forked from Minki/linux
1da177e4c3
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
1121 lines
40 KiB
Plaintext
1121 lines
40 KiB
Plaintext
# drivers/sound/Config.in
|
|
#
|
|
# 18 Apr 1998, Michael Elizabeth Chastain, <mailto:mec@shout.net>
|
|
# More hacking for modularisation.
|
|
#
|
|
# Prompt user for primary drivers.
|
|
config SOUND_BT878
|
|
tristate "BT878 audio dma"
|
|
depends on SOUND_PRIME!=n && SOUND
|
|
---help---
|
|
Audio DMA support for bt878 based grabber boards. As you might have
|
|
already noticed, bt878 is listed with two functions in /proc/pci.
|
|
Function 0 does the video stuff (bt848 compatible), function 1 does
|
|
the same for audio data. This is a driver for the audio part of
|
|
the chip. If you say 'Y' here you get a oss-compatible dsp device
|
|
where you can record from. If you want just watch TV you probably
|
|
don't need this driver as most TV cards handle sound with a short
|
|
cable from the TV card to your sound card's line-in.
|
|
|
|
To compile this driver as a module, choose M here: the module will
|
|
be called btaudio.
|
|
|
|
config SOUND_CMPCI
|
|
tristate "C-Media PCI (CMI8338/8738)"
|
|
depends on SOUND_PRIME!=n && SOUND && PCI
|
|
help
|
|
Say Y or M if you have a PCI sound card using the CMI8338
|
|
or the CMI8738 chipset. Data on these chips are available at
|
|
<http://www.cmedia.com.tw/>.
|
|
|
|
A userspace utility to control some internal registers of these
|
|
chips is available at
|
|
<http://member.nifty.ne.jp/Breeze/softwares/unix/cmictl-e.html>.
|
|
|
|
config SOUND_CMPCI_FM
|
|
bool "Enable legacy FM"
|
|
depends on SOUND_CMPCI && X86
|
|
help
|
|
Say Y here to enable the legacy FM (frequency-modulation) synthesizer
|
|
support on a card using the CMI8338 or CMI8378 chipset. Even it is
|
|
enabled, you need to set fmio as proper value to enable it.
|
|
Say N here if you don't need this.
|
|
|
|
config SOUND_CMPCI_MIDI
|
|
bool "Enable legacy MPU-401"
|
|
depends on SOUND_CMPCI && X86
|
|
help
|
|
Say Y here to enable the legacy MPU401 MIDI synthesizer support on a
|
|
card using the CMI8338 or CMI8378 chipset. Even it is enabled,
|
|
you need to set mpuio as proper value to enable it.
|
|
Say N here if you don't need this.
|
|
|
|
config SOUND_CMPCI_JOYSTICK
|
|
bool "Enable joystick"
|
|
depends on SOUND_CMPCI && X86
|
|
help
|
|
Say Y here in order to enable the joystick port on a sound card using
|
|
the CMI8338 or the CMI8738 chipset. You need to config the
|
|
gameport support and set joystick parameter as 1 to use it.
|
|
Say N here if you don't need this.
|
|
|
|
config SOUND_EMU10K1
|
|
tristate "Creative SBLive! (EMU10K1)"
|
|
depends on SOUND_PRIME!=n && SOUND && PCI
|
|
---help---
|
|
Say Y or M if you have a PCI sound card using the EMU10K1 chipset,
|
|
such as the Creative SBLive!, SB PCI512 or Emu-APS.
|
|
|
|
For more information on this driver and the degree of support for
|
|
the different card models please check:
|
|
|
|
<http://sourceforge.net/projects/emu10k1/>
|
|
|
|
It is now possible to load dsp microcode patches into the EMU10K1
|
|
chip. These patches are used to implement real time sound
|
|
processing effects which include for example: signal routing,
|
|
bass/treble control, AC3 passthrough, ...
|
|
Userspace tools to create new patches and load/unload them can be
|
|
found in the emu-tools package at the above URL.
|
|
|
|
config MIDI_EMU10K1
|
|
bool "Creative SBLive! MIDI (EXPERIMENTAL)"
|
|
depends on SOUND_EMU10K1 && EXPERIMENTAL
|
|
help
|
|
Say Y if you want to be able to use the OSS /dev/sequencer
|
|
interface. This code is still experimental.
