forked from Minki/linux
fd39318806
The at24 driver allows to register I2C EEPROM chips using different vendor and devices, but the I2C subsystem does not take the vendor into account when matching using the I2C table since it only has device entries. But when matching using an OF table, both the vendor and device has to be taken into account so the driver defines only a set of compatible strings using the "atmel" vendor as a generic fallback for compatible I2C devices. So add this generic fallback to the device node compatible string to make the device to match the driver using the OF device ID table. Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
162 lines
3.0 KiB
Plaintext
162 lines
3.0 KiB
Plaintext
/*
|
|
* Digsy MTC board Device Tree Source
|
|
*
|
|
* Copyright (C) 2009 Semihalf
|
|
*
|
|
* Based on the CM5200 by M. Balakowicz
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License as published by the
|
|
* Free Software Foundation; either version 2 of the License, or (at your
|
|
* option) any later version.
|
|
*/
|
|
|
|
/include/ "mpc5200b.dtsi"
|
|
|
|
&gpt0 { gpio-controller; fsl,has-wdt; };
|
|
&gpt1 { gpio-controller; };
|
|
|
|
/ {
|
|
model = "intercontrol,digsy-mtc";
|
|
compatible = "intercontrol,digsy-mtc";
|
|
|
|
memory {
|
|
reg = <0x00000000 0x02000000>; // 32MB
|
|
};
|
|
|
|
soc5200@f0000000 {
|
|
rtc@800 {
|
|
status = "disabled";
|
|
};
|
|
|
|
spi@f00 {
|
|
msp430@0 {
|
|
compatible = "spidev";
|
|
spi-max-frequency = <32000>;
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
psc@2000 { // PSC1
|
|
status = "disabled";
|
|
};
|
|
|
|
psc@2200 { // PSC2
|
|
status = "disabled";
|
|
};
|
|
|
|
psc@2400 { // PSC3
|
|
status = "disabled";
|
|
};
|
|
|
|
psc@2600 { // PSC4
|
|
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
|
|
};
|
|
|
|
psc@2800 { // PSC5
|
|
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
|
|
};
|
|
|
|
psc@2c00 { // PSC6
|
|
status = "disabled";
|
|
};
|
|
|
|
ethernet@3000 {
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
mdio@3000 {
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
i2c@3d00 {
|
|
eeprom@50 {
|
|
compatible = "atmel,24c08";
|
|
reg = <0x50>;
|
|
};
|
|
|
|
rtc@56 {
|
|
compatible = "mc,rv3029c2";
|
|
reg = <0x56>;
|
|
};
|
|
|
|
rtc@68 {
|
|
compatible = "dallas,ds1339";
|
|
reg = <0x68>;
|
|
};
|
|
};
|
|
|
|
i2c@3d40 {
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
pci@f0000d00 {
|
|
interrupt-map-mask = <0xf800 0 0 7>;
|
|
interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3
|
|
0xc000 0 0 2 &mpc5200_pic 0 0 3
|
|
0xc000 0 0 3 &mpc5200_pic 0 0 3
|
|
0xc000 0 0 4 &mpc5200_pic 0 0 3>;
|
|
clock-frequency = <0>; // From boot loader
|
|
interrupts = <2 8 0 2 9 0 2 10 0>;
|
|
bus-range = <0 0>;
|
|
ranges = <0x42000000 0 0x80000000 0x80000000 0 0x10000000
|
|
0x02000000 0 0x90000000 0x90000000 0 0x10000000
|
|
0x01000000 0 0x00000000 0xa0000000 0 0x01000000>;
|
|
};
|
|
|
|
localbus {
|
|
ranges = <0 0 0xff000000 0x1000000
|
|
4 0 0x60000000 0x0001000>;
|
|
|
|
// 16-bit flash device at LocalPlus Bus CS0
|
|
flash@0,0 {
|
|
compatible = "cfi-flash";
|
|
reg = <0 0 0x1000000>;
|
|
bank-width = <2>;
|
|
device-width = <2>;
|
|
#size-cells = <1>;
|
|
#address-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "kernel";
|
|
reg = <0x0 0x00200000>;
|
|
};
|
|
partition@200000 {
|
|
label = "root";
|
|
reg = <0x00200000 0x00300000>;
|
|
};
|
|
partition@500000 {
|
|
label = "user";
|
|
reg = <0x00500000 0x00a00000>;
|
|
};
|
|
partition@f00000 {
|
|
label = "u-boot";
|
|
reg = <0x00f00000 0x100000>;
|
|
};
|
|
};
|
|
|
|
can@4,0 {
|
|
compatible = "nxp,sja1000";
|
|
reg = <4 0x000 0x80>;
|
|
nxp,external-clock-frequency = <24000000>;
|
|
interrupts = <1 2 3>; // Level-low
|
|
};
|
|
|
|
can@4,100 {
|
|
compatible = "nxp,sja1000";
|
|
reg = <4 0x100 0x80>;
|
|
nxp,external-clock-frequency = <24000000>;
|
|
interrupts = <1 2 3>; // Level-low
|
|
};
|
|
|
|
serial@4,200 {
|
|
compatible = "nxp,sc28l92";
|
|
reg = <4 0x200 0x10>;
|
|
interrupts = <1 3 3>;
|
|
};
|
|
};
|
|
};
|