forked from Minki/linux
770b6cb4d2
These devices are not available on other architectures, so let's limit them to omap. If the driver subsystem maintainers want to build test system wide changes without building for each target, it's easy to carry a test patch that just strips out the depends entries from Kconfig files. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
70 lines
1.8 KiB
Plaintext
70 lines
1.8 KiB
Plaintext
#
|
|
# 1-wire bus master configuration
|
|
#
|
|
|
|
menu "1-wire Bus Masters"
|
|
|
|
config W1_MASTER_MATROX
|
|
tristate "Matrox G400 transport layer for 1-wire"
|
|
depends on PCI
|
|
help
|
|
Say Y here if you want to communicate with your 1-wire devices
|
|
using Matrox's G400 GPIO pins.
|
|
|
|
This support is also available as a module. If so, the module
|
|
will be called matrox_w1.
|
|
|
|
config W1_MASTER_DS2490
|
|
tristate "DS2490 USB <-> W1 transport layer for 1-wire"
|
|
depends on USB
|
|
help
|
|
Say Y here if you want to have a driver for DS2490 based USB <-> W1 bridges,
|
|
for example DS9490*.
|
|
|
|
This support is also available as a module. If so, the module
|
|
will be called ds2490.
|
|
|
|
config W1_MASTER_DS2482
|
|
tristate "Maxim DS2482 I2C to 1-Wire bridge"
|
|
depends on I2C
|
|
help
|
|
If you say yes here you get support for the Maxim DS2482
|
|
I2C to 1-Wire bridge.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called ds2482.
|
|
|
|
config W1_MASTER_MXC
|
|
tristate "Freescale MXC 1-wire busmaster"
|
|
depends on W1 && ARCH_MXC
|
|
help
|
|
Say Y here to enable MXC 1-wire host
|
|
|
|
config W1_MASTER_DS1WM
|
|
tristate "Maxim DS1WM 1-wire busmaster"
|
|
depends on W1 && GENERIC_HARDIRQS
|
|
help
|
|
Say Y here to enable the DS1WM 1-wire driver, such as that
|
|
in HP iPAQ devices like h5xxx, h2200, and ASIC3-based like
|
|
hx4700.
|
|
|
|
config W1_MASTER_GPIO
|
|
tristate "GPIO 1-wire busmaster"
|
|
depends on GENERIC_GPIO
|
|
help
|
|
Say Y here if you want to communicate with your 1-wire devices using
|
|
GPIO pins. This driver uses the GPIO API to control the wire.
|
|
|
|
This support is also available as a module. If so, the module
|
|
will be called w1-gpio.
|
|
|
|
config HDQ_MASTER_OMAP
|
|
tristate "OMAP HDQ driver"
|
|
depends on ARCH_OMAP
|
|
help
|
|
Say Y here if you want support for the 1-wire or HDQ Interface
|
|
on an OMAP processor.
|
|
|
|
endmenu
|
|
|