|
|
|
|
config SOUND_FUSION
|
|
tristate "Crystal SoundFusion (CS4280/461x)"
|
|
depends on SOUND_PRIME!=n && SOUND
|
|
help
|
|
This module drives the Crystal SoundFusion devices (CS4280/46xx
|
|
series) when wired as native sound drivers with AC97 codecs. If
|
|
this driver does not work try the CS4232 driver.
|
|
|
|
config SOUND_CS4281
|
|
tristate "Crystal Sound CS4281"
|
|
depends on SOUND_PRIME!=n && SOUND
|
|
help
|
|
Picture and feature list at
|
|
<http://www.pcbroker.com/crystal4281.html>.
|
|
|
|
config SOUND_BCM_CS4297A
|
|
tristate "Crystal Sound CS4297a (for Swarm)"
|
|
depends on SOUND_PRIME!=n && SIBYTE_SWARM && SOUND
|
|
help
|
|
The BCM91250A has a Crystal CS4297a on synchronous serial
|
|
port B (in addition to the DB-9 serial port). Say Y or M
|
|
here to enable the sound chip instead of the UART. Also
|
|
note that CONFIG_KGDB should not be enabled at the same
|
|
time, since it also attempts to use this UART port.
|
|
|
|
config SOUND_ES1370
|
|
tristate "Ensoniq AudioPCI (ES1370)"
|
|
depends on SOUND_PRIME!=n && SOUND && PCI && SOUND_GAMEPORT
|
|
help
|
|
Say Y or M if you have a PCI sound card utilizing the Ensoniq
|
|
ES1370 chipset, such as Ensoniq's AudioPCI (non-97). To find
|
|
out if your sound card uses an ES1370 without removing your
|
|
computer's cover, use lspci -n and look for the PCI ID
|
|
1274:5000. Since Ensoniq was bought by Creative Labs,
|
|
Sound Blaster 64/PCI models are either ES1370 or ES1371 based.
|
|
This driver differs slightly from OSS/Free, so PLEASE READ
|
|
<file:Documentation/sound/oss/es1370>.
|
|
|
|
config SOUND_ES1371
|
|
tristate "Creative Ensoniq AudioPCI 97 (ES1371)"
|
|
depends on SOUND_PRIME!=n && SOUND && PCI && SOUND_GAMEPORT
|
|
help
|
|
Say Y or M if you have a PCI sound card utilizing the Ensoniq
|
|
ES1371 chipset, such as Ensoniq's AudioPCI97. To find out if
|
|
your sound card uses an ES1371 without removing your computer's
|
|
cover, use lspci -n and look for the PCI ID 1274:1371. Since
|
|
Ensoniq was bought by Creative Labs, Sound Blaster 64/PCI
|
|
models are either ES1370 or ES1371 based. This driver differs
|
|
slightly from OSS/Free, so PLEASE READ
|
|
<file:Documentation/sound/oss/es1371>.
|
|
|
|
config SOUND_ESSSOLO1
|
|
tristate "ESS Technology Solo1"
|
|
depends on SOUND_PRIME!=n && SOUND && SOUND_GAMEPORT && PCI
|
|
help
|
|
Say Y or M if you have a PCI sound card utilizing the ESS Technology
|
|
Solo1 chip. To find out if your sound card uses a
|
|
Solo1 chip without removing your computer's cover, use
|
|
lspci -n and look for the PCI ID 125D:1969. This driver
|
|
differs slightly from OSS/Free, so PLEASE READ
|
|
<file:Documentation/sound/oss/solo1>.
|
|
|
|
config SOUND_MAESTRO
|
|
tristate "ESS Maestro, Maestro2, Maestro2E driver"
|
|
depends on SOUND_PRIME!=n && SOUND && PCI
|
|
help
|
|
Say Y or M if you have a sound system driven by ESS's Maestro line
|
|
of PCI sound chips. These include the Maestro 1, Maestro 2, and
|
|
Maestro 2E. See <file:Documentation/sound/oss/Maestro> for more
|
|
details.
|
|
|
|
config SOUND_MAESTRO3
|
|
tristate "ESS Maestro3/Allegro driver (EXPERIMENTAL)"
|
|
depends on SOUND_PRIME!=n && SOUND && PCI && EXPERIMENTAL
|
|
help
|
|
Say Y or M if you have a sound system driven by ESS's Maestro 3
|
|
PCI sound chip.
