linux/drivers/net/sky2.c
shemminger@osdl.org 2224795d7e [PATCH] sky2: dual port tx completion
Sometimes on dual port cards, one tx complete may cover both
ports. To handle that rearrange poll routine to lookup at
end.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-12-01 02:20:20 -05:00

3137 lines
82 KiB
C

/*
* New driver for Marvell Yukon 2 chipset.
* Based on earlier sk98lin, and skge driver.
*
* This driver intentionally does not support all the features
* of the original driver such as link fail-over and link management because
* those should be done at higher levels.
*
* Copyright (C) 2005 Stephen Hemminger <shemminger@osdl.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
/*
* TODO
* - coalescing setting?
*
* TOTEST
* - speed setting
* - suspend/resume
*/
#include <linux/config.h>
#include <linux/crc32.h>
#include <linux/kernel.h>
#include <linux/version.h>
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/dma-mapping.h>
#include <linux/etherdevice.h>
#include <linux/ethtool.h>
#include <linux/pci.h>
#include <linux/ip.h>
#include <linux/tcp.h>
#include <linux/in.h>
#include <linux/delay.h>
#include <linux/if_vlan.h>
#include <linux/mii.h>
#include <asm/irq.h>
#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
#define SKY2_VLAN_TAG_USED 1
#endif
#include "sky2.h"
#define DRV_NAME "sky2"
#define DRV_VERSION "0.7"
#define PFX DRV_NAME " "
/*
* The Yukon II chipset takes 64 bit command blocks (called list elements)
* that are organized into three (receive, transmit, status) different rings
* similar to Tigon3. A transmit can require several elements;
* a receive requires one (or two if using 64 bit dma).
*/
#define is_ec_a1(hw) \
unlikely((hw)->chip_id == CHIP_ID_YUKON_EC && \
(hw)->chip_rev == CHIP_REV_YU_EC_A1)
#define RX_LE_SIZE 512
#define RX_LE_BYTES (RX_LE_SIZE*sizeof(struct sky2_rx_le))
#define RX_MAX_PENDING (RX_LE_SIZE/2 - 2)
#define RX_DEF_PENDING RX_MAX_PENDING
#define RX_COPY_THRESHOLD 256
#define TX_RING_SIZE 512
#define TX_DEF_PENDING (TX_RING_SIZE - 1)
#define TX_MIN_PENDING 64
#define MAX_SKB_TX_LE (4 + 2*MAX_SKB_FRAGS)
#define STATUS_RING_SIZE 2048 /* 2 ports * (TX + 2*RX) */
#define STATUS_LE_BYTES (STATUS_RING_SIZE*sizeof(struct sky2_status_le))
#define ETH_JUMBO_MTU 9000
#define TX_WATCHDOG (5 * HZ)
#define NAPI_WEIGHT 64
#define PHY_RETRIES 1000
static const u32 default_msg =
NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK
| NETIF_MSG_TIMER | NETIF_MSG_TX_ERR | NETIF_MSG_RX_ERR
| NETIF_MSG_IFUP | NETIF_MSG_IFDOWN | NETIF_MSG_INTR;
static int debug = -1; /* defaults above */
module_param(debug, int, 0);
MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
static const struct pci_device_id sky2_id_table[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) },
{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) },
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b00) },
{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b01) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4340) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4341) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4342) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4343) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4344) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4345) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4346) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4347) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4350) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4351) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4352) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4360) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4361) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4362) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4363) },
{ 0 }
};
MODULE_DEVICE_TABLE(pci, sky2_id_table);
/* Avoid conditionals by using array */
static const unsigned txqaddr[] = { Q_XA1, Q_XA2 };
static const unsigned rxqaddr[] = { Q_R1, Q_R2 };
static const char *yukon_name[] = {
[CHIP_ID_YUKON_LITE - CHIP_ID_YUKON] = "Lite", /* 0xb0 */
[CHIP_ID_YUKON_LP - CHIP_ID_YUKON] = "LP", /* 0xb2 */
[CHIP_ID_YUKON_XL - CHIP_ID_YUKON] = "XL", /* 0xb3 */
[CHIP_ID_YUKON_EC_U - CHIP_ID_YUKON] = "EC Ultra", /* 0xb4 */
[CHIP_ID_YUKON_EC - CHIP_ID_YUKON] = "EC", /* 0xb6 */
[CHIP_ID_YUKON_FE - CHIP_ID_YUKON] = "FE", /* 0xb7 */
};
/* Access to external PHY */
static int gm_phy_write(struct sky2_hw *hw, unsigned port, u16 reg, u16 val)
{
int i;
gma_write16(hw, port, GM_SMI_DATA, val);
gma_write16(hw, port, GM_SMI_CTRL,
GM_SMI_CT_PHY_AD(PHY_ADDR_MARV) | GM_SMI_CT_REG_AD(reg));
for (i = 0; i < PHY_RETRIES; i++) {
if (!(gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_BUSY))
return 0;
udelay(1);
}
printk(KERN_WARNING PFX "%s: phy write timeout\n", hw->dev[port]->name);
return -ETIMEDOUT;
}
static int __gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg, u16 *val)
{
int i;
gma_write16(hw, port, GM_SMI_CTRL, GM_SMI_CT_PHY_AD(PHY_ADDR_MARV)
| GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD);
for (i = 0; i < PHY_RETRIES; i++) {
if (gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_RD_VAL) {
*val = gma_read16(hw, port, GM_SMI_DATA);
return 0;
}
udelay(1);
}
return -ETIMEDOUT;
}
static u16 gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg)
{
u16 v;
if (__gm_phy_read(hw, port, reg, &v) != 0)
printk(KERN_WARNING PFX "%s: phy read timeout\n", hw->dev[port]->name);
return v;
}
static int sky2_set_power_state(struct sky2_hw *hw, pci_power_t state)
{
u16 power_control;
u32 reg1;
int vaux;
int ret = 0;
pr_debug("sky2_set_power_state %d\n", state);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_PMC, &power_control);
vaux = (sky2_read8(hw, B0_CTST) & Y2_VAUX_AVAIL) &&
(power_control & PCI_PM_CAP_PME_D3cold);
pci_read_config_word(hw->pdev, hw->pm_cap + PCI_PM_CTRL, &power_control);
power_control |= PCI_PM_CTRL_PME_STATUS;
power_control &= ~(PCI_PM_CTRL_STATE_MASK);
switch (state) {
case PCI_D0:
/* switch power to VCC (WA for VAUX problem) */
sky2_write8(hw, B0_POWER_CTRL,
PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON);
/* disable Core Clock Division, */
sky2_write32(hw, B2_Y2_CLK_CTRL, Y2_CLK_DIV_DIS);
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
/* enable bits are inverted */
sky2_write8(hw, B2_Y2_CLK_GATE,
Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS |
Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS |
Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS);
else
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
/* Turn off phy power saving */
pci_read_config_dword(hw->pdev, PCI_DEV_REG1, &reg1);
reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
/* looks like this XL is back asswards .. */
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) {
reg1 |= PCI_Y2_PHY1_COMA;
if (hw->ports > 1)
reg1 |= PCI_Y2_PHY2_COMA;
}
pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1);
break;
case PCI_D3hot:
case PCI_D3cold:
/* Turn on phy power saving */
pci_read_config_dword(hw->pdev, PCI_DEV_REG1, &reg1);
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
else
reg1 |= (PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1);
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
else
/* enable bits are inverted */
sky2_write8(hw, B2_Y2_CLK_GATE,
Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS |
Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS |
Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS);
/* switch power to VAUX */
if (vaux && state != PCI_D3cold)
sky2_write8(hw, B0_POWER_CTRL,
(PC_VAUX_ENA | PC_VCC_ENA |
PC_VAUX_ON | PC_VCC_OFF));
break;
default:
printk(KERN_ERR PFX "Unknown power state %d\n", state);
ret = -1;
}
pci_write_config_byte(hw->pdev, hw->pm_cap + PCI_PM_CTRL, power_control);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
return ret;
}
static void sky2_phy_reset(struct sky2_hw *hw, unsigned port)
{
u16 reg;
/* disable all GMAC IRQ's */
sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0);
/* disable PHY IRQs */
gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
gma_write16(hw, port, GM_MC_ADDR_H1, 0); /* clear MC hash */
gma_write16(hw, port, GM_MC_ADDR_H2, 0);
gma_write16(hw, port, GM_MC_ADDR_H3, 0);
gma_write16(hw, port, GM_MC_ADDR_H4, 0);
reg = gma_read16(hw, port, GM_RX_CTRL);
reg |= GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA;
gma_write16(hw, port, GM_RX_CTRL, reg);
}
static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
{
struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
u16 ctrl, ct1000, adv, pg, ledctrl, ledover;
if (sky2->autoneg == AUTONEG_ENABLE && hw->chip_id != CHIP_ID_YUKON_XL) {
u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL);
ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK |
PHY_M_EC_MAC_S_MSK);
ectrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ);
if (hw->chip_id == CHIP_ID_YUKON_EC)
ectrl |= PHY_M_EC_DSC_2(2) | PHY_M_EC_DOWN_S_ENA;
else
ectrl |= PHY_M_EC_M_DSC(2) | PHY_M_EC_S_DSC(3);
gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, ectrl);
}
ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
if (hw->copper) {
if (hw->chip_id == CHIP_ID_YUKON_FE) {
/* enable automatic crossover */
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1;
} else {
/* disable energy detect */
ctrl &= ~PHY_M_PC_EN_DET_MSK;
/* enable automatic crossover */
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO);
if (sky2->autoneg == AUTONEG_ENABLE &&
hw->chip_id == CHIP_ID_YUKON_XL) {
ctrl &= ~PHY_M_PC_DSC_MSK;
ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
}
}
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
} else {
/* workaround for deviation #4.88 (CRC errors) */
/* disable Automatic Crossover */
ctrl &= ~PHY_M_PC_MDIX_MSK;
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
if (hw->chip_id == CHIP_ID_YUKON_XL) {
/* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
ctrl &= ~PHY_M_MAC_MD_MSK;
ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX);
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
/* select page 1 to access Fiber registers */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 1);
}
}
ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
if (sky2->autoneg == AUTONEG_DISABLE)
ctrl &= ~PHY_CT_ANE;
else
ctrl |= PHY_CT_ANE;
ctrl |= PHY_CT_RESET;
gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
ctrl = 0;
ct1000 = 0;
adv = PHY_AN_CSMA;
if (sky2->autoneg == AUTONEG_ENABLE) {
if (hw->copper) {
if (sky2->advertising & ADVERTISED_1000baseT_Full)
ct1000 |= PHY_M_1000C_AFD;
if (sky2->advertising & ADVERTISED_1000baseT_Half)
ct1000 |= PHY_M_1000C_AHD;
if (sky2->advertising & ADVERTISED_100baseT_Full)
adv |= PHY_M_AN_100_FD;
if (sky2->advertising & ADVERTISED_100baseT_Half)
adv |= PHY_M_AN_100_HD;
if (sky2->advertising & ADVERTISED_10baseT_Full)
adv |= PHY_M_AN_10_FD;
if (sky2->advertising & ADVERTISED_10baseT_Half)
adv |= PHY_M_AN_10_HD;
} else /* special defines for FIBER (88E1011S only) */
adv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD;
/* Set Flow-control capabilities */
if (sky2->tx_pause && sky2->rx_pause)
adv |= PHY_AN_PAUSE_CAP; /* symmetric */
else if (sky2->rx_pause && !sky2->tx_pause)
adv |= PHY_AN_PAUSE_ASYM | PHY_AN_PAUSE_CAP;
else if (!sky2->rx_pause && sky2->tx_pause)
