linux/drivers/net/sfc/falcon_boards.c
Ben Hutchings 5087b54ddc sfc: Remove boards.h, moving last remaining declaration to falcon.h
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-24 04:26:56 -07:00

752 lines
21 KiB
C

/****************************************************************************
* Driver for Solarflare Solarstorm network controllers and boards
* Copyright 2007-2008 Solarflare Communications Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published
* by the Free Software Foundation, incorporated herein by reference.
*/
#include <linux/rtnetlink.h>
#include "net_driver.h"
#include "phy.h"
#include "efx.h"
#include "falcon.h"
#include "falcon_hwdefs.h"
#include "falcon_io.h"
#include "workarounds.h"
/* Macros for unpacking the board revision */
/* The revision info is in host byte order. */
#define FALCON_BOARD_TYPE(_rev) (_rev >> 8)
#define FALCON_BOARD_MAJOR(_rev) ((_rev >> 4) & 0xf)
#define FALCON_BOARD_MINOR(_rev) (_rev & 0xf)
/* Board types */
#define FALCON_BOARD_SFE4001 0x01
#define FALCON_BOARD_SFE4002 0x02
#define FALCON_BOARD_SFN4111T 0x51
#define FALCON_BOARD_SFN4112F 0x52
/* Blink support. If the PHY has no auto-blink mode so we hang it off a timer */
#define BLINK_INTERVAL (HZ/2)
static void blink_led_timer(unsigned long context)
{
struct efx_nic *efx = (struct efx_nic *)context;
struct efx_blinker *bl = &efx->board_info.blinker;
efx->board_info.set_id_led(efx, bl->state);
bl->state = !bl->state;
if (bl->resubmit)
mod_timer(&bl->timer, jiffies + BLINK_INTERVAL);
}
static void board_blink(struct efx_nic *efx, bool blink)
{
struct efx_blinker *blinker = &efx->board_info.blinker;
/* The rtnl mutex serialises all ethtool ioctls, so
* nothing special needs doing here. */
if (blink) {
blinker->resubmit = true;
blinker->state = false;
setup_timer(&blinker->timer, blink_led_timer,
(unsigned long)efx);
mod_timer(&blinker->timer, jiffies + BLINK_INTERVAL);
} else {
blinker->resubmit = false;
if (blinker->timer.function)
del_timer_sync(&blinker->timer);
efx->board_info.init_leds(efx);
}
}
/*****************************************************************************
* Support for LM87 sensor chip used on several boards
*/
#define LM87_REG_ALARMS1 0x41
#define LM87_REG_ALARMS2 0x42
#define LM87_IN_LIMITS(nr, _min, _max) \
0x2B + (nr) * 2, _max, 0x2C + (nr) * 2, _min
#define LM87_AIN_LIMITS(nr, _min, _max) \
0x3B + (nr), _max, 0x1A + (nr), _min
#define LM87_TEMP_INT_LIMITS(_min, _max) \
0x39, _max, 0x3A, _min
#define LM87_TEMP_EXT1_LIMITS(_min, _max) \
0x37, _max, 0x38, _min
#define LM87_ALARM_TEMP_INT 0x10
#define LM87_ALARM_TEMP_EXT1 0x20
#if defined(CONFIG_SENSORS_LM87) || defined(CONFIG_SENSORS_LM87_MODULE)
static int efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info,
const u8 *reg_values)
{
struct i2c_client *client = i2c_new_device(&efx->i2c_adap, info);
int rc;
if (!client)
return -EIO;
while (*reg_values) {
u8 reg = *reg_values++;
u8 value = *reg_values++;
rc = i2c_smbus_write_byte_data(client, reg, value);
if (rc)
goto err;
}
efx->board_info.hwmon_client = client;
return 0;
err:
i2c_unregister_device(client);
return rc;
}
static void efx_fini_lm87(struct efx_nic *efx)
{
i2c_unregister_device(efx->board_info.hwmon_client);
}
static int efx_check_lm87(struct efx_nic *efx, unsigned mask)
{
struct i2c_client *client = efx->board_info.hwmon_client;
s32 alarms1, alarms2;
/* If link is up then do not monitor temperature */
if (EFX_WORKAROUND_7884(efx) && efx->link_up)
return 0;
alarms1 = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS1);
alarms2 = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS2);
if (alarms1 < 0)
return alarms1;
if (alarms2 < 0)
return alarms2;
alarms1 &= mask;
alarms2 &= mask >> 8;
if (alarms1 || alarms2) {
EFX_ERR(efx,
"LM87 detected a hardware failure (status %02x:%02x)"
"%s%s\n",
alarms1, alarms2,
(alarms1 & LM87_ALARM_TEMP_INT) ? " INTERNAL" : "",
(alarms1 & LM87_ALARM_TEMP_EXT1) ? " EXTERNAL" : "");
return -ERANGE;
}
return 0;
}
#else /* !CONFIG_SENSORS_LM87 */
static inline int
efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info,
const u8 *reg_values)
{
return 0;
}
static inline void efx_fini_lm87(struct efx_nic *efx)
{
}
static inline int efx_check_lm87(struct efx_nic *efx, unsigned mask)
{
return 0;
}
#endif /* CONFIG_SENSORS_LM87 */
/*****************************************************************************
* Support for the SFE4001 and SFN4111T NICs.