|
|
|
|
config SOUND_ICH
|
|
tristate "Intel ICH (i8xx) audio support"
|
|
depends on SOUND_PRIME!=n && PCI
|
|
help
|
|
Support for integral audio in Intel's I/O Controller Hub (ICH)
|
|
chipset, as used on the 810/820/840 motherboards.
|
|
|
|
config SOUND_HARMONY
|
|
tristate "PA Harmony audio driver"
|
|
depends on GSC_LASI && SOUND_PRIME!=n
|
|
help
|
|
Say 'Y' or 'M' to include support for Harmony soundchip
|
|
on HP 712, 715/new and many other GSC based machines.
|
|
|
|
config SOUND_SONICVIBES
|
|
tristate "S3 SonicVibes"
|
|
depends on SOUND_PRIME!=n && SOUND && SOUND_GAMEPORT
|
|
help
|
|
Say Y or M if you have a PCI sound card utilizing the S3
|
|
SonicVibes chipset. To find out if your sound card uses a
|
|
SonicVibes chip without removing your computer's cover, use
|
|
lspci -n and look for the PCI ID 5333:CA00. This driver
|
|
differs slightly from OSS/Free, so PLEASE READ
|
|
<file:Documentation/sound/oss/sonicvibes>.
|
|
|
|
config SOUND_VWSND
|
|
tristate "SGI Visual Workstation Sound"
|
|
depends on SOUND_PRIME!=n && X86_VISWS && SOUND
|
|
help
|
|
Say Y or M if you have an SGI Visual Workstation and you want to be
|
|
able to use its on-board audio. Read
|
|
<file:Documentation/sound/oss/vwsnd> for more info on this driver's
|
|
capabilities.
|
|
|
|
config SOUND_HAL2
|
|
tristate "SGI HAL2 sound (EXPERIMENTAL)"
|
|
depends on SOUND_PRIME!=n && SOUND && SGI_IP22 && EXPERIMENTAL
|
|
help
|
|
Say Y or M if you have an SGI Indy system and want to be able to
|
|
use it's on-board A2 audio system.
|
|
|
|
config SOUND_IT8172
|
|
tristate "IT8172G Sound"
|
|
depends on SOUND_PRIME!=n && (MIPS_ITE8172 || MIPS_IVR) && SOUND
|
|
|
|
config SOUND_VRC5477
|
|
tristate "NEC Vrc5477 AC97 sound"
|
|
depends on SOUND_PRIME!=n && DDB5477 && SOUND
|
|
help
|
|
Say Y here to enable sound support for the NEC Vrc5477 chip, an
|
|
integrated, multi-function controller chip for MIPS CPUs. Works
|
|
with the AC97 codec.
|
|
|
|
config SOUND_AU1000
|
|
tristate "Au1000 Sound"
|
|
depends on SOUND_PRIME!=n && (SOC_AU1000 || SOC_AU1100 || SOC_AU1500) && SOUND
|
|
|
|
config SOUND_AU1550_AC97
|
|
tristate "Au1550 AC97 Sound"
|
|
depends on SOUND_PRIME!=n && SOC_AU1550 && SOUND
|
|
|
|
config SOUND_TRIDENT
|
|
tristate "Trident 4DWave DX/NX, SiS 7018 or ALi 5451 PCI Audio Core"
|
|
depends on SOUND_PRIME!=n && SOUND && SOUND_GAMEPORT
|
|
---help---
|
|
Say Y or M if you have a PCI sound card utilizing the Trident
|
|
4DWave-DX/NX chipset or your mother board chipset has SiS 7018
|
|
or ALi 5451 built-in. The SiS 7018 PCI Audio Core is embedded
|
|
in SiS960 Super South Bridge and SiS540/630 Single Chipset.
|
|
The ALi 5451 PCI Audio Core is embedded in ALi M1535, M1535D,
|
|
M1535+ or M1535D+ South Bridge.
|
|
|
|
Use lspci -n to find out if your sound card or chipset uses
|
|
Trident 4DWave or SiS 7018. PCI ID 1023:2000 or 1023:2001 stands
|
|
for Trident 4Dwave. PCI ID 1039:7018 stands for SiS7018. PCI ID
|
|
10B9:5451 stands for ALi5451.
|
|
|
|
This driver supports S/PDIF in/out (record/playback) for ALi 5451
|
|
embedded in ALi M1535+ and M1535D+. Note that they aren't all
|
|
enabled by default; you can enable them by saying Y to "/proc file
|
|
system support" and "Sysctl support", and after the /proc file
|
|
system has been mounted, executing the command
|
|
|
|
command what is enabled
|
|
|
|
echo 0>/proc/ALi5451 pcm out is also set to S/PDIF out. (Default).