adv |= PHY_AN_PAUSE_ASYM; /* local */
/* Restart Auto-negotiation */
ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
} else {
/* forced speed/duplex settings */
ct1000 = PHY_M_1000C_MSE;
if (sky2->duplex == DUPLEX_FULL)
ctrl |= PHY_CT_DUP_MD;
switch (sky2->speed) {
case SPEED_1000:
ctrl |= PHY_CT_SP1000;
break;
case SPEED_100:
ctrl |= PHY_CT_SP100;
break;
}
ctrl |= PHY_CT_RESET;
}
if (hw->chip_id != CHIP_ID_YUKON_FE)
gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000);
gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv);
gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
/* Setup Phy LED's */
ledctrl = PHY_M_LED_PULS_DUR(PULS_170MS);
ledover = 0;
switch (hw->chip_id) {
case CHIP_ID_YUKON_FE:
/* on 88E3082 these bits are at 11..9 (shifted left) */
ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) << 1;
ctrl = gm_phy_read(hw, port, PHY_MARV_FE_LED_PAR);
/* delete ACT LED control bits */
ctrl &= ~PHY_M_FELP_LED1_MSK;
/* change ACT LED control to blink mode */
ctrl |= PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_ACT_BL);
gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl);
break;
case CHIP_ID_YUKON_XL:
pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
/* select page 3 to access LED control register */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
/* set LED Function Control register */
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */
PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */
PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */
/* set Polarity Control register */
gm_phy_write(hw, port, PHY_MARV_PHY_STAT,
(PHY_M_POLC_LS1_P_MIX(4) |
PHY_M_POLC_IS0_P_MIX(4) |
PHY_M_POLC_LOS_CTRL(2) |
PHY_M_POLC_INIT_CTRL(2) |
PHY_M_POLC_STA1_CTRL(2) |
PHY_M_POLC_STA0_CTRL(2)));
/* restore page register */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
break;
default:
/* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */
ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL;
/* turn off the Rx LED (LED_RX) */
ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
}
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
/* turn on 100 Mbps LED (LED_LINK100) */
ledover |= PHY_M_LED_MO_100(MO_LED_ON);
}
if (ledover)
gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
/* Enable phy interrupt on auto-negotiation complete (or link up) */
if (sky2->autoneg == AUTONEG_ENABLE)
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL);
else
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
}
static void sky2_mac_init(struct sky2_hw *hw, unsigned port)
{
struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
u16 reg;
int i;
const u8 *addr = hw->dev[port]->dev_addr;
sky2_write32(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
sky2_write32(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR|GPC_ENA_PAUSE);
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR);
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 && port == 1) {
/* WA DEV_472 -- looks like crossed wires on port 2 */
/* clear GMAC 1 Control reset */
sky2_write8(hw, SK_REG(0, GMAC_CTRL), GMC_RST_CLR);
do {
sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_SET);
sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_CLR);
} while (gm_phy_read(hw, 1, PHY_MARV_ID0) != PHY_MARV_ID0_VAL ||
gm_phy_read(hw, 1, PHY_MARV_ID1) != PHY_MARV_ID1_Y2 ||
gm_phy_read(hw, 1, PHY_MARV_INT_MASK) != 0);
}
if (sky2->autoneg == AUTONEG_DISABLE) {
reg = gma_read16(hw, port, GM_GP_CTRL);
reg |= GM_GPCR_AU_ALL_DIS;
gma_write16(hw, port, GM_GP_CTRL, reg);
gma_read16(hw, port, GM_GP_CTRL);
switch (sky2->speed) {
case SPEED_1000:
reg |= GM_GPCR_SPEED_1000;
/* fallthru */
case SPEED_100:
reg |= GM_GPCR_SPEED_100;
}
if (sky2->duplex == DUPLEX_FULL)
reg |= GM_GPCR_DUP_FULL;
} else
reg = GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100 | GM_GPCR_DUP_FULL;
if (!sky2->tx_pause && !sky2->rx_pause) {
sky2_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
reg |=
GM_GPCR_FC_TX_DIS | GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
} else if (sky2->tx_pause && !sky2->rx_pause) {
/* disable Rx flow-control */
reg |= GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS;
}
gma_write16(hw, port, GM_GP_CTRL, reg);
sky2_read16(hw, SK_REG(port, GMAC_IRQ_SRC));
spin_lock_bh(&hw->phy_lock);
sky2_phy_init(hw, port);
spin_unlock_bh(&hw->phy_lock);
/* MIB clear */
reg = gma_read16(hw, port, GM_PHY_ADDR);
gma_write16(hw, port, GM_PHY_ADDR, reg | GM_PAR_MIB_CLR);
for (i = 0; i < GM_MIB_CNT_SIZE; i++)
gma_read16(hw, port, GM_MIB_CNT_BASE + 8 * i);
gma_write16(hw, port, GM_PHY_ADDR, reg);
/* transmit control */
gma_write16(hw, port, GM_TX_CTRL, TX_COL_THR(TX_COL_DEF));
/* receive control reg: unicast + multicast + no FCS */
gma_write16(hw, port, GM_RX_CTRL,
GM_RXCR_UCF_ENA | GM_RXCR_CRC_DIS | GM_RXCR_MCF_ENA);
/* transmit flow control */
gma_write16(hw, port, GM_TX_FLOW_CTRL, 0xffff);
/* transmit parameter */
gma_write16(hw, port, GM_TX_PARAM,
TX_JAM_LEN_VAL(TX_JAM_LEN_DEF) |
TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) |
TX_IPG_JAM_DATA(TX_IPG_JAM_DEF) |
TX_BACK_OFF_LIM(TX_BOF_LIM_DEF));
/* serial mode register */
reg = DATA_BLIND_VAL(DATA_BLIND_DEF) |
GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
if (hw->dev[port]->mtu > ETH_DATA_LEN)
reg |= GM_SMOD_JUMBO_ENA;
gma_write16(hw, port, GM_SERIAL_MODE, reg);
/* virtual address for data */
gma_set_addr(hw, port, GM_SRC_ADDR_2L, addr);
/* physical address: used for pause frames */
gma_set_addr(hw, port, GM_SRC_ADDR_1L, addr);
/* ignore counter overflows */
gma_write16(hw, port, GM_TX_IRQ_MSK, 0);
gma_write16(hw, port, GM_RX_IRQ_MSK, 0);
gma_write16(hw, port, GM_TR_IRQ_MSK, 0);
/* Configure Rx MAC FIFO */
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR);
sky2_write16(hw, SK_REG(port, RX_GMF_CTRL_T),
GMF_RX_CTRL_DEF);
/* Flush Rx MAC FIFO on any flow control or error */
sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), GMR_FS_ANY_ERR);
/* Set threshold to 0xa (64 bytes)
* ASF disabled so no need to do WA dev #4.30
*/
sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF);
/* Configure Tx MAC FIFO */
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
sky2_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON);
if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8);
sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8);
if (hw->dev[port]->mtu > ETH_DATA_LEN) {
/* set Tx GMAC FIFO Almost Empty Threshold */
sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR), 0x180);
/* Disable Store & Forward mode for TX */
sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_DIS);
}
}
}
static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, size_t len)
{
u32 end;
start /= 8;
len /= 8;
end = start + len - 1;
sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR);
sky2_write32(hw, RB_ADDR(q, RB_START), start);
sky2_write32(hw, RB_ADDR(q, RB_END), end);
sky2_write32(hw, RB_ADDR(q, RB_WP), start);
sky2_write32(hw, RB_ADDR(q, RB_RP), start);
if (q == Q_R1 || q == Q_R2) {
u32 rxup, rxlo;
rxlo = len/2;
rxup = rxlo + len/4;
/* Set thresholds on receive queue's */
sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), rxup);
sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), rxlo);
} else {
/* Enable store & forward on Tx queue's because
* Tx FIFO is only 1K on Yukon
*/
sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_STFWD);
}
sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_OP_MD);
sky2_read8(hw, RB_ADDR(q, RB_CTRL));
}
/* Setup Bus Memory Interface */
static void sky2_qset(struct sky2_hw *hw, u16 q, u32 wm)
{
sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_RESET);
sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_OPER_INIT);
sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_FIFO_OP_ON);
sky2_write32(hw, Q_ADDR(q, Q_WM), wm);
}
/* Setup prefetch unit registers. This is the interface between
* hardware and driver list elements
*/
static inline void sky2_prefetch_init(struct sky2_hw *hw, u32 qaddr,
u64 addr, u32 last)
{
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_CLR);
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_HI), addr >> 32);
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_LO), (u32) addr);
sky2_write16(hw, Y2_QADDR(qaddr, PREF_UNIT_LAST_IDX), last);
sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_OP_ON);
sky2_read32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL));
}
static inline struct sky2_tx_le *get_tx_le(struct sky2_port *sky2)
{
struct sky2_tx_le *le = sky2->tx_le + sky2->tx_prod;
sky2->tx_prod = (sky2->tx_prod + 1) % TX_RING_SIZE;
return le;
}
/*
* This is a workaround code taken from SysKonnect sk98lin driver
* to deal with chip bug on Yukon EC rev 0 in the wraparound case.
*/
static inline void sky2_put_idx(struct sky2_hw *hw, unsigned q,
u16 idx, u16 *last, u16 size)
{
if (is_ec_a1(hw) && idx < *last) {
u16 hwget = sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_GET_IDX));
if (hwget == 0) {
/* Start prefetching again */
sky2_write8(hw, Y2_QADDR(q, PREF_UNIT_FIFO_WM), 0xe0);
goto setnew;
}
if (hwget == size - 1) {
/* set watermark to one list element */
sky2_write8(hw, Y2_QADDR(q, PREF_UNIT_FIFO_WM), 8);
/* set put index to first list element */
sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), 0);
} else /* have hardware go to end of list */
sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX),
size - 1);
} else {
setnew:
sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), idx);
}
*last = idx;
}
static inline struct sky2_rx_le *sky2_next_rx(struct sky2_port *sky2)
{
struct sky2_rx_le *le = sky2->rx_le + sky2->rx_put;
sky2->rx_put = (sky2->rx_put + 1) % RX_LE_SIZE;
return le;
}
/* Return high part of DMA address (could be 32 or 64 bit) */
static inline u32 high32(dma_addr_t a)
{
return (a >> 16) >> 16;
}
/* Build description to hardware about buffer */
static inline void sky2_rx_add(struct sky2_port *sky2, struct ring_info *re)
{
struct sky2_rx_le *le;
u32 hi = high32(re->mapaddr);
re->idx = sky2->rx_put;
if (sky2->rx_addr64 != hi) {
le = sky2_next_rx(sky2);
le->addr = cpu_to_le32(hi);
le->ctrl = 0;
le->opcode = OP_ADDR64 | HW_OWNER;
sky2->rx_addr64 = high32(re->mapaddr + re->maplen);
}
le = sky2_next_rx(sky2);
le->addr = cpu_to_le32((u32) re->mapaddr);
le->length = cpu_to_le16(re->maplen);
le->ctrl = 0;
le->opcode = OP_PACKET | HW_OWNER;
}
/* Tell chip where to start receive checksum.
* Actually has two checksums, but set both same to avoid possible byte
* order problems.
*/
static void rx_set_checksum(struct sky2_port *sky2)
{
struct sky2_rx_le *le;
le = sky2_next_rx(sky2);
le->addr = (ETH_HLEN << 16) | ETH_HLEN;
le->ctrl = 0;
le->opcode = OP_TCPSTART | HW_OWNER;
sky2_write32(sky2->hw,
Q_ADDR(rxqaddr[sky2->port], Q_CSR),
sky2->rx_csum ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM);
}
/*
* The RX Stop command will not work for Yukon-2 if the BMU does not
* reach the end of packet and since we can't make sure that we have
* incoming data, we must reset the BMU while it is not doing a DMA
* transfer. Since it is possible that the RX path is still active,
* the RX RAM buffer will be stopped first, so any possible incoming
* data will not trigger a DMA. After the RAM buffer is stopped, the
* BMU is polled until any DMA in progress is ended and only then it
* will be reset.
