forked from Minki/linux
9b3452d1fa
This driver is currently used by musb' cppi41 couter part. I may merge both dma engine user of musb at some point but not just yet. The driver seems to work in RX/TX mode in host mode, tested on mass storage. I increaed the size of the TX / RX transfers and waited for the core code to cancel a transfers and it seems to recover. v2..3: - use mall transfers on RX side and check data toggle. - use rndis mode on tx side so we haveon interrupt for 4096 transfers. - remove custom "transferred" hack and use dmaengine_tx_status() to compute the total amount of data that has been transferred. - cancel transfers and reclaim descriptors v1..v2: - RX path added - dma mode 0 & 1 is working - device tree nodes re-created. Cc: Vinod Koul <vinod.koul@intel.com> Cc: Dan Williams <djbw@fb.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
36 lines
1.3 KiB
Makefile
36 lines
1.3 KiB
Makefile
#
|
|
# for USB OTG silicon based on Mentor Graphics INVENTRA designs
|
|
#
|
|
|
|
obj-$(CONFIG_USB_MUSB_HDRC) += musb_hdrc.o
|
|
|
|
musb_hdrc-y := musb_core.o
|
|
|
|
musb_hdrc-$(CONFIG_USB_MUSB_HOST)$(CONFIG_USB_MUSB_DUAL_ROLE) += musb_virthub.o musb_host.o
|
|
musb_hdrc-$(CONFIG_USB_MUSB_GADGET)$(CONFIG_USB_MUSB_DUAL_ROLE) += musb_gadget_ep0.o musb_gadget.o
|
|
musb_hdrc-$(CONFIG_DEBUG_FS) += musb_debugfs.o
|
|
|
|
# Hardware Glue Layer
|
|
obj-$(CONFIG_USB_MUSB_OMAP2PLUS) += omap2430.o
|
|
obj-$(CONFIG_USB_MUSB_AM35X) += am35x.o
|
|
obj-$(CONFIG_USB_MUSB_DSPS) += musb_dsps.o
|
|
obj-$(CONFIG_USB_MUSB_TUSB6010) += tusb6010.o
|
|
obj-$(CONFIG_USB_MUSB_DAVINCI) += davinci.o
|
|
obj-$(CONFIG_USB_MUSB_DA8XX) += da8xx.o
|
|
obj-$(CONFIG_USB_MUSB_BLACKFIN) += blackfin.o
|
|
obj-$(CONFIG_USB_MUSB_UX500) += ux500.o
|
|
|
|
|
|
obj-$(CONFIG_USB_MUSB_AM335X_CHILD) += musb_am335x.o
|
|
|
|
# the kconfig must guarantee that only one of the
|
|
# possible I/O schemes will be enabled at a time ...
|
|
# PIO only, or DMA (several potential schemes).
|
|
# though PIO is always there to back up DMA, and for ep0
|
|
|
|
musb_hdrc-$(CONFIG_USB_INVENTRA_DMA) += musbhsdma.o
|
|
musb_hdrc-$(CONFIG_USB_TI_CPPI_DMA) += cppi_dma.o
|
|
musb_hdrc-$(CONFIG_USB_TUSB_OMAP_DMA) += tusb6010_omap.o
|
|
musb_hdrc-$(CONFIG_USB_UX500_DMA) += ux500_dma.o
|
|
musb_hdrc-$(CONFIG_USB_TI_CPPI41_DMA) += musb_cppi41.o
|