*
* The SFE4001 does not power-up fully at reset due to its high power
* consumption. We control its power via a PCA9539 I/O expander.
* Both boards have a MAX6647 temperature monitor which we expose to
* the lm90 driver.
*
* This also provides minimal support for reflashing the PHY, which is
* initiated by resetting it with the FLASH_CFG_1 pin pulled down.
* On SFE4001 rev A2 and later this is connected to the 3V3X output of
* the IO-expander; on the SFN4111T it is connected to Falcon's GPIO3.
* We represent reflash mode as PHY_MODE_SPECIAL and make it mutually
* exclusive with the network device being open.
*/
/**************************************************************************
* Support for I2C IO Expander device on SFE40001
*/
#define PCA9539 0x74
#define P0_IN 0x00
#define P0_OUT 0x02
#define P0_INVERT 0x04
#define P0_CONFIG 0x06
#define P0_EN_1V0X_LBN 0
#define P0_EN_1V0X_WIDTH 1
#define P0_EN_1V2_LBN 1
#define P0_EN_1V2_WIDTH 1
#define P0_EN_2V5_LBN 2
#define P0_EN_2V5_WIDTH 1
#define P0_EN_3V3X_LBN 3
#define P0_EN_3V3X_WIDTH 1
#define P0_EN_5V_LBN 4
#define P0_EN_5V_WIDTH 1
#define P0_SHORTEN_JTAG_LBN 5
#define P0_SHORTEN_JTAG_WIDTH 1
#define P0_X_TRST_LBN 6
#define P0_X_TRST_WIDTH 1
#define P0_DSP_RESET_LBN 7
#define P0_DSP_RESET_WIDTH 1
#define P1_IN 0x01
#define P1_OUT 0x03
#define P1_INVERT 0x05
#define P1_CONFIG 0x07
#define P1_AFE_PWD_LBN 0
#define P1_AFE_PWD_WIDTH 1
#define P1_DSP_PWD25_LBN 1
#define P1_DSP_PWD25_WIDTH 1
#define P1_RESERVED_LBN 2
#define P1_RESERVED_WIDTH 2
#define P1_SPARE_LBN 4
#define P1_SPARE_WIDTH 4
/* Temperature Sensor */
#define MAX664X_REG_RSL 0x02
#define MAX664X_REG_WLHO 0x0B
static void sfe4001_poweroff(struct efx_nic *efx)
{
struct i2c_client *ioexp_client = efx->board_info.ioexp_client;
struct i2c_client *hwmon_client = efx->board_info.hwmon_client;
/* Turn off all power rails and disable outputs */
i2c_smbus_write_byte_data(ioexp_client, P0_OUT, 0xff);
i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG, 0xff);
i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0xff);
/* Clear any over-temperature alert */
i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL);
}
static int sfe4001_poweron(struct efx_nic *efx)
{
struct i2c_client *hwmon_client = efx->board_info.hwmon_client;
struct i2c_client *ioexp_client = efx->board_info.ioexp_client;
unsigned int i, j;
int rc;
u8 out;
/* Clear any previous over-temperature alert */
rc = i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL);
if (rc < 0)
return rc;
/* Enable port 0 and port 1 outputs on IO expander */
rc = i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0x00);
if (rc)
return rc;
rc = i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG,
0xff & ~(1 << P1_SPARE_LBN));
if (rc)
goto fail_on;
/* If PHY power is on, turn it all off and wait 1 second to
* ensure a full reset.