*/
static void sky2_rx_stop(struct sky2_port *sky2)
{
struct sky2_hw *hw = sky2->hw;
unsigned rxq = rxqaddr[sky2->port];
int i;
/* disable the RAM Buffer receive queue */
sky2_write8(hw, RB_ADDR(rxq, RB_CTRL), RB_DIS_OP_MD);
for (i = 0; i < 0xffff; i++)
if (sky2_read8(hw, RB_ADDR(rxq, Q_RSL))
== sky2_read8(hw, RB_ADDR(rxq, Q_RL)))
goto stopped;
printk(KERN_WARNING PFX "%s: receiver stop failed\n",
sky2->netdev->name);
stopped:
sky2_write32(hw, Q_ADDR(rxq, Q_CSR), BMU_RST_SET | BMU_FIFO_RST);
/* reset the Rx prefetch unit */
sky2_write32(hw, Y2_QADDR(rxq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET);
}
/* Clean out receive buffer area, assumes receiver hardware stopped */
static void sky2_rx_clean(struct sky2_port *sky2)
{
unsigned i;
memset(sky2->rx_le, 0, RX_LE_BYTES);
for (i = 0; i < sky2->rx_pending; i++) {
struct ring_info *re = sky2->rx_ring + i;
if (re->skb) {
pci_unmap_single(sky2->hw->pdev,
re->mapaddr, re->maplen,
PCI_DMA_FROMDEVICE);
kfree_skb(re->skb);
re->skb = NULL;
}
}
}
/* Basic MII support */
static int sky2_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
{
struct mii_ioctl_data *data = if_mii(ifr);
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
int err = -EOPNOTSUPP;
if (!netif_running(dev))
return -ENODEV; /* Phy still in reset */
switch(cmd) {
case SIOCGMIIPHY:
data->phy_id = PHY_ADDR_MARV;
/* fallthru */
case SIOCGMIIREG: {
u16 val = 0;
spin_lock_bh(&hw->phy_lock);
err = __gm_phy_read(hw, sky2->port, data->reg_num & 0x1f, &val);
spin_unlock_bh(&hw->phy_lock);
data->val_out = val;
break;
}
case SIOCSMIIREG:
if (!capable(CAP_NET_ADMIN))
return -EPERM;
spin_lock_bh(&hw->phy_lock);
err = gm_phy_write(hw, sky2->port, data->reg_num & 0x1f,
data->val_in);
spin_unlock_bh(&hw->phy_lock);
break;
}
return err;
}
#ifdef SKY2_VLAN_TAG_USED
static void sky2_vlan_rx_register(struct net_device *dev, struct vlan_group *grp)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
u16 port = sky2->port;
unsigned long flags;
spin_lock_irqsave(&sky2->tx_lock, flags);
sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), RX_VLAN_STRIP_ON);
sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_VLAN_TAG_ON);
sky2->vlgrp = grp;
spin_unlock_irqrestore(&sky2->tx_lock, flags);
}
static void sky2_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
u16 port = sky2->port;
unsigned long flags;
spin_lock_irqsave(&sky2->tx_lock, flags);
sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), RX_VLAN_STRIP_OFF);
sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_VLAN_TAG_OFF);
if (sky2->vlgrp)
sky2->vlgrp->vlan_devices[vid] = NULL;
spin_unlock_irqrestore(&sky2->tx_lock, flags);
}
#endif
#define roundup(x, y) ((((x)+((y)-1))/(y))*(y))
static inline unsigned rx_size(const struct sky2_port *sky2)
{
return roundup(sky2->netdev->mtu + ETH_HLEN + 4, 8);
}
/*
* Allocate and setup receiver buffer pool.
* In case of 64 bit dma, there are 2X as many list elements
* available as ring entries
* and need to reserve one list element so we don't wrap around.
*
* It appears the hardware has a bug in the FIFO logic that
* cause it to hang if the FIFO gets overrun and the receive buffer
* is not aligned. This means we can't use skb_reserve to align
* the IP header.
*/
static int sky2_rx_start(struct sky2_port *sky2)
{
struct sky2_hw *hw = sky2->hw;
unsigned size = rx_size(sky2);
unsigned rxq = rxqaddr[sky2->port];
int i;
sky2->rx_put = sky2->rx_next = 0;
sky2_qset(hw, rxq, is_pciex(hw) ? 0x80 : 0x600);
sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
rx_set_checksum(sky2);
for (i = 0; i < sky2->rx_pending; i++) {
struct ring_info *re = sky2->rx_ring + i;
re->skb = dev_alloc_skb(size);
if (!re->skb)
goto nomem;
re->mapaddr = pci_map_single(hw->pdev, re->skb->data,
size, PCI_DMA_FROMDEVICE);
re->maplen = size;
sky2_rx_add(sky2, re);
}
/* Tell chip about available buffers */
sky2_write16(hw, Y2_QADDR(rxq, PREF_UNIT_PUT_IDX), sky2->rx_put);
sky2->rx_last_put = sky2_read16(hw, Y2_QADDR(rxq, PREF_UNIT_PUT_IDX));
return 0;
nomem:
sky2_rx_clean(sky2);
return -ENOMEM;
}
/* Bring up network interface. */
static int sky2_up(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u32 ramsize, rxspace;
int err = -ENOMEM;
if (netif_msg_ifup(sky2))
printk(KERN_INFO PFX "%s: enabling interface\n", dev->name);
/* must be power of 2 */
sky2->tx_le = pci_alloc_consistent(hw->pdev,
TX_RING_SIZE *
sizeof(struct sky2_tx_le),
&sky2->tx_le_map);
if (!sky2->tx_le)
goto err_out;
sky2->tx_ring = kzalloc(TX_RING_SIZE * sizeof(struct ring_info),
GFP_KERNEL);
if (!sky2->tx_ring)
goto err_out;
sky2->tx_prod = sky2->tx_cons = 0;
sky2->rx_le = pci_alloc_consistent(hw->pdev, RX_LE_BYTES,
&sky2->rx_le_map);
if (!sky2->rx_le)
goto err_out;
memset(sky2->rx_le, 0, RX_LE_BYTES);
sky2->rx_ring = kzalloc(sky2->rx_pending * sizeof(struct ring_info),
GFP_KERNEL);
if (!sky2->rx_ring)
goto err_out;
sky2_mac_init(hw, port);
/* Configure RAM buffers */
if (hw->chip_id == CHIP_ID_YUKON_FE ||
(hw->chip_id == CHIP_ID_YUKON_EC && hw->chip_rev == 2))
ramsize = 4096;
else {
u8 e0 = sky2_read8(hw, B2_E_0);
ramsize = (e0 == 0) ? (128 * 1024) : (e0 * 4096);
}
/* 2/3 for Rx */
rxspace = (2 * ramsize) / 3;
sky2_ramset(hw, rxqaddr[port], 0, rxspace);
sky2_ramset(hw, txqaddr[port], rxspace, ramsize - rxspace);
/* Make sure SyncQ is disabled */
sky2_write8(hw, RB_ADDR(port == 0 ? Q_XS1 : Q_XS2, RB_CTRL),
RB_RST_SET);
sky2_qset(hw, txqaddr[port], 0x600);
if (hw->chip_id == CHIP_ID_YUKON_EC_U)
sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), 0x1a0);
sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
TX_RING_SIZE - 1);
err = sky2_rx_start(sky2);
if (err)
goto err_out;
/* Enable interrupts from phy/mac for port */
hw->intr_mask |= (port == 0) ? Y2_IS_PORT_1 : Y2_IS_PORT_2;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
return 0;
err_out:
if (sky2->rx_le)
pci_free_consistent(hw->pdev, RX_LE_BYTES,
sky2->rx_le, sky2->rx_le_map);
if (sky2->tx_le)
pci_free_consistent(hw->pdev,
TX_RING_SIZE * sizeof(struct sky2_tx_le),
sky2->tx_le, sky2->tx_le_map);
if (sky2->tx_ring)
kfree(sky2->tx_ring);
if (sky2->rx_ring)
kfree(sky2->rx_ring);
return err;
}
/* Modular subtraction in ring */
static inline int tx_dist(unsigned tail, unsigned head)
{
return (head >= tail ? head : head + TX_RING_SIZE) - tail;
}
/* Number of list elements available for next tx */
static inline int tx_avail(const struct sky2_port *sky2)
{
return sky2->tx_pending - tx_dist(sky2->tx_cons, sky2->tx_prod);
}
/* Estimate of number of transmit list elements required */
static inline unsigned tx_le_req(const struct sk_buff *skb)
{
unsigned count;
count = sizeof(dma_addr_t) / sizeof(u32);
count += skb_shinfo(skb)->nr_frags * count;
if (skb_shinfo(skb)->tso_size)
++count;
if (skb->ip_summed)
++count;
return count;
}
/*
* Put one packet in ring for transmit.
* A single packet can generate multiple list elements, and
* the number of ring elements will probably be less than the number
* of list elements used.
*/
static int sky2_xmit_frame(struct sk_buff *skb, struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
struct sky2_tx_le *le = NULL;
struct ring_info *re;
unsigned long flags;
unsigned i, len;
dma_addr_t mapping;
u32 addr64;
u16 mss;
u8 ctrl;
local_irq_save(flags);
if (!spin_trylock(&sky2->tx_lock)) {
local_irq_restore(flags);
return NETDEV_TX_LOCKED;
}
if (unlikely(tx_avail(sky2) < tx_le_req(skb))) {
netif_stop_queue(dev);
spin_unlock_irqrestore(&sky2->tx_lock, flags);
printk(KERN_WARNING PFX "%s: ring full when queue awake!\n",
dev->name);
return NETDEV_TX_BUSY;
}
if (unlikely(netif_msg_tx_queued(sky2)))
printk(KERN_DEBUG "%s: tx queued, slot %u, len %d\n",
dev->name, sky2->tx_prod, skb->len);
len = skb_headlen(skb);
mapping = pci_map_single(hw->pdev, skb->data, len, PCI_DMA_TODEVICE);
addr64 = high32(mapping);
re = sky2->tx_ring + sky2->tx_prod;
/* Send high bits if changed or crosses boundary */
if (addr64 != sky2->tx_addr64 || high32(mapping + len) != sky2->tx_addr64) {
le = get_tx_le(sky2);
le->tx.addr = cpu_to_le32(addr64);
le->ctrl = 0;
le->opcode = OP_ADDR64 | HW_OWNER;
sky2->tx_addr64 = high32(mapping + len);
}
/* Check for TCP Segmentation Offload */
mss = skb_shinfo(skb)->tso_size;
if (mss != 0) {
/* just drop the packet if non-linear expansion fails */
if (skb_header_cloned(skb) &&
pskb_expand_head(skb, 0, 0, GFP_ATOMIC)) {
dev_kfree_skb_any(skb);
goto out_unlock;
}
mss += ((skb->h.th->doff - 5) * 4); /* TCP options */
mss += (skb->nh.iph->ihl * 4) + sizeof(struct tcphdr);
mss += ETH_HLEN;
}
if (mss != sky2->tx_last_mss) {
le = get_tx_le(sky2);
le->tx.tso.size = cpu_to_le16(mss);
le->tx.tso.rsvd = 0;
le->opcode = OP_LRGLEN | HW_OWNER;
le->ctrl = 0;
sky2->tx_last_mss = mss;
}
ctrl = 0;
#ifdef SKY2_VLAN_TAG_USED
/* Add VLAN tag, can piggyback on LRGLEN or ADDR64 */
if (sky2->vlgrp && vlan_tx_tag_present(skb)) {
if (!le) {
le = get_tx_le(sky2);
le->tx.addr = 0;
le->opcode = OP_VLAN|HW_OWNER;
le->ctrl = 0;
} else
le->opcode |= OP_VLAN;
le->length = cpu_to_be16(vlan_tx_tag_get(skb));
ctrl |= INS_VLAN;
}
#endif
/* Handle TCP checksum offload */
if (skb->ip_summed == CHECKSUM_HW) {
u16 hdr = skb->h.raw - skb->data;
u16 offset = hdr + skb->csum;
ctrl = CALSUM | WR_SUM | INIT_SUM | LOCK_SUM;
if (skb->nh.iph->protocol == IPPROTO_UDP)
ctrl |= UDPTCP;
le = get_tx_le(sky2);
le->tx.csum.start = cpu_to_le16(hdr);
le->tx.csum.offset = cpu_to_le16(offset);
le->length = 0; /* initial checksum value */
le->ctrl = 1; /* one packet */
le->opcode = OP_TCPLISW | HW_OWNER;
}
le = get_tx_le(sky2);
le->tx.addr = cpu_to_le32((u32) mapping);
le->length = cpu_to_le16(len);
le->ctrl = ctrl;
le->opcode = mss ? (OP_LARGESEND | HW_OWNER) : (OP_PACKET | HW_OWNER);
/* Record the transmit mapping info */
re->skb = skb;
re->mapaddr = mapping;
re->maplen = len;
for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
struct ring_info *fre;
mapping = pci_map_page(hw->pdev, frag->page, frag->page_offset,
frag->size, PCI_DMA_TODEVICE);
addr64 = (mapping >> 16) >> 16;
if (addr64 != sky2->tx_addr64) {
le = get_tx_le(sky2);
le->tx.addr = cpu_to_le32(addr64);
le->ctrl = 0;
le->opcode = OP_ADDR64 | HW_OWNER;
sky2->tx_addr64 = addr64;
}
le = get_tx_le(sky2);
le->tx.addr = cpu_to_le32((u32) mapping);
le->length = cpu_to_le16(frag->size);
le->ctrl = ctrl;
le->opcode = OP_BUFFER | HW_OWNER;
fre = sky2->tx_ring
+ ((re - sky2->tx_ring) + i + 1) % TX_RING_SIZE;
fre->skb = NULL;
fre->mapaddr = mapping;
fre->maplen = frag->size;
}
re->idx = sky2->tx_prod;
le->ctrl |= EOP;
sky2_put_idx(hw, txqaddr[sky2->port], sky2->tx_prod,
&sky2->tx_last_put, TX_RING_SIZE);
if (tx_avail(sky2) < MAX_SKB_TX_LE + 1)
netif_stop_queue(dev);
out_unlock:
mmiowb();
spin_unlock_irqrestore(&sky2->tx_lock, flags);
dev->trans_start = jiffies;
return NETDEV_TX_OK;
}
/*
* Free ring elements from starting at tx_cons until "done"
*
* NB: the hardware will tell us about partial completion of multi-part
* buffers; these are deferred until completion.