|
|
|
|
echo 1>/proc/ALi5451 use S/PDIF out to output pcm data.
|
|
|
|
echo 2>/proc/ALi5451 use S/PDIF out to output non-pcm data.
|
|
(AC3...).
|
|
|
|
echo 3>/proc/ALi5451 record from Ac97 in(MIC, Line in...).
|
|
(Default).
|
|
|
|
echo 4>/proc/ALi5451 no matter Ac97 settings, record from S/PDIF
|
|
in.
|
|
|
|
|
|
This driver differs slightly from OSS/Free, so PLEASE READ the
|
|
comments at the top of <file:drivers/sound/trident.c>.
|
|
|
|
config SOUND_MSNDCLAS
|
|
tristate "Support for Turtle Beach MultiSound Classic, Tahiti, Monterey"
|
|
depends on SOUND_PRIME!=n && SOUND && (m || !STANDALONE)
|
|
help
|
|
Say M here if you have a Turtle Beach MultiSound Classic, Tahiti or
|
|
Monterey (not for the Pinnacle or Fiji).
|
|
|
|
See <file:Documentation/sound/oss/MultiSound> for important information
|
|
about this driver. Note that it has been discontinued, but the
|
|
Voyetra Turtle Beach knowledge base entry for it is still available
|
|
at <http://www.turtlebeach.com/site/kb_ftp/790.asp>.
|
|
|
|
comment "Compiled-in MSND Classic support requires firmware during compilation."
|
|
depends on SOUND_PRIME && SOUND_MSNDCLAS=y
|
|
|
|
config MSNDCLAS_HAVE_BOOT
|
|
bool
|
|
depends on SOUND_MSNDCLAS=y && !STANDALONE
|
|
default y
|
|
|
|
config MSNDCLAS_INIT_FILE
|
|
string "Full pathname of MSNDINIT.BIN firmware file"
|
|
depends on SOUND_MSNDCLAS
|
|
default "/etc/sound/msndinit.bin"
|
|
help
|
|
The MultiSound cards have two firmware files which are required for
|
|
operation, and are not currently included. These files can be
|
|
obtained from Turtle Beach. See
|
|
<file:Documentation/sound/oss/MultiSound> for information on how to
|
|
obtain this.
|
|
|
|
config MSNDCLAS_PERM_FILE
|
|
string "Full pathname of MSNDPERM.BIN firmware file"
|
|
depends on SOUND_MSNDCLAS
|
|
default "/etc/sound/msndperm.bin"
|
|
help
|
|
The MultiSound cards have two firmware files which are required for
|
|
operation, and are not currently included. These files can be
|
|
obtained from Turtle Beach. See
|
|
<file:Documentation/sound/oss/MultiSound> for information on how to
|
|
obtain this.
|
|
|
|
config MSNDCLAS_IRQ
|
|
int "MSND Classic IRQ 5, 7, 9, 10, 11, 12"
|
|
depends on SOUND_MSNDCLAS=y
|
|
default "5"
|
|
help
|
|
Interrupt Request line for the MultiSound Classic and related cards.
|
|
|
|
config MSNDCLAS_MEM
|
|
hex "MSND Classic memory B0000, C8000, D0000, D8000, E0000, E8000"
|
|
depends on SOUND_MSNDCLAS=y
|
|
default "D0000"
|
|
help
|
|
Memory-mapped I/O base address for the MultiSound Classic and
|
|
related cards.
|
|
|
|
config MSNDCLAS_IO
|
|
hex "MSND Classic I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
|
|
depends on SOUND_MSNDCLAS=y
|
|
default "290"
|
|
help
|
|
I/O port address for the MultiSound Classic and related cards.
|
|
|
|
config SOUND_MSNDPIN
|
|
tristate "Support for Turtle Beach MultiSound Pinnacle, Fiji"
|
|
depends on SOUND_PRIME!=n && SOUND && (m || !STANDALONE)
|
|
help
|
|
Say M here if you have a Turtle Beach MultiSound Pinnacle or Fiji.