*/
rc = i2c_smbus_read_byte_data(ioexp_client, P0_OUT);
if (rc < 0)
goto fail_on;
out = 0xff & ~((0 << P0_EN_1V2_LBN) | (0 << P0_EN_2V5_LBN) |
(0 << P0_EN_3V3X_LBN) | (0 << P0_EN_5V_LBN) |
(0 << P0_EN_1V0X_LBN));
if (rc != out) {
EFX_INFO(efx, "power-cycling PHY\n");
rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
if (rc)
goto fail_on;
schedule_timeout_uninterruptible(HZ);
}
for (i = 0; i < 20; ++i) {
/* Turn on 1.2V, 2.5V, 3.3V and 5V power rails */
out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) |
(1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) |
(1 << P0_X_TRST_LBN));
if (efx->phy_mode & PHY_MODE_SPECIAL)
out |= 1 << P0_EN_3V3X_LBN;
rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
if (rc)
goto fail_on;
msleep(10);
/* Turn on 1V power rail */
out &= ~(1 << P0_EN_1V0X_LBN);
rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
if (rc)
goto fail_on;
EFX_INFO(efx, "waiting for DSP boot (attempt %d)...\n", i);
/* In flash config mode, DSP does not turn on AFE, so
* just wait 1 second.
*/
if (efx->phy_mode & PHY_MODE_SPECIAL) {
schedule_timeout_uninterruptible(HZ);
return 0;
}
for (j = 0; j < 10; ++j) {
msleep(100);
/* Check DSP has asserted AFE power line */
rc = i2c_smbus_read_byte_data(ioexp_client, P1_IN);
if (rc < 0)
goto fail_on;
if (rc & (1 << P1_AFE_PWD_LBN))
return 0;
}
}
EFX_INFO(efx, "timed out waiting for DSP boot\n");
rc = -ETIMEDOUT;
fail_on:
sfe4001_poweroff(efx);
return rc;
}
static int sfn4111t_reset(struct efx_nic *efx)
{
efx_oword_t reg;
/* GPIO 3 and the GPIO register are shared with I2C, so block that */
mutex_lock(&efx->i2c_adap.bus_lock);
/* Pull RST_N (GPIO 2) low then let it up again, setting the
* FLASH_CFG_1 strap (GPIO 3) appropriately. Only change the
* output enables; the output levels should always be 0 (low)
* and we rely on external pull-ups. */
falcon_read(efx, &reg, GPIO_CTL_REG_KER);
EFX_SET_OWORD_FIELD(reg, GPIO2_OEN, true);
falcon_write(efx, &reg, GPIO_CTL_REG_KER);
msleep(1000);
EFX_SET_OWORD_FIELD(reg, GPIO2_OEN, false);
EFX_SET_OWORD_FIELD(reg, GPIO3_OEN,
!!(efx->phy_mode & PHY_MODE_SPECIAL));
falcon_write(efx, &reg, GPIO_CTL_REG_KER);
msleep(1);
mutex_unlock(&efx->i2c_adap.bus_lock);
ssleep(1);
return 0;
}
static ssize_t show_phy_flash_cfg(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev));
return sprintf(buf, "%d\n", !!(efx->phy_mode & PHY_MODE_SPECIAL));
}
static ssize_t set_phy_flash_cfg(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev));
enum efx_phy_mode old_mode, new_mode;
int err;
rtnl_lock();
old_mode = efx->phy_mode;
if (count == 0 || *buf == '0')
new_mode = old_mode & ~PHY_MODE_SPECIAL;
else
new_mode = PHY_MODE_SPECIAL;
if (old_mode == new_mode) {
err = 0;
} else if (efx->state != STATE_RUNNING || netif_running(efx->net_dev)) {
err = -EBUSY;
} else {
/* Reset the PHY, reconfigure the MAC and enable/disable
* MAC stats accordingly. */
efx->phy_mode = new_mode;
if (new_mode & PHY_MODE_SPECIAL)
efx_stats_disable(efx);
if (efx->board_info.type == FALCON_BOARD_SFE4001)
err = sfe4001_poweron(efx);
else
err = sfn4111t_reset(efx);
efx_reconfigure_port(efx);
if (!(new_mode & PHY_MODE_SPECIAL))
efx_stats_enable(efx);
}
rtnl_unlock();
return err ? err : count;
}
static DEVICE_ATTR(phy_flash_cfg, 0644, show_phy_flash_cfg, set_phy_flash_cfg);
static void sfe4001_fini(struct efx_nic *efx)
{
EFX_INFO(efx, "%s\n", __func__);
device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
sfe4001_poweroff(efx);
i2c_unregister_device(efx->board_info.ioexp_client);
i2c_unregister_device(efx->board_info.hwmon_client);
}
static int sfe4001_check_hw(struct efx_nic *efx)
{
s32 status;
/* If XAUI link is up then do not monitor */
if (EFX_WORKAROUND_7884(efx) && efx->mac_up)
return 0;
/* Check the powered status of the PHY. Lack of power implies that
* the MAX6647 has shut down power to it, probably due to a temp.