*/
static void sky2_tx_complete(struct sky2_port *sky2, u16 done)
{
struct net_device *dev = sky2->netdev;
unsigned i;
if (done == sky2->tx_cons)
return;
if (unlikely(netif_msg_tx_done(sky2)))
printk(KERN_DEBUG "%s: tx done, up to %u\n",
dev->name, done);
spin_lock(&sky2->tx_lock);
while (sky2->tx_cons != done) {
struct ring_info *re = sky2->tx_ring + sky2->tx_cons;
struct sk_buff *skb;
/* Check for partial status */
if (tx_dist(sky2->tx_cons, done)
< tx_dist(sky2->tx_cons, re->idx))
goto out;
skb = re->skb;
pci_unmap_single(sky2->hw->pdev,
re->mapaddr, re->maplen, PCI_DMA_TODEVICE);
for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
struct ring_info *fre;
fre =
sky2->tx_ring + (sky2->tx_cons + i +
1) % TX_RING_SIZE;
pci_unmap_page(sky2->hw->pdev, fre->mapaddr,
fre->maplen, PCI_DMA_TODEVICE);
}
dev_kfree_skb_any(skb);
sky2->tx_cons = re->idx;
}
out:
if (netif_queue_stopped(dev) && tx_avail(sky2) > MAX_SKB_TX_LE)
netif_wake_queue(dev);
spin_unlock(&sky2->tx_lock);
}
/* Cleanup all untransmitted buffers, assume transmitter not running */
static inline void sky2_tx_clean(struct sky2_port *sky2)
{
sky2_tx_complete(sky2, sky2->tx_prod);
}
/* Network shutdown */
static int sky2_down(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u16 ctrl;
if (netif_msg_ifdown(sky2))
printk(KERN_INFO PFX "%s: disabling interface\n", dev->name);
/* Stop more packets from being queued */
netif_stop_queue(dev);
/* Disable port IRQ */
local_irq_disable();
hw->intr_mask &= ~((sky2->port == 0) ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2);
sky2_write32(hw, B0_IMSK, hw->intr_mask);
local_irq_enable();
sky2_phy_reset(hw, port);
/* Stop transmitter */
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_STOP);
sky2_read32(hw, Q_ADDR(txqaddr[port], Q_CSR));
sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL),
RB_RST_SET | RB_DIS_OP_MD);
ctrl = gma_read16(hw, port, GM_GP_CTRL);
ctrl &= ~(GM_GPCR_TX_ENA | GM_GPCR_RX_ENA);
gma_write16(hw, port, GM_GP_CTRL, ctrl);
sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
/* Workaround shared GMAC reset */
if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0
&& port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
/* Disable Force Sync bit and Enable Alloc bit */
sky2_write8(hw, SK_REG(port, TXA_CTRL),
TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC);
/* Stop Interval Timer and Limit Counter of Tx Arbiter */
sky2_write32(hw, SK_REG(port, TXA_ITI_INI), 0L);
sky2_write32(hw, SK_REG(port, TXA_LIM_INI), 0L);
/* Reset the PCI FIFO of the async Tx queue */
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR),
BMU_RST_SET | BMU_FIFO_RST);
/* Reset the Tx prefetch units */
sky2_write32(hw, Y2_QADDR(txqaddr[port], PREF_UNIT_CTRL),
PREF_UNIT_RST_SET);
sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET);
sky2_rx_stop(sky2);
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET);
/* turn off LED's */
sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
synchronize_irq(hw->pdev->irq);
sky2_tx_clean(sky2);
sky2_rx_clean(sky2);
pci_free_consistent(hw->pdev, RX_LE_BYTES,
sky2->rx_le, sky2->rx_le_map);
kfree(sky2->rx_ring);
pci_free_consistent(hw->pdev,
TX_RING_SIZE * sizeof(struct sky2_tx_le),
sky2->tx_le, sky2->tx_le_map);
kfree(sky2->tx_ring);
return 0;
}
static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux)
{
if (!hw->copper)
return SPEED_1000;
if (hw->chip_id == CHIP_ID_YUKON_FE)
return (aux & PHY_M_PS_SPEED_100) ? SPEED_100 : SPEED_10;
switch (aux & PHY_M_PS_SPEED_MSK) {
case PHY_M_PS_SPEED_1000:
return SPEED_1000;
case PHY_M_PS_SPEED_100:
return SPEED_100;
default:
return SPEED_10;
}
}
static void sky2_link_up(struct sky2_port *sky2)
{
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u16 reg;
/* Enable Transmit FIFO Underrun */
sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK);
reg = gma_read16(hw, port, GM_GP_CTRL);
if (sky2->duplex == DUPLEX_FULL || sky2->autoneg == AUTONEG_ENABLE)
reg |= GM_GPCR_DUP_FULL;
/* enable Rx/Tx */
reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA;
gma_write16(hw, port, GM_GP_CTRL, reg);
gma_read16(hw, port, GM_GP_CTRL);
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
netif_carrier_on(sky2->netdev);
netif_wake_queue(sky2->netdev);
/* Turn on link LED */
sky2_write8(hw, SK_REG(port, LNK_LED_REG),
LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF);
if (hw->chip_id == CHIP_ID_YUKON_XL) {
u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
PHY_M_LEDC_INIT_CTRL(sky2->speed ==
SPEED_10 ? 7 : 0) |
PHY_M_LEDC_STA1_CTRL(sky2->speed ==
SPEED_100 ? 7 : 0) |
PHY_M_LEDC_STA0_CTRL(sky2->speed ==
SPEED_1000 ? 7 : 0));
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
}
if (netif_msg_link(sky2))
printk(KERN_INFO PFX
"%s: Link is up at %d Mbps, %s duplex, flow control %s\n",
sky2->netdev->name, sky2->speed,
sky2->duplex == DUPLEX_FULL ? "full" : "half",
(sky2->tx_pause && sky2->rx_pause) ? "both" :
sky2->tx_pause ? "tx" : sky2->rx_pause ? "rx" : "none");
}
static void sky2_link_down(struct sky2_port *sky2)
{
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u16 reg;
gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);
reg = gma_read16(hw, port, GM_GP_CTRL);
reg &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA);
gma_write16(hw, port, GM_GP_CTRL, reg);
gma_read16(hw, port, GM_GP_CTRL); /* PCI post */
if (sky2->rx_pause && !sky2->tx_pause) {
/* restore Asymmetric Pause bit */
gm_phy_write(hw, port, PHY_MARV_AUNE_ADV,
gm_phy_read(hw, port, PHY_MARV_AUNE_ADV)
| PHY_M_AN_ASP);
}
sky2_phy_reset(hw, port);
netif_carrier_off(sky2->netdev);
netif_stop_queue(sky2->netdev);
/* Turn on link LED */
sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF);
if (netif_msg_link(sky2))
printk(KERN_INFO PFX "%s: Link is down.\n", sky2->netdev->name);
sky2_phy_init(hw, port);
}
static int sky2_autoneg_done(struct sky2_port *sky2, u16 aux)
{
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u16 lpa;
lpa = gm_phy_read(hw, port, PHY_MARV_AUNE_LP);
if (lpa & PHY_M_AN_RF) {
printk(KERN_ERR PFX "%s: remote fault", sky2->netdev->name);
return -1;
}
if (hw->chip_id != CHIP_ID_YUKON_FE &&
gm_phy_read(hw, port, PHY_MARV_1000T_STAT) & PHY_B_1000S_MSF) {
printk(KERN_ERR PFX "%s: master/slave fault",
sky2->netdev->name);
return -1;
}
if (!(aux & PHY_M_PS_SPDUP_RES)) {
printk(KERN_ERR PFX "%s: speed/duplex mismatch",
sky2->netdev->name);
return -1;
}
sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
sky2->speed = sky2_phy_speed(hw, aux);
/* Pause bits are offset (9..8) */
if (hw->chip_id == CHIP_ID_YUKON_XL)
aux >>= 6;
sky2->rx_pause = (aux & PHY_M_PS_RX_P_EN) != 0;
sky2->tx_pause = (aux & PHY_M_PS_TX_P_EN) != 0;
if ((sky2->tx_pause || sky2->rx_pause)
&& !(sky2->speed < SPEED_1000 && sky2->duplex == DUPLEX_HALF))
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
else
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
return 0;
}
/*
* Interrupt from PHY are handled in tasklet (soft irq)
* because accessing phy registers requires spin wait which might
* cause excess interrupt latency.
