forked from Minki/linux
e116c0545d
In order to support advanced AAD timings, add these properties to the DT GPMC bindings. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Roger Quadros <rogerq@ti.com>
136 lines
5.3 KiB
Plaintext
136 lines
5.3 KiB
Plaintext
Device tree bindings for OMAP general purpose memory controllers (GPMC)
|
|
|
|
The actual devices are instantiated from the child nodes of a GPMC node.
|
|
|
|
Required properties:
|
|
|
|
- compatible: Should be set to one of the following:
|
|
|
|
ti,omap2420-gpmc (omap2420)
|
|
ti,omap2430-gpmc (omap2430)
|
|
ti,omap3430-gpmc (omap3430 & omap3630)
|
|
ti,omap4430-gpmc (omap4430 & omap4460 & omap543x)
|
|
ti,am3352-gpmc (am335x devices)
|
|
|
|
- reg: A resource specifier for the register space
|
|
(see the example below)
|
|
- ti,hwmods: Should be set to "ti,gpmc" until the DT transition is
|
|
completed.
|
|
- #address-cells: Must be set to 2 to allow memory address translation
|
|
- #size-cells: Must be set to 1 to allow CS address passing
|
|
- gpmc,num-cs: The maximum number of chip-select lines that controller
|
|
can support.
|
|
- gpmc,num-waitpins: The maximum number of wait pins that controller can
|
|
support.
|
|
- ranges: Must be set up to reflect the memory layout with four
|
|
integer values for each chip-select line in use:
|
|
|
|
<cs-number> 0 <physical address of mapping> <size>
|
|
|
|
Currently, calculated values derived from the contents
|
|
of the per-CS register GPMC_CONFIG7 (as set up by the
|
|
bootloader) are used for the physical address decoding.
|
|
As this will change in the future, filling correct
|
|
values here is a requirement.
|
|
|
|
Timing properties for child nodes. All are optional and default to 0.
|
|
|
|
- gpmc,sync-clk-ps: Minimum clock period for synchronous mode, in picoseconds
|
|
|
|
Chip-select signal timings (in nanoseconds) corresponding to GPMC_CONFIG2:
|
|
- gpmc,cs-on-ns: Assertion time
|
|
- gpmc,cs-rd-off-ns: Read deassertion time
|
|
- gpmc,cs-wr-off-ns: Write deassertion time
|
|
|
|
ADV signal timings (in nanoseconds) corresponding to GPMC_CONFIG3:
|
|
- gpmc,adv-on-ns: Assertion time
|
|
- gpmc,adv-rd-off-ns: Read deassertion time
|
|
- gpmc,adv-wr-off-ns: Write deassertion time
|
|
- gpmc,adv-aad-mux-on-ns: Assertion time for AAD
|
|
- gpmc,adv-aad-mux-rd-off-ns: Read deassertion time for AAD
|
|
- gpmc,adv-aad-mux-wr-off-ns: Write deassertion time for AAD
|
|
|
|
WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
|
|
- gpmc,we-on-ns Assertion time
|
|
- gpmc,we-off-ns: Deassertion time
|
|
|
|
OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
|
|
- gpmc,oe-on-ns: Assertion time
|
|
- gpmc,oe-off-ns: Deassertion time
|
|
- gpmc,oe-aad-mux-on-ns: Assertion time for AAD
|
|
- gpmc,oe-aad-mux-off-ns: Deassertion time for AAD
|
|
|
|
Access time and cycle time timings (in nanoseconds) corresponding to
|
|
GPMC_CONFIG5:
|
|
- gpmc,page-burst-access-ns: Multiple access word delay
|
|
- gpmc,access-ns: Start-cycle to first data valid delay
|
|
- gpmc,rd-cycle-ns: Total read cycle time
|
|
- gpmc,wr-cycle-ns: Total write cycle time
|
|
- gpmc,bus-turnaround-ns: Turn-around time between successive accesses
|
|
- gpmc,cycle2cycle-delay-ns: Delay between chip-select pulses
|
|
- gpmc,clk-activation-ns: GPMC clock activation time
|
|
- gpmc,wait-monitoring-ns: Start of wait monitoring with regard to valid
|
|
data
|
|
|
|
Boolean timing parameters. If property is present parameter enabled and
|
|
disabled if omitted:
|
|
- gpmc,adv-extra-delay: ADV signal is delayed by half GPMC clock
|
|
- gpmc,cs-extra-delay: CS signal is delayed by half GPMC clock
|
|
- gpmc,cycle2cycle-diffcsen: Add "cycle2cycle-delay" between successive
|
|
accesses to a different CS
|
|
- gpmc,cycle2cycle-samecsen: Add "cycle2cycle-delay" between successive
|
|
accesses to the same CS
|
|
- gpmc,oe-extra-delay: OE signal is delayed by half GPMC clock
|
|
- gpmc,we-extra-delay: WE signal is delayed by half GPMC clock
|
|
- gpmc,time-para-granularity: Multiply all access times by 2
|
|
|
|
The following are only applicable to OMAP3+ and AM335x:
|
|
- gpmc,wr-access-ns: In synchronous write mode, for single or
|
|
burst accesses, defines the number of
|
|
GPMC_FCLK cycles from start access time
|
|
to the GPMC_CLK rising edge used by the
|
|
memory device for the first data capture.
|
|
- gpmc,wr-data-mux-bus-ns: In address-data multiplex mode, specifies
|
|
the time when the first data is driven on
|
|
the address-data bus.
|
|
|
|
GPMC chip-select settings properties for child nodes. All are optional.
|
|
|
|
- gpmc,burst-length Page/burst length. Must be 4, 8 or 16.
|
|
- gpmc,burst-wrap Enables wrap bursting
|
|
- gpmc,burst-read Enables read page/burst mode
|
|
- gpmc,burst-write Enables write page/burst mode
|
|
- gpmc,device-width Total width of device(s) connected to a GPMC
|
|
chip-select in bytes. The GPMC supports 8-bit
|
|
and 16-bit devices and so this property must be
|
|
1 or 2.
|
|
- gpmc,mux-add-data Address and data multiplexing configuration.
|
|
Valid values are 1 for address-address-data
|
|
multiplexing mode and 2 for address-data
|
|
multiplexing mode.
|
|
- gpmc,sync-read Enables synchronous read. Defaults to asynchronous
|
|
is this is not set.
|
|
- gpmc,sync-write Enables synchronous writes. Defaults to asynchronous
|
|
is this is not set.
|
|
- gpmc,wait-pin Wait-pin used by client. Must be less than
|
|
"gpmc,num-waitpins".
|
|
- gpmc,wait-on-read Enables wait monitoring on reads.
|
|
- gpmc,wait-on-write Enables wait monitoring on writes.
|
|
|
|
Example for an AM33xx board:
|
|
|
|
gpmc: gpmc@50000000 {
|
|
compatible = "ti,am3352-gpmc";
|
|
ti,hwmods = "gpmc";
|
|
reg = <0x50000000 0x2000>;
|
|
interrupts = <100>;
|
|
|
|
gpmc,num-cs = <8>;
|
|
gpmc,num-waitpins = <2>;
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
|
|
|
|
/* child nodes go here */
|
|
};
|