* alarm. Reading the power status rather than the MAX6647 status
* directly because the later is read-to-clear and would thus
* start to power up the PHY again when polled, causing us to blip
* the power undesirably.
* We know we can read from the IO expander because we did
* it during power-on. Assume failure now is bad news. */
status = i2c_smbus_read_byte_data(efx->board_info.ioexp_client, P1_IN);
if (status >= 0 &&
(status & ((1 << P1_AFE_PWD_LBN) | (1 << P1_DSP_PWD25_LBN))) != 0)
return 0;
/* Use board power control, not PHY power control */
sfe4001_poweroff(efx);
efx->phy_mode = PHY_MODE_OFF;
return (status < 0) ? -EIO : -ERANGE;
}
static struct i2c_board_info sfe4001_hwmon_info = {
I2C_BOARD_INFO("max6647", 0x4e),
};
/* This board uses an I2C expander to provider power to the PHY, which needs to
* be turned on before the PHY can be used.
* Context: Process context, rtnl lock held
*/
static int sfe4001_init(struct efx_nic *efx)
{
int rc;
#if defined(CONFIG_SENSORS_LM90) || defined(CONFIG_SENSORS_LM90_MODULE)
efx->board_info.hwmon_client =
i2c_new_device(&efx->i2c_adap, &sfe4001_hwmon_info);
#else
efx->board_info.hwmon_client =
i2c_new_dummy(&efx->i2c_adap, sfe4001_hwmon_info.addr);
#endif
if (!efx->board_info.hwmon_client)
return -EIO;
/* Raise board/PHY high limit from 85 to 90 degrees Celsius */
rc = i2c_smbus_write_byte_data(efx->board_info.hwmon_client,
MAX664X_REG_WLHO, 90);
if (rc)
goto fail_hwmon;
efx->board_info.ioexp_client = i2c_new_dummy(&efx->i2c_adap, PCA9539);
if (!efx->board_info.ioexp_client) {
rc = -EIO;
goto fail_hwmon;
}
/* 10Xpress has fixed-function LED pins, so there is no board-specific
* blink code. */
efx->board_info.blink = tenxpress_phy_blink;
efx->board_info.monitor = sfe4001_check_hw;
efx->board_info.fini = sfe4001_fini;
if (efx->phy_mode & PHY_MODE_SPECIAL) {
/* PHY won't generate a 156.25 MHz clock and MAC stats fetch
* will fail. */
efx_stats_disable(efx);
}
rc = sfe4001_poweron(efx);
if (rc)
goto fail_ioexp;
rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
if (rc)
goto fail_on;
EFX_INFO(efx, "PHY is powered on\n");
return 0;
fail_on:
sfe4001_poweroff(efx);
fail_ioexp:
i2c_unregister_device(efx->board_info.ioexp_client);
fail_hwmon:
i2c_unregister_device(efx->board_info.hwmon_client);
return rc;
}
static int sfn4111t_check_hw(struct efx_nic *efx)
{
s32 status;
/* If XAUI link is up then do not monitor */
if (EFX_WORKAROUND_7884(efx) && efx->mac_up)
return 0;
/* Test LHIGH, RHIGH, FAULT, EOT and IOT alarms */
status = i2c_smbus_read_byte_data(efx->board_info.hwmon_client,
MAX664X_REG_RSL);
if (status < 0)
return -EIO;
if (status & 0x57)
return -ERANGE;
return 0;
}
static void sfn4111t_fini(struct efx_nic *efx)
{
EFX_INFO(efx, "%s\n", __func__);
device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
i2c_unregister_device(efx->board_info.hwmon_client);
}
static struct i2c_board_info sfn4111t_a0_hwmon_info = {
I2C_BOARD_INFO("max6647", 0x4e),
};
static struct i2c_board_info sfn4111t_r5_hwmon_info = {
I2C_BOARD_INFO("max6646", 0x4d),
};
static int sfn4111t_init(struct efx_nic *efx)
{
int i = 0;
int rc;
efx->board_info.hwmon_client =
i2c_new_device(&efx->i2c_adap,
(efx->board_info.minor < 5) ?