*/
static void sky2_phy_task(unsigned long data)
{
struct sky2_port *sky2 = (struct sky2_port *)data;
struct sky2_hw *hw = sky2->hw;
u16 istatus, phystat;
spin_lock(&hw->phy_lock);
istatus = gm_phy_read(hw, sky2->port, PHY_MARV_INT_STAT);
phystat = gm_phy_read(hw, sky2->port, PHY_MARV_PHY_STAT);
if (netif_msg_intr(sky2))
printk(KERN_INFO PFX "%s: phy interrupt status 0x%x 0x%x\n",
sky2->netdev->name, istatus, phystat);
if (istatus & PHY_M_IS_AN_COMPL) {
if (sky2_autoneg_done(sky2, phystat) == 0)
sky2_link_up(sky2);
goto out;
}
if (istatus & PHY_M_IS_LSP_CHANGE)
sky2->speed = sky2_phy_speed(hw, phystat);
if (istatus & PHY_M_IS_DUP_CHANGE)
sky2->duplex =
(phystat & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
if (istatus & PHY_M_IS_LST_CHANGE) {
if (phystat & PHY_M_PS_LINK_UP)
sky2_link_up(sky2);
else
sky2_link_down(sky2);
}
out:
spin_unlock(&hw->phy_lock);
local_irq_disable();
hw->intr_mask |= (sky2->port == 0) ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
local_irq_enable();
}
static void sky2_tx_timeout(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
if (netif_msg_timer(sky2))
printk(KERN_ERR PFX "%s: tx timeout\n", dev->name);
sky2_write32(sky2->hw, Q_ADDR(txqaddr[sky2->port], Q_CSR), BMU_STOP);
sky2_read32(sky2->hw, Q_ADDR(txqaddr[sky2->port], Q_CSR));
sky2_tx_clean(sky2);
}
static int sky2_change_mtu(struct net_device *dev, int new_mtu)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
int err;
u16 ctl, mode;
if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU)
return -EINVAL;
if (hw->chip_id == CHIP_ID_YUKON_EC_U && new_mtu > ETH_DATA_LEN)
return -EINVAL;
if (!netif_running(dev)) {
dev->mtu = new_mtu;
return 0;
}
sky2_write32(hw, B0_IMSK, 0);
dev->trans_start = jiffies; /* prevent tx timeout */
netif_stop_queue(dev);
netif_poll_disable(hw->dev[0]);
ctl = gma_read16(hw, sky2->port, GM_GP_CTRL);
gma_write16(hw, sky2->port, GM_GP_CTRL, ctl & ~GM_GPCR_RX_ENA);
sky2_rx_stop(sky2);
sky2_rx_clean(sky2);
dev->mtu = new_mtu;
mode = DATA_BLIND_VAL(DATA_BLIND_DEF) |
GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF);
if (dev->mtu > ETH_DATA_LEN)
mode |= GM_SMOD_JUMBO_ENA;
gma_write16(hw, sky2->port, GM_SERIAL_MODE, mode);
sky2_write8(hw, RB_ADDR(rxqaddr[sky2->port], RB_CTRL), RB_ENA_OP_MD);
err = sky2_rx_start(sky2);
gma_write16(hw, sky2->port, GM_GP_CTRL, ctl);
netif_poll_disable(hw->dev[0]);
netif_wake_queue(dev);
sky2_write32(hw, B0_IMSK, hw->intr_mask);
return err;
}
/*
* Receive one packet.
* For small packets or errors, just reuse existing skb.
* For larger packets, get new buffer.
*/
static struct sk_buff *sky2_receive(struct sky2_port *sky2,
u16 length, u32 status)
{
struct ring_info *re = sky2->rx_ring + sky2->rx_next;
struct sk_buff *skb = NULL;
const unsigned int bufsize = rx_size(sky2);
if (unlikely(netif_msg_rx_status(sky2)))
printk(KERN_DEBUG PFX "%s: rx slot %u status 0x%x len %d\n",
sky2->netdev->name, sky2->rx_next, status, length);
sky2->rx_next = (sky2->rx_next + 1) % sky2->rx_pending;
if (status & GMR_FS_ANY_ERR)
goto error;
if (!(status & GMR_FS_RX_OK))
goto resubmit;
if (length < RX_COPY_THRESHOLD) {
skb = alloc_skb(length + 2, GFP_ATOMIC);
if (!skb)
goto resubmit;
skb_reserve(skb, 2);
pci_dma_sync_single_for_cpu(sky2->hw->pdev, re->mapaddr,
length, PCI_DMA_FROMDEVICE);
memcpy(skb->data, re->skb->data, length);
skb->ip_summed = re->skb->ip_summed;
skb->csum = re->skb->csum;
pci_dma_sync_single_for_device(sky2->hw->pdev, re->mapaddr,
length, PCI_DMA_FROMDEVICE);
} else {
struct sk_buff *nskb;
nskb = dev_alloc_skb(bufsize);
if (!nskb)
goto resubmit;
skb = re->skb;
re->skb = nskb;
pci_unmap_single(sky2->hw->pdev, re->mapaddr,
re->maplen, PCI_DMA_FROMDEVICE);
prefetch(skb->data);
re->mapaddr = pci_map_single(sky2->hw->pdev, nskb->data,
bufsize, PCI_DMA_FROMDEVICE);
re->maplen = bufsize;
}
skb_put(skb, length);
resubmit:
re->skb->ip_summed = CHECKSUM_NONE;
sky2_rx_add(sky2, re);
/* Tell receiver about new buffers. */
sky2_put_idx(sky2->hw, rxqaddr[sky2->port], sky2->rx_put,
&sky2->rx_last_put, RX_LE_SIZE);
return skb;
error:
if (netif_msg_rx_err(sky2))
printk(KERN_INFO PFX "%s: rx error, status 0x%x length %d\n",
sky2->netdev->name, status, length);
if (status & (GMR_FS_LONG_ERR | GMR_FS_UN_SIZE))
sky2->net_stats.rx_length_errors++;
if (status & GMR_FS_FRAGMENT)
sky2->net_stats.rx_frame_errors++;
if (status & GMR_FS_CRC_ERR)
sky2->net_stats.rx_crc_errors++;
if (status & GMR_FS_RX_FF_OV)
sky2->net_stats.rx_fifo_errors++;
goto resubmit;
}
/*
* Check for transmit complete
*/
static inline void sky2_tx_check(struct sky2_hw *hw, int port)
{
struct net_device *dev = hw->dev[port];
if (dev && netif_running(dev)) {
sky2_tx_complete(netdev_priv(dev),
sky2_read16(hw, port == 0
? STAT_TXA1_RIDX : STAT_TXA2_RIDX));
}
}
/*
* Both ports share the same status interrupt, therefore there is only
* one poll routine.
*/
static int sky2_poll(struct net_device *dev0, int *budget)
{
struct sky2_hw *hw = ((struct sky2_port *) netdev_priv(dev0))->hw;
unsigned int to_do = min(dev0->quota, *budget);
unsigned int work_done = 0;
u16 hwidx;
hwidx = sky2_read16(hw, STAT_PUT_IDX);
BUG_ON(hwidx >= STATUS_RING_SIZE);
rmb();
while (hwidx != hw->st_idx) {
struct sky2_status_le *le = hw->st_le + hw->st_idx;
struct net_device *dev;
struct sky2_port *sky2;
struct sk_buff *skb;
u32 status;
u16 length;
u8 op;
le = hw->st_le + hw->st_idx;
hw->st_idx = (hw->st_idx + 1) % STATUS_RING_SIZE;
prefetch(hw->st_le + hw->st_idx);
BUG_ON(le->link >= hw->ports || !hw->dev[le->link]);
BUG_ON(le->link >= 2);
dev = hw->dev[le->link];
if (dev == NULL || !netif_running(dev))
continue;
sky2 = netdev_priv(dev);
status = le32_to_cpu(le->status);
length = le16_to_cpu(le->length);
op = le->opcode & ~HW_OWNER;
le->opcode = 0;
switch (op) {
case OP_RXSTAT:
skb = sky2_receive(sky2, length, status);
if (!skb)
break;
skb->dev = dev;
skb->protocol = eth_type_trans(skb, dev);
dev->last_rx = jiffies;
#ifdef SKY2_VLAN_TAG_USED
if (sky2->vlgrp && (status & GMR_FS_VLAN)) {
vlan_hwaccel_receive_skb(skb,
sky2->vlgrp,
be16_to_cpu(sky2->rx_tag));
} else
#endif
netif_receive_skb(skb);
if (++work_done >= to_do)
goto exit_loop;
break;
#ifdef SKY2_VLAN_TAG_USED
case OP_RXVLAN:
sky2->rx_tag = length;
break;
case OP_RXCHKSVLAN:
sky2->rx_tag = length;
/* fall through */
#endif
case OP_RXCHKS:
skb = sky2->rx_ring[sky2->rx_next].skb;
skb->ip_summed = CHECKSUM_HW;
skb->csum = le16_to_cpu(status);
break;
case OP_TXINDEXLE:
/* pick up transmit status later */
break;
default:
if (net_ratelimit())
printk(KERN_WARNING PFX
"unknown status opcode 0x%x\n", op);
break;
}
}
exit_loop:
sky2_tx_check(hw, 0);
sky2_tx_check(hw, 1);
mmiowb();
if (work_done < to_do) {
/*
* Another chip workaround, need to restart TX timer if status
* LE was handled. WA_DEV_43_418
*/
if (is_ec_a1(hw)) {
sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP);
sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
}
netif_rx_complete(dev0);
hw->intr_mask |= Y2_IS_STAT_BMU;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
mmiowb();
return 0;
} else {
*budget -= work_done;
dev0->quota -= work_done;
return 1;
}
}
static void sky2_hw_error(struct sky2_hw *hw, unsigned port, u32 status)
{
struct net_device *dev = hw->dev[port];
printk(KERN_INFO PFX "%s: hw error interrupt status 0x%x\n",
dev->name, status);
if (status & Y2_IS_PAR_RD1) {
printk(KERN_ERR PFX "%s: ram data read parity error\n",
dev->name);
/* Clear IRQ */
sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_RD_PERR);
}
if (status & Y2_IS_PAR_WR1) {
printk(KERN_ERR PFX "%s: ram data write parity error\n",
dev->name);
sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_WR_PERR);
}
if (status & Y2_IS_PAR_MAC1) {
printk(KERN_ERR PFX "%s: MAC parity error\n", dev->name);
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_PE);
}
if (status & Y2_IS_PAR_RX1) {
printk(KERN_ERR PFX "%s: RX parity error\n", dev->name);
sky2_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), BMU_CLR_IRQ_PAR);
}
if (status & Y2_IS_TCP_TXA1) {
printk(KERN_ERR PFX "%s: TCP segmentation error\n", dev->name);
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_CLR_IRQ_TCP);
}
}
static void sky2_hw_intr(struct sky2_hw *hw)
{
u32 status = sky2_read32(hw, B0_HWE_ISRC);
if (status & Y2_IS_TIST_OV)
sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) {
u16 pci_err;
pci_read_config_word(hw->pdev, PCI_STATUS, &pci_err);
printk(KERN_ERR PFX "%s: pci hw error (0x%x)\n",
pci_name(hw->pdev), pci_err);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
pci_write_config_word(hw->pdev, PCI_STATUS,
pci_err | PCI_STATUS_ERROR_BITS);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
if (status & Y2_IS_PCI_EXP) {
/* PCI-Express uncorrectable Error occurred */
u32 pex_err;
pci_read_config_dword(hw->pdev, PEX_UNC_ERR_STAT, &pex_err);
printk(KERN_ERR PFX "%s: pci express error (0x%x)\n",
pci_name(hw->pdev), pex_err);
/* clear the interrupt */
sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT,
0xffffffffUL);
sky2_write32(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
if (pex_err & PEX_FATAL_ERRORS) {
u32 hwmsk = sky2_read32(hw, B0_HWE_IMSK);
hwmsk &= ~Y2_IS_PCI_EXP;
sky2_write32(hw, B0_HWE_IMSK, hwmsk);
}
}
if (status & Y2_HWE_L1_MASK)
sky2_hw_error(hw, 0, status);
status >>= 8;
if (status & Y2_HWE_L1_MASK)
sky2_hw_error(hw, 1, status);
}
static void sky2_mac_intr(struct sky2_hw *hw, unsigned port)
{
struct net_device *dev = hw->dev[port];
struct sky2_port *sky2 = netdev_priv(dev);
u8 status = sky2_read8(hw, SK_REG(port, GMAC_IRQ_SRC));
if (netif_msg_intr(sky2))
printk(KERN_INFO PFX "%s: mac interrupt status 0x%x\n",
