stm32f42xx-rcc"
|
|
"st,stm32f469-rcc"
|
|
- reg: should be register base and length as documented in the
|
|
datasheet
|
|
- #reset-cells: 1, see below
|
|
- #clock-cells: 2, device nodes should specify the clock in their "clocks"
|
|
property, containing a phandle to the clock device node, an index selecting
|
|
between gated clocks and other clocks and an index specifying the clock to
|
|
use.
|
|
|
|
Example:
|
|
|
|
rcc: rcc@40023800 {
|
|
#reset-cells = <1>;
|
|
#clock-cells = <2>
|
|
compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
|
|
reg = <0x40023800 0x400>;
|
|
};
|
|
|
|
Specifying gated clocks
|
|
=======================
|
|
|
|
The primary index must be set to 0.
|
|
|
|
The secondary index is the bit number within the RCC register bank, starting
|
|
from the first RCC clock enable register (RCC_AHB1ENR, address offset 0x30).
|
|
|
|
It is calculated as: index = register_offset / 4 * 32 + bit_offset.
|
|
Where bit_offset is the bit offset within the register (LSB is 0, MSB is 31).
|
|
|
|
To simplify the usage and to share bit definition with the reset and clock
|
|
drivers of the RCC IP, macros are available to generate the index in
|
|
human-readble format.
|
|
|
|
For STM32F4 series, the macro are available here:
|
|
- include/dt-bindings/mfd/stm32f4-rcc.h
|
|
|
|
Example:
|
|
|
|
/* Gated clock, AHB1 bit 0 (GPIOA) */
|
|
... {
|
|
clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOA)>
|
|
};
|
|
|
|
/* Gated clock, AHB2 bit 4 (CRYP) */
|
|
... {
|
|
clocks = <&rcc 0 STM32F4_AHB2_CLOCK(CRYP)>
|
|
};
|
|
|
|
Specifying other clocks
|
|
=======================
|
|
|
|
The primary index must be set to 1.
|
|
|
|
The secondary index is bound with the following magic numbers:
|
|
|
|
0 SYSTICK
|
|
1 FCLK
|
|
|
|
Example:
|
|
|
|
/* Misc clock, FCLK */
|
|
... {
|
|
clocks = <&rcc 1 STM32F4_APB1_CLOCK(TIM2)>
|
|
};
|
|
|
|
|
|
Specifying softreset control of devices
|
|
=======================================
|
|
|
|
Device nodes should specify the reset channel required in their "resets"
|
|
property, containing a phandle to the reset device node and an index specifying
|
|
which channel to use.
|
|
The index is the bit number within the RCC registers bank, starting from RCC
|
|
base address.
|
|
It is calculated as: index = register_offset / 4 * 32 + bit_offset.
|
|
Where bit_offset is the bit offset within the register.
|
|
For example, for CRC reset:
|
|
crc = AHB1RSTR_offset / 4 * 32 + CRCRST_bit_offset = 0x10 / 4 * 32 + 12 = 140
|
|
|
|
example:
|
|
|
|
timer2 {
|
|
resets = <&rcc STM32F4_APB1_RESET(TIM2)>;
|
|
};
|