&sfn4111t_a0_hwmon_info :
&sfn4111t_r5_hwmon_info);
if (!efx->board_info.hwmon_client)
return -EIO;
efx->board_info.blink = tenxpress_phy_blink;
efx->board_info.monitor = sfn4111t_check_hw;
efx->board_info.fini = sfn4111t_fini;
rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
if (rc)
goto fail_hwmon;
do {
if (efx->phy_mode & PHY_MODE_SPECIAL) {
/* PHY may not generate a 156.25 MHz clock and MAC
* stats fetch will fail. */
efx_stats_disable(efx);
sfn4111t_reset(efx);
}
rc = sft9001_wait_boot(efx);
if (rc == 0)
return 0;
efx->phy_mode = PHY_MODE_SPECIAL;
} while (rc == -EINVAL && ++i < 2);
device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
fail_hwmon:
i2c_unregister_device(efx->board_info.hwmon_client);
return rc;
}
/*****************************************************************************
* Support for the SFE4002
*
*/
static u8 sfe4002_lm87_channel = 0x03; /* use AIN not FAN inputs */
static const u8 sfe4002_lm87_regs[] = {
LM87_IN_LIMITS(0, 0x83, 0x91), /* 2.5V: 1.8V +/- 5% */
LM87_IN_LIMITS(1, 0x51, 0x5a), /* Vccp1: 1.2V +/- 5% */
LM87_IN_LIMITS(2, 0xb6, 0xca), /* 3.3V: 3.3V +/- 5% */
LM87_IN_LIMITS(3, 0xb0, 0xc9), /* 5V: 4.6-5.2V */
LM87_IN_LIMITS(4, 0xb0, 0xe0), /* 12V: 11-14V */
LM87_IN_LIMITS(5, 0x44, 0x4b), /* Vccp2: 1.0V +/- 5% */
LM87_AIN_LIMITS(0, 0xa0, 0xb2), /* AIN1: 1.66V +/- 5% */
LM87_AIN_LIMITS(1, 0x91, 0xa1), /* AIN2: 1.5V +/- 5% */
LM87_TEMP_INT_LIMITS(10, 60), /* board */
LM87_TEMP_EXT1_LIMITS(10, 70), /* Falcon */
0
};
static struct i2c_board_info sfe4002_hwmon_info = {
I2C_BOARD_INFO("lm87", 0x2e),
.platform_data = &sfe4002_lm87_channel,
};
/****************************************************************************/
/* LED allocations. Note that on rev A0 boards the schematic and the reality
* differ: red and green are swapped. Below is the fixed (A1) layout (there
* are only 3 A0 boards in existence, so no real reason to make this
* conditional).
*/
#define SFE4002_FAULT_LED (2) /* Red */
#define SFE4002_RX_LED (0) /* Green */
#define SFE4002_TX_LED (1) /* Amber */
static void sfe4002_init_leds(struct efx_nic *efx)
{
/* Set the TX and RX LEDs to reflect status and activity, and the
* fault LED off */
xfp_set_led(efx, SFE4002_TX_LED,
QUAKE_LED_TXLINK | QUAKE_LED_LINK_ACTSTAT);
xfp_set_led(efx, SFE4002_RX_LED,
QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACTSTAT);
xfp_set_led(efx, SFE4002_FAULT_LED, QUAKE_LED_OFF);
}
static void sfe4002_set_id_led(struct efx_nic *efx, bool state)
{
xfp_set_led(efx, SFE4002_FAULT_LED, state ? QUAKE_LED_ON :
QUAKE_LED_OFF);
}
static int sfe4002_check_hw(struct efx_nic *efx)
{
/* A0 board rev. 4002s report a temperature fault the whole time
* (bad sensor) so we mask it out. */
unsigned alarm_mask =
(efx->board_info.major == 0 && efx->board_info.minor == 0) ?