dev->name, status);
if (status & GM_IS_RX_FF_OR) {
++sky2->net_stats.rx_fifo_errors;
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_CLI_RX_FO);
}
if (status & GM_IS_TX_FF_UR) {
++sky2->net_stats.tx_fifo_errors;
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_FU);
}
}
static void sky2_phy_intr(struct sky2_hw *hw, unsigned port)
{
struct net_device *dev = hw->dev[port];
struct sky2_port *sky2 = netdev_priv(dev);
hw->intr_mask &= ~(port == 0 ? Y2_IS_IRQ_PHY1 : Y2_IS_IRQ_PHY2);
sky2_write32(hw, B0_IMSK, hw->intr_mask);
tasklet_schedule(&sky2->phy_task);
}
static irqreturn_t sky2_intr(int irq, void *dev_id, struct pt_regs *regs)
{
struct sky2_hw *hw = dev_id;
struct net_device *dev0 = hw->dev[0];
u32 status;
status = sky2_read32(hw, B0_Y2_SP_ISRC2);
if (status == 0 || status == ~0)
return IRQ_NONE;
if (status & Y2_IS_HW_ERR)
sky2_hw_intr(hw);
/* Do NAPI for Rx and Tx status */
if (status & Y2_IS_STAT_BMU) {
hw->intr_mask &= ~Y2_IS_STAT_BMU;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
if (likely(__netif_rx_schedule_prep(dev0))) {
prefetch(&hw->st_le[hw->st_idx]);
__netif_rx_schedule(dev0);
}
}
if (status & Y2_IS_IRQ_PHY1)
sky2_phy_intr(hw, 0);
if (status & Y2_IS_IRQ_PHY2)
sky2_phy_intr(hw, 1);
if (status & Y2_IS_IRQ_MAC1)
sky2_mac_intr(hw, 0);
if (status & Y2_IS_IRQ_MAC2)
sky2_mac_intr(hw, 1);
sky2_write32(hw, B0_Y2_SP_ICR, 2);
sky2_read32(hw, B0_IMSK);
return IRQ_HANDLED;
}
#ifdef CONFIG_NET_POLL_CONTROLLER
static void sky2_netpoll(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
sky2_intr(sky2->hw->pdev->irq, sky2->hw, NULL);
}
#endif
/* Chip internal frequency for clock calculations */
static inline u32 sky2_khz(const struct sky2_hw *hw)
{
switch (hw->chip_id) {
case CHIP_ID_YUKON_EC:
case CHIP_ID_YUKON_EC_U:
return 125000; /* 125 Mhz */
case CHIP_ID_YUKON_FE:
return 100000; /* 100 Mhz */
default: /* YUKON_XL */
return 156000; /* 156 Mhz */
}
}
static inline u32 sky2_ms2clk(const struct sky2_hw *hw, u32 ms)
{
return sky2_khz(hw) * ms;
}
static inline u32 sky2_us2clk(const struct sky2_hw *hw, u32 us)
{
return (sky2_khz(hw) * us) / 1000;
}
static int sky2_reset(struct sky2_hw *hw)
{
u32 ctst;
u16 status;
u8 t8, pmd_type;
int i;
ctst = sky2_read32(hw, B0_CTST);
sky2_write8(hw, B0_CTST, CS_RST_CLR);
hw->chip_id = sky2_read8(hw, B2_CHIP_ID);
if (hw->chip_id < CHIP_ID_YUKON_XL || hw->chip_id > CHIP_ID_YUKON_FE) {
printk(KERN_ERR PFX "%s: unsupported chip type 0x%x\n",
pci_name(hw->pdev), hw->chip_id);
return -EOPNOTSUPP;
}
/* ring for status responses */
hw->st_le = pci_alloc_consistent(hw->pdev, STATUS_LE_BYTES,
&hw->st_dma);
if (!hw->st_le)
return -ENOMEM;
/* disable ASF */
if (hw->chip_id <= CHIP_ID_YUKON_EC) {
sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
sky2_write16(hw, B0_CTST, Y2_ASF_DISABLE);
}
/* do a SW reset */
sky2_write8(hw, B0_CTST, CS_RST_SET);
sky2_write8(hw, B0_CTST, CS_RST_CLR);
/* clear PCI errors, if any */
pci_read_config_word(hw->pdev, PCI_STATUS, &status);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
pci_write_config_word(hw->pdev, PCI_STATUS,
status | PCI_STATUS_ERROR_BITS);
sky2_write8(hw, B0_CTST, CS_MRST_CLR);
/* clear any PEX errors */
if (is_pciex(hw)) {
u16 lstat;
pci_write_config_dword(hw->pdev, PEX_UNC_ERR_STAT,
0xffffffffUL);
pci_read_config_word(hw->pdev, PEX_LNK_STAT, &lstat);
}
pmd_type = sky2_read8(hw, B2_PMD_TYP);
hw->copper = !(pmd_type == 'L' || pmd_type == 'S');
hw->ports = 1;
t8 = sky2_read8(hw, B2_Y2_HW_RES);
if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) {
if (!(sky2_read8(hw, B2_Y2_CLK_GATE) & Y2_STATUS_LNK2_INAC))
++hw->ports;
}
hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4;
sky2_set_power_state(hw, PCI_D0);
for (i = 0; i < hw->ports; i++) {
sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET);
sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR);
}
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
/* Clear I2C IRQ noise */
sky2_write32(hw, B2_I2C_IRQ, 1);
/* turn off hardware timer (unused) */
sky2_write8(hw, B2_TI_CTRL, TIM_STOP);
sky2_write8(hw, B2_TI_CTRL, TIM_CLR_IRQ);
sky2_write8(hw, B0_Y2LED, LED_STAT_ON);
/* Turn on descriptor polling (every 75us) */
sky2_write32(hw, B28_DPT_INI, sky2_us2clk(hw, 75));
sky2_write8(hw, B28_DPT_CTRL, DPT_START);
/* Turn off receive timestamp */
sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_STOP);
sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ);
/* enable the Tx Arbiters */
for (i = 0; i < hw->ports; i++)
sky2_write8(hw, SK_REG(i, TXA_CTRL), TXA_ENA_ARB);
/* Initialize ram interface */
for (i = 0; i < hw->ports; i++) {
sky2_write8(hw, RAM_BUFFER(i, B3_RI_CTRL), RI_RST_CLR);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R1), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA1), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS1), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R1), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA1), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS1), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R2), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA2), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS2), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R2), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA2), SK_RI_TO_53);
sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS2), SK_RI_TO_53);
}
if (is_pciex(hw)) {
u16 pctrl;
/* change Max. Read Request Size to 2048 bytes */
pci_read_config_word(hw->pdev, PEX_DEV_CTRL, &pctrl);
pctrl &= ~PEX_DC_MAX_RRS_MSK;
pctrl |= PEX_DC_MAX_RD_RQ_SIZE(4);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
pci_write_config_word(hw->pdev, PEX_DEV_CTRL, pctrl);
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
sky2_write32(hw, B0_HWE_IMSK, Y2_HWE_ALL_MASK);
spin_lock_bh(&hw->phy_lock);
for (i = 0; i < hw->ports; i++)
sky2_phy_reset(hw, i);
spin_unlock_bh(&hw->phy_lock);
memset(hw->st_le, 0, STATUS_LE_BYTES);
hw->st_idx = 0;
sky2_write32(hw, STAT_CTRL, SC_STAT_RST_SET);
sky2_write32(hw, STAT_CTRL, SC_STAT_RST_CLR);
sky2_write32(hw, STAT_LIST_ADDR_LO, hw->st_dma);
sky2_write32(hw, STAT_LIST_ADDR_HI, (u64) hw->st_dma >> 32);
/* Set the list last index */
sky2_write16(hw, STAT_LAST_IDX, STATUS_RING_SIZE - 1);
sky2_write32(hw, STAT_TX_TIMER_INI, sky2_ms2clk(hw, 10));
/* These status setup values are copied from SysKonnect's driver */
if (is_ec_a1(hw)) {
/* WA for dev. #4.3 */
sky2_write16(hw, STAT_TX_IDX_TH, 0xfff); /* Tx Threshold */
/* set Status-FIFO watermark */
sky2_write8(hw, STAT_FIFO_WM, 0x21); /* WA for dev. #4.18 */
/* set Status-FIFO ISR watermark */
sky2_write8(hw, STAT_FIFO_ISR_WM, 0x07); /* WA for dev. #4.18 */
} else {
sky2_write16(hw, STAT_TX_IDX_TH, 0x000a);
/* set Status-FIFO watermark */
sky2_write8(hw, STAT_FIFO_WM, 0x10);
/* set Status-FIFO ISR watermark */
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0)
sky2_write8(hw, STAT_FIFO_ISR_WM, 0x10);
else /* WA dev 4.109 */
sky2_write8(hw, STAT_FIFO_ISR_WM, 0x04);
sky2_write32(hw, STAT_ISR_TIMER_INI, 0x0190);
}
/* enable status unit */
sky2_write32(hw, STAT_CTRL, SC_STAT_OP_ON);
sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START);
sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START);
sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START);
return 0;
}
static inline u32 sky2_supported_modes(const struct sky2_hw *hw)
{
u32 modes;
if (hw->copper) {
modes = SUPPORTED_10baseT_Half
| SUPPORTED_10baseT_Full
| SUPPORTED_100baseT_Half
| SUPPORTED_100baseT_Full
| SUPPORTED_Autoneg | SUPPORTED_TP;
if (hw->chip_id != CHIP_ID_YUKON_FE)
modes |= SUPPORTED_1000baseT_Half
| SUPPORTED_1000baseT_Full;
} else
modes = SUPPORTED_1000baseT_Full | SUPPORTED_FIBRE
| SUPPORTED_Autoneg;
return modes;
}
static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
ecmd->transceiver = XCVR_INTERNAL;
ecmd->supported = sky2_supported_modes(hw);
ecmd->phy_address = PHY_ADDR_MARV;
if (hw->copper) {
ecmd->supported = SUPPORTED_10baseT_Half
| SUPPORTED_10baseT_Full
| SUPPORTED_100baseT_Half
| SUPPORTED_100baseT_Full
| SUPPORTED_1000baseT_Half
| SUPPORTED_1000baseT_Full
| SUPPORTED_Autoneg | SUPPORTED_TP;
ecmd->port = PORT_TP;
} else
ecmd->port = PORT_FIBRE;
ecmd->advertising = sky2->advertising;
ecmd->autoneg = sky2->autoneg;
ecmd->speed = sky2->speed;
ecmd->duplex = sky2->duplex;
return 0;
}
static int sky2_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
{
struct sky2_port *sky2 = netdev_priv(dev);
const struct sky2_hw *hw = sky2->hw;
u32 supported = sky2_supported_modes(hw);
if (ecmd->autoneg == AUTONEG_ENABLE) {
ecmd->advertising = supported;
sky2->duplex = -1;
sky2->speed = -1;
} else {
u32 setting;
switch (ecmd->speed) {
case SPEED_1000:
if (ecmd->duplex == DUPLEX_FULL)
setting = SUPPORTED_1000baseT_Full;
else if (ecmd->duplex == DUPLEX_HALF)
setting = SUPPORTED_1000baseT_Half;
else
return -EINVAL;
break;
case SPEED_100:
if (ecmd->duplex == DUPLEX_FULL)
setting = SUPPORTED_100baseT_Full;
else if (ecmd->duplex == DUPLEX_HALF)
setting = SUPPORTED_100baseT_Half;
else
return -EINVAL;
break;
case SPEED_10:
if (ecmd->duplex == DUPLEX_FULL)
setting = SUPPORTED_10baseT_Full;
else if (ecmd->duplex == DUPLEX_HALF)
setting = SUPPORTED_10baseT_Half;
else
return -EINVAL;
break;
default:
return -EINVAL;
}
if ((setting & supported) == 0)
return -EINVAL;
sky2->speed = ecmd->speed;
sky2->duplex = ecmd->duplex;
}
sky2->autoneg = ecmd->autoneg;
sky2->advertising = ecmd->advertising;
if (netif_running(dev)) {
sky2_down(dev);
sky2_up(dev);
}
return 0;
}
static void sky2_get_drvinfo(struct net_device *dev,
struct ethtool_drvinfo *info)
{
struct sky2_port *sky2 = netdev_priv(dev);
