forked from Minki/linux
d675d0bc47
Before we enable the MMU, we must ensure that the TTBR registers contain sane values. After the MMU has been enabled, we jump to the *virtual* address of the following function, so we also need to ensure that the SCTLR write has taken effect. This patch adds ISB instructions around the SCTLR write to ensure the visibility of the above. Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
106 lines
2.8 KiB
ArmAsm
106 lines
2.8 KiB
ArmAsm
#include <linux/linkage.h>
|
|
#include <linux/threads.h>
|
|
#include <asm/asm-offsets.h>
|
|
#include <asm/assembler.h>
|
|
#include <asm/glue-cache.h>
|
|
#include <asm/glue-proc.h>
|
|
#include <asm/system.h>
|
|
.text
|
|
|
|
/*
|
|
* Save CPU state for a suspend. This saves the CPU general purpose
|
|
* registers, and allocates space on the kernel stack to save the CPU
|
|
* specific registers and some other data for resume.
|
|
* r0 = suspend function arg0
|
|
* r1 = suspend function
|
|
*/
|
|
ENTRY(__cpu_suspend)
|
|
stmfd sp!, {r4 - r11, lr}
|
|
#ifdef MULTI_CPU
|
|
ldr r10, =processor
|
|
ldr r4, [r10, #CPU_SLEEP_SIZE] @ size of CPU sleep state
|
|
#else
|
|
ldr r4, =cpu_suspend_size
|
|
#endif
|
|
mov r5, sp @ current virtual SP
|
|
add r4, r4, #12 @ Space for pgd, virt sp, phys resume fn
|
|
sub sp, sp, r4 @ allocate CPU state on stack
|
|
stmfd sp!, {r0, r1} @ save suspend func arg and pointer
|
|
add r0, sp, #8 @ save pointer to save block
|
|
mov r1, r4 @ size of save block
|
|
mov r2, r5 @ virtual SP
|
|
ldr r3, =sleep_save_sp
|
|
#ifdef CONFIG_SMP
|
|
ALT_SMP(mrc p15, 0, lr, c0, c0, 5)
|
|
ALT_UP(mov lr, #0)
|
|
and lr, lr, #15
|
|
add r3, r3, lr, lsl #2
|
|
#endif
|
|
bl __cpu_suspend_save
|
|
adr lr, BSYM(cpu_suspend_abort)
|
|
ldmfd sp!, {r0, pc} @ call suspend fn
|
|
ENDPROC(__cpu_suspend)
|
|
.ltorg
|
|
|
|
cpu_suspend_abort:
|
|
ldmia sp!, {r1 - r3} @ pop phys pgd, virt SP, phys resume fn
|
|
teq r0, #0
|
|
moveq r0, #1 @ force non-zero value
|
|
mov sp, r2
|
|
ldmfd sp!, {r4 - r11, pc}
|
|
ENDPROC(cpu_suspend_abort)
|
|
|
|
/*
|
|
* r0 = control register value
|
|
*/
|
|
.align 5
|
|
.pushsection .idmap.text,"ax"
|
|
ENTRY(cpu_resume_mmu)
|
|
ldr r3, =cpu_resume_after_mmu
|
|
instr_sync
|
|
mcr p15, 0, r0, c1, c0, 0 @ turn on MMU, I-cache, etc
|
|
mrc p15, 0, r0, c0, c0, 0 @ read id reg
|
|
instr_sync
|
|
mov r0, r0
|
|
mov r0, r0
|
|
mov pc, r3 @ jump to virtual address
|
|
ENDPROC(cpu_resume_mmu)
|
|
.popsection
|
|
cpu_resume_after_mmu:
|
|
bl cpu_init @ restore the und/abt/irq banked regs
|
|
mov r0, #0 @ return zero on success
|
|
ldmfd sp!, {r4 - r11, pc}
|
|
ENDPROC(cpu_resume_after_mmu)
|
|
|
|
/*
|
|
* Note: Yes, part of the following code is located into the .data section.
|
|
* This is to allow sleep_save_sp to be accessed with a relative load
|
|
* while we can't rely on any MMU translation. We could have put
|
|
* sleep_save_sp in the .text section as well, but some setups might
|
|
* insist on it to be truly read-only.
|
|
*/
|
|
.data
|
|
.align
|
|
ENTRY(cpu_resume)
|
|
#ifdef CONFIG_SMP
|
|
adr r0, sleep_save_sp
|
|
ALT_SMP(mrc p15, 0, r1, c0, c0, 5)
|
|
ALT_UP(mov r1, #0)
|
|
and r1, r1, #15
|
|
ldr r0, [r0, r1, lsl #2] @ stack phys addr
|
|
#else
|
|
ldr r0, sleep_save_sp @ stack phys addr
|
|
#endif
|
|
setmode PSR_I_BIT | PSR_F_BIT | SVC_MODE, r1 @ set SVC, irqs off
|
|
@ load phys pgd, stack, resume fn
|
|
ARM( ldmia r0!, {r1, sp, pc} )
|
|
THUMB( ldmia r0!, {r1, r2, r3} )
|
|
THUMB( mov sp, r2 )
|
|
THUMB( bx r3 )
|
|
ENDPROC(cpu_resume)
|
|
|
|
sleep_save_sp:
|
|
.rept CONFIG_NR_CPUS
|
|
.long 0 @ preserve stack phys ptr here
|
|
.endr
|