forked from Minki/linux
3b76df4b1e
This document defines the binding for a component that loads firmware and control the life cycle of a self-authenticating Qualcomm Hexagon core. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
138 lines
3.3 KiB
Plaintext
138 lines
3.3 KiB
Plaintext
Qualcomm Hexagon Peripheral Image Loader
|
|
|
|
This document defines the binding for a component that loads and boots firmware
|
|
on the Qualcomm Hexagon core.
|
|
|
|
- compatible:
|
|
Usage: required
|
|
Value type: <string>
|
|
Definition: must be one of:
|
|
"qcom,q6v5-pil"
|
|
|
|
- reg:
|
|
Usage: required
|
|
Value type: <prop-encoded-array>
|
|
Definition: must specify the base address and size of the qdsp6 and
|
|
rmb register blocks
|
|
|
|
- reg-names:
|
|
Usage: required
|
|
Value type: <stringlist>
|
|
Definition: must be "q6dsp" and "rmb"
|
|
|
|
- interrupts-extended:
|
|
Usage: required
|
|
Value type: <prop-encoded-array>
|
|
Definition: must list the watchdog, fatal IRQs ready, handover and
|
|
stop-ack IRQs
|
|
|
|
- interrupt-names:
|
|
Usage: required
|
|
Value type: <stringlist>
|
|
Definition: must be "wdog", "fatal", "ready", "handover", "stop-ack"
|
|
|
|
- clocks:
|
|
Usage: required
|
|
Value type: <phandle>
|
|
Definition: reference to the iface, bus and mem clocks to be held on
|
|
behalf of the booting of the Hexagon core
|
|
|
|
- clock-names:
|
|
Usage: required
|
|
Value type: <stringlist>
|
|
Definition: must be "iface", "bus", "mem"
|
|
|
|
- resets:
|
|
Usage: required
|
|
Value type: <phandle>
|
|
Definition: reference to the reset-controller for the modem sub-system
|
|
|
|
- reset-names:
|
|
Usage: required
|
|
Value type: <stringlist>
|
|
Definition: must be "mss_restart"
|
|
|
|
- cx-supply:
|
|
- mss-supply:
|
|
- mx-supply:
|
|
- pll-supply:
|
|
Usage: required
|
|
Value type: <phandle>
|
|
Definition: reference to the regulators to be held on behalf of the
|
|
booting of the Hexagon core
|
|
|
|
- qcom,smem-states:
|
|
Usage: required
|
|
Value type: <phandle>
|
|
Definition: reference to the smem state for requesting the Hexagon to
|
|
shut down
|
|
|
|
- qcom,smem-state-names:
|
|
Usage: required
|
|
Value type: <stringlist>
|
|
Definition: must be "stop"
|
|
|
|
- qcom,halt-regs:
|
|
Usage: required
|
|
Value type: <prop-encoded-array>
|
|
Definition: a phandle reference to a syscon representing TCSR followed
|
|
by the three offsets within syscon for q6, modem and nc
|
|
halt registers.
|
|
|
|
= SUBNODES:
|
|
The Hexagon node must contain two subnodes, named "mba" and "mpss" representing
|
|
the memory regions used by the Hexagon firmware. Each sub-node must contain:
|
|
|
|
- memory-region:
|
|
Usage: required
|
|
Value type: <phandle>
|
|
Definition: reference to the reserved-memory for the region
|
|
|
|
= EXAMPLE
|
|
The following example describes the resources needed to boot control the
|
|
Hexagon, as it is found on MSM8974 boards.
|
|
|
|
modem-rproc@fc880000 {
|
|
compatible = "qcom,q6v5-pil";
|
|
reg = <0xfc880000 0x100>,
|
|
<0xfc820000 0x020>;
|
|
reg-names = "qdsp6", "rmb";
|
|
|
|
interrupts-extended = <&intc 0 24 1>,
|
|
<&modem_smp2p_in 0 0>,
|
|
<&modem_smp2p_in 1 0>,
|
|
<&modem_smp2p_in 2 0>,
|
|
<&modem_smp2p_in 3 0>;
|
|
interrupt-names = "wdog",
|
|
"fatal",
|
|
"ready",
|
|
"handover",
|
|
"stop-ack";
|
|
|
|
clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
|
|
<&gcc GCC_MSS_CFG_AHB_CLK>,
|
|
<&gcc GCC_BOOT_ROM_AHB_CLK>;
|
|
clock-names = "iface", "bus", "mem";
|
|
|
|
qcom,halt-regs = <&tcsr_mutex_block 0x1180 0x1200 0x1280>;
|
|
|
|
resets = <&gcc GCC_MSS_RESTART>;
|
|
reset-names = "mss_restart";
|
|
|
|
cx-supply = <&pm8841_s2>;
|
|
mss-supply = <&pm8841_s3>;
|
|
mx-supply = <&pm8841_s1>;
|
|
pll-supply = <&pm8941_l12>;
|
|
|
|
qcom,smem-states = <&modem_smp2p_out 0>;
|
|
qcom,smem-state-names = "stop";
|
|
|
|
mba {
|
|
memory-region = <&mba_region>;
|
|
};
|
|
|
|
mpss {
|
|
memory-region = <&mpss_region>;
|
|
};
|
|
};
|