strcpy(info->driver, DRV_NAME);
strcpy(info->version, DRV_VERSION);
strcpy(info->fw_version, "N/A");
strcpy(info->bus_info, pci_name(sky2->hw->pdev));
}
static const struct sky2_stat {
char name[ETH_GSTRING_LEN];
u16 offset;
} sky2_stats[] = {
{ "tx_bytes", GM_TXO_OK_HI },
{ "rx_bytes", GM_RXO_OK_HI },
{ "tx_broadcast", GM_TXF_BC_OK },
{ "rx_broadcast", GM_RXF_BC_OK },
{ "tx_multicast", GM_TXF_MC_OK },
{ "rx_multicast", GM_RXF_MC_OK },
{ "tx_unicast", GM_TXF_UC_OK },
{ "rx_unicast", GM_RXF_UC_OK },
{ "tx_mac_pause", GM_TXF_MPAUSE },
{ "rx_mac_pause", GM_RXF_MPAUSE },
{ "collisions", GM_TXF_SNG_COL },
{ "late_collision",GM_TXF_LAT_COL },
{ "aborted", GM_TXF_ABO_COL },
{ "multi_collisions", GM_TXF_MUL_COL },
{ "fifo_underrun", GM_TXE_FIFO_UR },
{ "fifo_overflow", GM_RXE_FIFO_OV },
{ "rx_toolong", GM_RXF_LNG_ERR },
{ "rx_jabber", GM_RXF_JAB_PKT },
{ "rx_runt", GM_RXE_FRAG },
{ "rx_too_long", GM_RXF_LNG_ERR },
{ "rx_fcs_error", GM_RXF_FCS_ERR },
};
static u32 sky2_get_rx_csum(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
return sky2->rx_csum;
}
static int sky2_set_rx_csum(struct net_device *dev, u32 data)
{
struct sky2_port *sky2 = netdev_priv(dev);
sky2->rx_csum = data;
sky2_write32(sky2->hw, Q_ADDR(rxqaddr[sky2->port], Q_CSR),
data ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM);
return 0;
}
static u32 sky2_get_msglevel(struct net_device *netdev)
{
struct sky2_port *sky2 = netdev_priv(netdev);
return sky2->msg_enable;
}
static int sky2_nway_reset(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
if (sky2->autoneg != AUTONEG_ENABLE)
return -EINVAL;
netif_stop_queue(dev);
spin_lock_irq(&hw->phy_lock);
sky2_phy_reset(hw, sky2->port);
sky2_phy_init(hw, sky2->port);
spin_unlock_irq(&hw->phy_lock);
return 0;
}
static void sky2_phy_stats(struct sky2_port *sky2, u64 * data, unsigned count)
{
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
int i;
data[0] = (u64) gma_read32(hw, port, GM_TXO_OK_HI) << 32
| (u64) gma_read32(hw, port, GM_TXO_OK_LO);
data[1] = (u64) gma_read32(hw, port, GM_RXO_OK_HI) << 32
| (u64) gma_read32(hw, port, GM_RXO_OK_LO);
for (i = 2; i < count; i++)
data[i] = (u64) gma_read32(hw, port, sky2_stats[i].offset);
}
static void sky2_set_msglevel(struct net_device *netdev, u32 value)
{
struct sky2_port *sky2 = netdev_priv(netdev);
sky2->msg_enable = value;
}
static int sky2_get_stats_count(struct net_device *dev)
{
return ARRAY_SIZE(sky2_stats);
}
static void sky2_get_ethtool_stats(struct net_device *dev,
struct ethtool_stats *stats, u64 * data)
{
struct sky2_port *sky2 = netdev_priv(dev);
sky2_phy_stats(sky2, data, ARRAY_SIZE(sky2_stats));
}
static void sky2_get_strings(struct net_device *dev, u32 stringset, u8 * data)
{
int i;
switch (stringset) {
case ETH_SS_STATS:
for (i = 0; i < ARRAY_SIZE(sky2_stats); i++)
memcpy(data + i * ETH_GSTRING_LEN,
sky2_stats[i].name, ETH_GSTRING_LEN);
break;
}
}
/* Use hardware MIB variables for critical path statistics and
* transmit feedback not reported at interrupt.
* Other errors are accounted for in interrupt handler.
*/
static struct net_device_stats *sky2_get_stats(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
u64 data[13];
sky2_phy_stats(sky2, data, ARRAY_SIZE(data));
sky2->net_stats.tx_bytes = data[0];
sky2->net_stats.rx_bytes = data[1];
sky2->net_stats.tx_packets = data[2] + data[4] + data[6];
sky2->net_stats.rx_packets = data[3] + data[5] + data[7];
sky2->net_stats.multicast = data[5] + data[7];
sky2->net_stats.collisions = data[10];
sky2->net_stats.tx_aborted_errors = data[12];
return &sky2->net_stats;
}
static int sky2_set_mac_address(struct net_device *dev, void *p)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sockaddr *addr = p;
int err = 0;
if (!is_valid_ether_addr(addr->sa_data))
return -EADDRNOTAVAIL;
sky2_down(dev);
memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
memcpy_toio(sky2->hw->regs + B2_MAC_1 + sky2->port * 8,
dev->dev_addr, ETH_ALEN);
memcpy_toio(sky2->hw->regs + B2_MAC_2 + sky2->port * 8,
dev->dev_addr, ETH_ALEN);
if (dev->flags & IFF_UP)
err = sky2_up(dev);
return err;
}
static void sky2_set_multicast(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
struct dev_mc_list *list = dev->mc_list;
u16 reg;
u8 filter[8];
memset(filter, 0, sizeof(filter));
reg = gma_read16(hw, port, GM_RX_CTRL);
reg |= GM_RXCR_UCF_ENA;
if (dev->flags & IFF_PROMISC) /* promiscuous */
reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
else if ((dev->flags & IFF_ALLMULTI) || dev->mc_count > 16) /* all multicast */
memset(filter, 0xff, sizeof(filter));
else if (dev->mc_count == 0) /* no multicast */
reg &= ~GM_RXCR_MCF_ENA;
else {
int i;
reg |= GM_RXCR_MCF_ENA;
for (i = 0; list && i < dev->mc_count; i++, list = list->next) {
u32 bit = ether_crc(ETH_ALEN, list->dmi_addr) & 0x3f;
filter[bit / 8] |= 1 << (bit % 8);
}
}
gma_write16(hw, port, GM_MC_ADDR_H1,
(u16) filter[0] | ((u16) filter[1] << 8));
gma_write16(hw, port, GM_MC_ADDR_H2,
(u16) filter[2] | ((u16) filter[3] << 8));
gma_write16(hw, port, GM_MC_ADDR_H3,
(u16) filter[4] | ((u16) filter[5] << 8));
gma_write16(hw, port, GM_MC_ADDR_H4,
(u16) filter[6] | ((u16) filter[7] << 8));
gma_write16(hw, port, GM_RX_CTRL, reg);
}
/* Can have one global because blinking is controlled by
* ethtool and that is always under RTNL mutex
*/
static inline void sky2_led(struct sky2_hw *hw, unsigned port, int on)
{
u16 pg;
spin_lock_bh(&hw->phy_lock);
switch (hw->chip_id) {
case CHIP_ID_YUKON_XL:
pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
on ? (PHY_M_LEDC_LOS_CTRL(1) |
PHY_M_LEDC_INIT_CTRL(7) |
PHY_M_LEDC_STA1_CTRL(7) |
PHY_M_LEDC_STA0_CTRL(7))
: 0);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
break;
default:
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0);
gm_phy_write(hw, port, PHY_MARV_LED_OVER,
on ? PHY_M_LED_MO_DUP(MO_LED_ON) |
PHY_M_LED_MO_10(MO_LED_ON) |
PHY_M_LED_MO_100(MO_LED_ON) |
PHY_M_LED_MO_1000(MO_LED_ON) |
PHY_M_LED_MO_RX(MO_LED_ON)
: PHY_M_LED_MO_DUP(MO_LED_OFF) |
PHY_M_LED_MO_10(MO_LED_OFF) |
PHY_M_LED_MO_100(MO_LED_OFF) |
PHY_M_LED_MO_1000(MO_LED_OFF) |
PHY_M_LED_MO_RX(MO_LED_OFF));
}
spin_unlock_bh(&hw->phy_lock);
}
/* blink LED's for finding board */
static int sky2_phys_id(struct net_device *dev, u32 data)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
unsigned port = sky2->port;
u16 ledctrl, ledover = 0;
long ms;
int onoff = 1;
if (!data || data > (u32) (MAX_SCHEDULE_TIMEOUT / HZ))
ms = jiffies_to_msecs(MAX_SCHEDULE_TIMEOUT);
else
ms = data * 1000;
/* save initial values */
spin_lock_bh(&hw->phy_lock);
if (hw->chip_id == CHIP_ID_YUKON_XL) {
u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
ledctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
} else {
ledctrl = gm_phy_read(hw, port, PHY_MARV_LED_CTRL);
ledover = gm_phy_read(hw, port, PHY_MARV_LED_OVER);
}
spin_unlock_bh(&hw->phy_lock);
while (ms > 0) {
sky2_led(hw, port, onoff);
onoff = !onoff;
if (msleep_interruptible(250))
break; /* interrupted */
ms -= 250;
}
/* resume regularly scheduled programming */
spin_lock_bh(&hw->phy_lock);
if (hw->chip_id == CHIP_ID_YUKON_XL) {
u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ledctrl);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
} else {
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover);
}
spin_unlock_bh(&hw->phy_lock);
return 0;
}
static void sky2_get_pauseparam(struct net_device *dev,
struct ethtool_pauseparam *ecmd)
{
struct sky2_port *sky2 = netdev_priv(dev);
ecmd->tx_pause = sky2->tx_pause;
ecmd->rx_pause = sky2->rx_pause;
ecmd->autoneg = sky2->autoneg;
}
static int sky2_set_pauseparam(struct net_device *dev,
struct ethtool_pauseparam *ecmd)
{
struct sky2_port *sky2 = netdev_priv(dev);
int err = 0;
sky2->autoneg = ecmd->autoneg;
sky2->tx_pause = ecmd->tx_pause != 0;
sky2->rx_pause = ecmd->rx_pause != 0;
if (netif_running(dev)) {
sky2_down(dev);
err = sky2_up(dev);
}
return err;
}
#ifdef CONFIG_PM
static void sky2_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
{
struct sky2_port *sky2 = netdev_priv(dev);
wol->supported = WAKE_MAGIC;
wol->wolopts = sky2->wol ? WAKE_MAGIC : 0;
}
static int sky2_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
if (wol->wolopts != WAKE_MAGIC && wol->wolopts != 0)
return -EOPNOTSUPP;
sky2->wol = wol->wolopts == WAKE_MAGIC;
if (sky2->wol) {
memcpy_toio(hw->regs + WOL_MAC_ADDR, dev->dev_addr, ETH_ALEN);
sky2_write16(hw, WOL_CTRL_STAT,
WOL_CTL_ENA_PME_ON_MAGIC_PKT |
WOL_CTL_ENA_MAGIC_PKT_UNIT);
} else
sky2_write16(hw, WOL_CTRL_STAT, WOL_CTL_DEFAULT);
return 0;
}
#endif
static void sky2_get_ringparam(struct net_device *dev,
struct ethtool_ringparam *ering)
{
struct sky2_port *sky2 = netdev_priv(dev);
ering->rx_max_pending = RX_MAX_PENDING;
ering->rx_mini_max_pending = 0;
ering->rx_jumbo_max_pending = 0;
ering->tx_max_pending = TX_RING_SIZE - 1;
ering->rx_pending = sky2->rx_pending;
ering->rx_mini_pending = 0;
ering->rx_jumbo_pending = 0;
ering->tx_pending = sky2->tx_pending;
}
static int sky2_set_ringparam(struct net_device *dev,
struct ethtool_ringparam *ering)
{
struct sky2_port *sky2 = netdev_priv(dev);
int err = 0;
if (ering->rx_pending > RX_MAX_PENDING ||
ering->rx_pending < 8 ||
ering->tx_pending < MAX_SKB_TX_LE ||
ering->tx_pending > TX_RING_SIZE - 1)
return -EINVAL;
if (netif_running(dev))
sky2_down(dev);
sky2->rx_pending = ering->rx_pending;
sky2->tx_pending = ering->tx_pending;
if (netif_running(dev))
err = sky2_up(dev);
return err;
}
static int sky2_get_regs_len(struct net_device *dev)
{
return 0x4000;
}
/*
* Returns copy of control register region
* Note: access to the RAM address register set will cause timeouts.
