forked from Minki/linux
a91f741589
Currently the setup code for the FEC multi-function pins on the ColdFire 528x has the addresses hard coded in the code. Use the register defines that already exist for this. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
107 lines
2.5 KiB
C
107 lines
2.5 KiB
C
/***************************************************************************/
|
|
|
|
/*
|
|
* linux/arch/m68knommu/platform/528x/config.c
|
|
*
|
|
* Sub-architcture dependent initialization code for the Freescale
|
|
* 5280, 5281 and 5282 CPUs.
|
|
*
|
|
* Copyright (C) 1999-2003, Greg Ungerer (gerg@snapgear.com)
|
|
* Copyright (C) 2001-2003, SnapGear Inc. (www.snapgear.com)
|
|
*/
|
|
|
|
/***************************************************************************/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/param.h>
|
|
#include <linux/init.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/io.h>
|
|
#include <asm/machdep.h>
|
|
#include <asm/coldfire.h>
|
|
#include <asm/mcfsim.h>
|
|
#include <asm/mcfuart.h>
|
|
|
|
/***************************************************************************/
|
|
|
|
#if IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI)
|
|
|
|
static void __init m528x_qspi_init(void)
|
|
{
|
|
/* setup Port QS for QSPI with gpio CS control */
|
|
__raw_writeb(0x07, MCFGPIO_PQSPAR);
|
|
}
|
|
|
|
#endif /* IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI) */
|
|
|
|
/***************************************************************************/
|
|
|
|
static void __init m528x_uarts_init(void)
|
|
{
|
|
u8 port;
|
|
|
|
/* make sure PUAPAR is set for UART0 and UART1 */
|
|
port = readb(MCF5282_GPIO_PUAPAR);
|
|
port |= 0x03 | (0x03 << 2);
|
|
writeb(port, MCFGPIO_PUAPAR);
|
|
}
|
|
|
|
/***************************************************************************/
|
|
|
|
static void __init m528x_fec_init(void)
|
|
{
|
|
u16 v16;
|
|
|
|
/* Set multi-function pins to ethernet mode for fec0 */
|
|
v16 = readw(MCFGPIO_PASPAR);
|
|
writew(v16 | 0xf00, MCFGPIO_PASPAR);
|
|
writeb(0xc0, MCFGPIO_PEHLPAR);
|
|
}
|
|
|
|
/***************************************************************************/
|
|
|
|
#ifdef CONFIG_WILDFIRE
|
|
void wildfire_halt(void)
|
|
{
|
|
writeb(0, 0x30000007);
|
|
writeb(0x2, 0x30000007);
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_WILDFIREMOD
|
|
void wildfiremod_halt(void)
|
|
{
|
|
printk(KERN_INFO "WildFireMod hibernating...\n");
|
|
|
|
/* Set portE.5 to Digital IO */
|
|
MCF5282_GPIO_PEPAR &= ~(1 << (5 * 2));
|
|
|
|
/* Make portE.5 an output */
|
|
MCF5282_GPIO_DDRE |= (1 << 5);
|
|
|
|
/* Now toggle portE.5 from low to high */
|
|
MCF5282_GPIO_PORTE &= ~(1 << 5);
|
|
MCF5282_GPIO_PORTE |= (1 << 5);
|
|
|
|
printk(KERN_EMERG "Failed to hibernate. Halting!\n");
|
|
}
|
|
#endif
|
|
|
|
void __init config_BSP(char *commandp, int size)
|
|
{
|
|
#ifdef CONFIG_WILDFIRE
|
|
mach_halt = wildfire_halt;
|
|
#endif
|
|
#ifdef CONFIG_WILDFIREMOD
|
|
mach_halt = wildfiremod_halt;
|
|
#endif
|
|
mach_sched_init = hw_timer_init;
|
|
m528x_uarts_init();
|
|
m528x_fec_init();
|
|
#if IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI)
|
|
m528x_qspi_init();
|
|
#endif
|
|
}
|
|
|
|
/***************************************************************************/
|