~LM87_ALARM_TEMP_EXT1 : ~0;
return efx_check_lm87(efx, alarm_mask);
}
static int sfe4002_init(struct efx_nic *efx)
{
int rc = efx_init_lm87(efx, &sfe4002_hwmon_info, sfe4002_lm87_regs);
if (rc)
return rc;
efx->board_info.monitor = sfe4002_check_hw;
efx->board_info.init_leds = sfe4002_init_leds;
efx->board_info.set_id_led = sfe4002_set_id_led;
efx->board_info.blink = board_blink;
efx->board_info.fini = efx_fini_lm87;
return 0;
}
/*****************************************************************************
* Support for the SFN4112F
*
*/
static u8 sfn4112f_lm87_channel = 0x03; /* use AIN not FAN inputs */
static const u8 sfn4112f_lm87_regs[] = {
LM87_IN_LIMITS(0, 0x83, 0x91), /* 2.5V: 1.8V +/- 5% */
LM87_IN_LIMITS(1, 0x51, 0x5a), /* Vccp1: 1.2V +/- 5% */
LM87_IN_LIMITS(2, 0xb6, 0xca), /* 3.3V: 3.3V +/- 5% */
LM87_IN_LIMITS(4, 0xb0, 0xe0), /* 12V: 11-14V */
LM87_IN_LIMITS(5, 0x44, 0x4b), /* Vccp2: 1.0V +/- 5% */
LM87_AIN_LIMITS(1, 0x91, 0xa1), /* AIN2: 1.5V +/- 5% */
LM87_TEMP_INT_LIMITS(10, 60), /* board */
LM87_TEMP_EXT1_LIMITS(10, 70), /* Falcon */
0
};
static struct i2c_board_info sfn4112f_hwmon_info = {
I2C_BOARD_INFO("lm87", 0x2e),
.platform_data = &sfn4112f_lm87_channel,
};
#define SFN4112F_ACT_LED 0
#define SFN4112F_LINK_LED 1
static void sfn4112f_init_leds(struct efx_nic *efx)
{
xfp_set_led(efx, SFN4112F_ACT_LED,
QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACT);
xfp_set_led(efx, SFN4112F_LINK_LED,
QUAKE_LED_RXLINK | QUAKE_LED_LINK_STAT);
}
static void sfn4112f_set_id_led(struct efx_nic *efx, bool state)
{
xfp_set_led(efx, SFN4112F_LINK_LED,
state ? QUAKE_LED_ON : QUAKE_LED_OFF);
}
static int sfn4112f_check_hw(struct efx_nic *efx)
{
/* Mask out unused sensors */
return efx_check_lm87(efx, ~0x48);
}
static int sfn4112f_init(struct efx_nic *efx)
{
int rc = efx_init_lm87(efx, &sfn4112f_hwmon_info, sfn4112f_lm87_regs);
if (rc)
return rc;
efx->board_info.monitor = sfn4112f_check_hw;
efx->board_info.init_leds = sfn4112f_init_leds;
efx->board_info.set_id_led = sfn4112f_set_id_led;
efx->board_info.blink = board_blink;
efx->board_info.fini = efx_fini_lm87;
return 0;
}
/* This will get expanded as board-specific details get moved out of the
* PHY drivers. */
struct falcon_board_data {
u8 type;
const char *ref_model;
const char *gen_type;
int (*init) (struct efx_nic *nic);
};
static struct falcon_board_data board_data[] = {
{ FALCON_BOARD_SFE4001, "SFE4001", "10GBASE-T adapter", sfe4001_init },
{ FALCON_BOARD_SFE4002, "SFE4002", "XFP adapter", sfe4002_init },
{ FALCON_BOARD_SFN4111T, "SFN4111T", "100/1000/10GBASE-T adapter",
sfn4111t_init },
{ FALCON_BOARD_SFN4112F, "SFN4112F", "SFP+ adapter",
sfn4112f_init },
};
void falcon_probe_board(struct efx_nic *efx, u16 revision_info)
{
struct falcon_board_data *data = NULL;
int i;
efx->board_info.type = FALCON_BOARD_TYPE(revision_info);
efx->board_info.major = FALCON_BOARD_MAJOR(revision_info);
efx->board_info.minor = FALCON_BOARD_MINOR(revision_info);
for (i = 0; i < ARRAY_SIZE(board_data); i++)
if (board_data[i].type == efx->board_info.type)
data = &board_data[i];
if (data) {
EFX_INFO(efx, "board is %s rev %c%d\n",
(efx->pci_dev->subsystem_vendor == EFX_VENDID_SFC)
? data->ref_model : data->gen_type,
'A' + efx->board_info.major, efx->board_info.minor);
efx->board_info.init = data->init;
} else {
EFX_ERR(efx, "unknown board type %d\n", efx->board_info.type);
}
}