*/
static void sky2_get_regs(struct net_device *dev, struct ethtool_regs *regs,
void *p)
{
const struct sky2_port *sky2 = netdev_priv(dev);
const void __iomem *io = sky2->hw->regs;
BUG_ON(regs->len < B3_RI_WTO_R1);
regs->version = 1;
memset(p, 0, regs->len);
memcpy_fromio(p, io, B3_RAM_ADDR);
memcpy_fromio(p + B3_RI_WTO_R1,
io + B3_RI_WTO_R1,
regs->len - B3_RI_WTO_R1);
}
static struct ethtool_ops sky2_ethtool_ops = {
.get_settings = sky2_get_settings,
.set_settings = sky2_set_settings,
.get_drvinfo = sky2_get_drvinfo,
.get_msglevel = sky2_get_msglevel,
.set_msglevel = sky2_set_msglevel,
.nway_reset = sky2_nway_reset,
.get_regs_len = sky2_get_regs_len,
.get_regs = sky2_get_regs,
.get_link = ethtool_op_get_link,
.get_sg = ethtool_op_get_sg,
.set_sg = ethtool_op_set_sg,
.get_tx_csum = ethtool_op_get_tx_csum,
.set_tx_csum = ethtool_op_set_tx_csum,
.get_tso = ethtool_op_get_tso,
.set_tso = ethtool_op_set_tso,
.get_rx_csum = sky2_get_rx_csum,
.set_rx_csum = sky2_set_rx_csum,
.get_strings = sky2_get_strings,
.get_ringparam = sky2_get_ringparam,
.set_ringparam = sky2_set_ringparam,
.get_pauseparam = sky2_get_pauseparam,
.set_pauseparam = sky2_set_pauseparam,
#ifdef CONFIG_PM
.get_wol = sky2_get_wol,
.set_wol = sky2_set_wol,
#endif
.phys_id = sky2_phys_id,
.get_stats_count = sky2_get_stats_count,
.get_ethtool_stats = sky2_get_ethtool_stats,
.get_perm_addr = ethtool_op_get_perm_addr,
};
/* Initialize network device */
static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
unsigned port, int highmem)
{
struct sky2_port *sky2;
struct net_device *dev = alloc_etherdev(sizeof(*sky2));
if (!dev) {
printk(KERN_ERR "sky2 etherdev alloc failed");
return NULL;
}
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &hw->pdev->dev);
dev->irq = hw->pdev->irq;
dev->open = sky2_up;
dev->stop = sky2_down;
dev->do_ioctl = sky2_ioctl;
dev->hard_start_xmit = sky2_xmit_frame;
dev->get_stats = sky2_get_stats;
dev->set_multicast_list = sky2_set_multicast;
dev->set_mac_address = sky2_set_mac_address;
dev->change_mtu = sky2_change_mtu;
SET_ETHTOOL_OPS(dev, &sky2_ethtool_ops);
dev->tx_timeout = sky2_tx_timeout;
dev->watchdog_timeo = TX_WATCHDOG;
if (port == 0)
dev->poll = sky2_poll;
dev->weight = NAPI_WEIGHT;
#ifdef CONFIG_NET_POLL_CONTROLLER
dev->poll_controller = sky2_netpoll;
#endif
sky2 = netdev_priv(dev);
sky2->netdev = dev;
sky2->hw = hw;
sky2->msg_enable = netif_msg_init(debug, default_msg);
spin_lock_init(&sky2->tx_lock);
/* Auto speed and flow control */
sky2->autoneg = AUTONEG_ENABLE;
sky2->tx_pause = 0;
sky2->rx_pause = 1;
sky2->duplex = -1;
sky2->speed = -1;
sky2->advertising = sky2_supported_modes(hw);
sky2->rx_csum = 1;
tasklet_init(&sky2->phy_task, sky2_phy_task, (unsigned long)sky2);
sky2->tx_pending = TX_DEF_PENDING;
sky2->rx_pending = is_ec_a1(hw) ? 8 : RX_DEF_PENDING;
hw->dev[port] = dev;
sky2->port = port;
dev->features |= NETIF_F_LLTX;
if (hw->chip_id != CHIP_ID_YUKON_EC_U)
dev->features |= NETIF_F_TSO;
if (highmem)
dev->features |= NETIF_F_HIGHDMA;
dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG;
#ifdef SKY2_VLAN_TAG_USED
dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
dev->vlan_rx_register = sky2_vlan_rx_register;
dev->vlan_rx_kill_vid = sky2_vlan_rx_kill_vid;
#endif
/* read the mac address */
memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port * 8, ETH_ALEN);
memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
/* device is off until link detection */
netif_carrier_off(dev);
netif_stop_queue(dev);
return dev;
}
static inline void sky2_show_addr(struct net_device *dev)
{
const struct sky2_port *sky2 = netdev_priv(dev);
if (netif_msg_probe(sky2))
printk(KERN_INFO PFX "%s: addr %02x:%02x:%02x:%02x:%02x:%02x\n",
dev->name,
dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]);
}
static int __devinit sky2_probe(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
struct net_device *dev, *dev1 = NULL;
struct sky2_hw *hw;
int err, pm_cap, using_dac = 0;
err = pci_enable_device(pdev);
if (err) {
printk(KERN_ERR PFX "%s cannot enable PCI device\n",
pci_name(pdev));
goto err_out;
}
err = pci_request_regions(pdev, DRV_NAME);
if (err) {
printk(KERN_ERR PFX "%s cannot obtain PCI resources\n",
pci_name(pdev));
goto err_out;
}
pci_set_master(pdev);
/* Find power-management capability. */
pm_cap = pci_find_capability(pdev, PCI_CAP_ID_PM);
if (pm_cap == 0) {
printk(KERN_ERR PFX "Cannot find PowerManagement capability, "
"aborting.\n");
err = -EIO;
goto err_out_free_regions;
}
if (sizeof(dma_addr_t) > sizeof(u32)) {
err = pci_set_dma_mask(pdev, DMA_64BIT_MASK);
if (!err)
using_dac = 1;
}
if (!using_dac) {
err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (err) {
printk(KERN_ERR PFX "%s no usable DMA configuration\n",
pci_name(pdev));
goto err_out_free_regions;
}
}
#ifdef __BIG_ENDIAN
/* byte swap descriptors in hardware */
{
u32 reg;
pci_read_config_dword(pdev, PCI_DEV_REG2, &reg);
reg |= PCI_REV_DESC;
pci_write_config_dword(pdev, PCI_DEV_REG2, reg);
}
#endif
err = -ENOMEM;
hw = kmalloc(sizeof(*hw), GFP_KERNEL);
if (!hw) {
printk(KERN_ERR PFX "%s: cannot allocate hardware struct\n",
pci_name(pdev));
goto err_out_free_regions;
}
memset(hw, 0, sizeof(*hw));
hw->pdev = pdev;
spin_lock_init(&hw->phy_lock);
hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
if (!hw->regs) {
printk(KERN_ERR PFX "%s: cannot map device registers\n",
pci_name(pdev));
goto err_out_free_hw;
}
hw->pm_cap = pm_cap;
err = sky2_reset(hw);
if (err)
goto err_out_iounmap;
printk(KERN_INFO PFX "addr 0x%lx irq %d Yukon-%s (0x%x) rev %d\n",
pci_resource_start(pdev, 0), pdev->irq,
yukon_name[hw->chip_id - CHIP_ID_YUKON],
hw->chip_id, hw->chip_rev);
dev = sky2_init_netdev(hw, 0, using_dac);
if (!dev)
goto err_out_free_pci;
err = register_netdev(dev);
if (err) {
printk(KERN_ERR PFX "%s: cannot register net device\n",
pci_name(pdev));
goto err_out_free_netdev;
}
sky2_show_addr(dev);
if (hw->ports > 1 && (dev1 = sky2_init_netdev(hw, 1, using_dac))) {
if (register_netdev(dev1) == 0)
sky2_show_addr(dev1);
else {
/* Failure to register second port need not be fatal */
printk(KERN_WARNING PFX
"register of second port failed\n");
hw->dev[1] = NULL;
free_netdev(dev1);
}
}
err = request_irq(pdev->irq, sky2_intr, SA_SHIRQ, DRV_NAME, hw);
if (err) {
printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
pci_name(pdev), pdev->irq);
goto err_out_unregister;
}
hw->intr_mask = Y2_IS_BASE;
sky2_write32(hw, B0_IMSK, hw->intr_mask);
pci_set_drvdata(pdev, hw);
return 0;
err_out_unregister:
if (dev1) {
unregister_netdev(dev1);
free_netdev(dev1);
}
unregister_netdev(dev);
err_out_free_netdev:
free_netdev(dev);
err_out_free_pci:
sky2_write8(hw, B0_CTST, CS_RST_SET);
pci_free_consistent(hw->pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma);
err_out_iounmap:
iounmap(hw->regs);
err_out_free_hw:
kfree(hw);
err_out_free_regions:
pci_release_regions(pdev);
pci_disable_device(pdev);
err_out:
return err;
}
static void __devexit sky2_remove(struct pci_dev *pdev)
{
struct sky2_hw *hw = pci_get_drvdata(pdev);
struct net_device *dev0, *dev1;
if (!hw)
return;
dev0 = hw->dev[0];
dev1 = hw->dev[1];
if (dev1)
unregister_netdev(dev1);
unregister_netdev(dev0);
sky2_write32(hw, B0_IMSK, 0);
sky2_set_power_state(hw, PCI_D3hot);
sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
sky2_write8(hw, B0_CTST, CS_RST_SET);
sky2_read8(hw, B0_CTST);
free_irq(pdev->irq, hw);
pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma);
pci_release_regions(pdev);
pci_disable_device(pdev);
if (dev1)
free_netdev(dev1);
free_netdev(dev0);
iounmap(hw->regs);
kfree(hw);
pci_set_drvdata(pdev, NULL);
}
#ifdef CONFIG_PM
static int sky2_suspend(struct pci_dev *pdev, pm_message_t state)
{
struct sky2_hw *hw = pci_get_drvdata(pdev);
int i;
for (i = 0; i < 2; i++) {
struct net_device *dev = hw->dev[i];
if (dev) {
if (!netif_running(dev))
continue;
sky2_down(dev);
netif_device_detach(dev);
}
}
return sky2_set_power_state(hw, pci_choose_state(pdev, state));
}
static int sky2_resume(struct pci_dev *pdev)
{
struct sky2_hw *hw = pci_get_drvdata(pdev);
int i;
pci_restore_state(pdev);
pci_enable_wake(pdev, PCI_D0, 0);
sky2_set_power_state(hw, PCI_D0);
sky2_reset(hw);
for (i = 0; i < 2; i++) {
struct net_device *dev = hw->dev[i];
if (dev) {
if (netif_running(dev)) {
netif_device_attach(dev);
sky2_up(dev);
}
}
}
return 0;
}
#endif
static struct pci_driver sky2_driver = {
.name = DRV_NAME,
.id_table = sky2_id_table,
.probe = sky2_probe,
.remove = __devexit_p(sky2_remove),
#ifdef CONFIG_PM
.suspend = sky2_suspend,
.resume = sky2_resume,
#endif
};
static int __init sky2_init_module(void)
{
return pci_module_init(&sky2_driver);
}
static void __exit sky2_cleanup_module(void)
{
pci_unregister_driver(&sky2_driver);
}
module_init(sky2_init_module);
module_exit(sky2_cleanup_module);
MODULE_DESCRIPTION("Marvell Yukon 2 Gigabit Ethernet driver");
MODULE_AUTHOR("Stephen Hemminger <shemminger@osdl.org>");
MODULE_LICENSE("GPL");