|
|
See <file:Documentation/sound/oss/MultiSound> for important information
|
|
about this driver. Note that it has been discontinued, but the
|
|
Voyetra Turtle Beach knowledge base entry for it is still available
|
|
at <http://www.turtlebeach.com/site/kb_ftp/600.asp>.
|
|
|
|
comment "Compiled-in MSND Pinnacle support requires firmware during compilation."
|
|
depends on SOUND_PRIME && SOUND_MSNDPIN=y
|
|
|
|
config MSNDPIN_HAVE_BOOT
|
|
bool
|
|
depends on SOUND_MSNDPIN=y
|
|
default y
|
|
|
|
config MSNDPIN_INIT_FILE
|
|
string "Full pathname of PNDSPINI.BIN firmware file"
|
|
depends on SOUND_MSNDPIN
|
|
default "/etc/sound/pndspini.bin"
|
|
help
|
|
The MultiSound cards have two firmware files which are required
|
|
for operation, and are not currently included. These files can be
|
|
obtained from Turtle Beach. See
|
|
<file:Documentation/sound/oss/MultiSound> for information on how to
|
|
obtain this.
|
|
|
|
config MSNDPIN_PERM_FILE
|
|
string "Full pathname of PNDSPERM.BIN firmware file"
|
|
depends on SOUND_MSNDPIN
|
|
default "/etc/sound/pndsperm.bin"
|
|
help
|
|
The MultiSound cards have two firmware files which are required for
|
|
operation, and are not currently included. These files can be
|
|
obtained from Turtle Beach. See
|
|
<file:Documentation/sound/oss/MultiSound> for information on how to
|
|
obtain this.
|
|
|
|
config MSNDPIN_IRQ
|
|
int "MSND Pinnacle IRQ 5, 7, 9, 10, 11, 12"
|
|
depends on SOUND_MSNDPIN=y
|
|
default "5"
|
|
help
|
|
Interrupt request line for the primary synthesizer on MultiSound
|
|
Pinnacle and Fiji sound cards.
|
|
|
|
config MSNDPIN_MEM
|
|
hex "MSND Pinnacle memory B0000, C8000, D0000, D8000, E0000, E8000"
|
|
depends on SOUND_MSNDPIN=y
|
|
default "D0000"
|
|
help
|
|
Memory-mapped I/O base address for the primary synthesizer on
|
|
MultiSound Pinnacle and Fiji sound cards.
|
|
|
|
config MSNDPIN_IO
|
|
hex "MSND Pinnacle I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
|
|
depends on SOUND_MSNDPIN=y
|
|
default "290"
|
|
help
|
|
Memory-mapped I/O base address for the primary synthesizer on
|
|
MultiSound Pinnacle and Fiji sound cards.
|
|
|
|
config MSNDPIN_DIGITAL
|
|
bool "MSND Pinnacle has S/PDIF I/O"
|
|
depends on SOUND_MSNDPIN=y
|
|
help
|
|
If you have the S/PDIF daughter board for the Pinnacle or Fiji,
|
|
answer Y here; otherwise, say N. If you have this, you will be able
|
|
to play and record from the S/PDIF port (digital signal). See
|
|
<file:Documentation/sound/oss/MultiSound> for information on how to make
|
|
use of this capability.
|
|
|
|
config MSNDPIN_NONPNP
|
|
bool "MSND Pinnacle non-PnP Mode"
|
|
depends on SOUND_MSNDPIN=y
|
|
help
|
|
The Pinnacle and Fiji card resources can be configured either with
|
|
PnP, or through a configuration port. Say Y here if your card is NOT
|
|
in PnP mode. For the Pinnacle, configuration in non-PnP mode allows
|
|
use of the IDE and joystick peripherals on the card as well; these
|
|
do not show up when the card is in PnP mode. Specifying zero for any
|
|
resource of a device will disable the device. If you are running the
|
|
card in PnP mode, you must say N here and use isapnptools to
|
|
configure the card's resources.
|
|
|
|
comment "MSND Pinnacle DSP section will be configured to above parameters."
|
|
depends on SOUND_PRIME && SOUND_MSNDPIN=y && MSNDPIN_NONPNP
|
|
|
|
config MSNDPIN_CFG
|
|
hex "MSND Pinnacle config port 250,260,270"
|
|
depends on MSNDPIN_NONPNP
|
|
default "250"
|
|
help
|
|
This is the port which the Pinnacle and Fiji uses to configure the
|
|
card's resources when not in PnP mode. If your card is in PnP mode,
|
|
then be sure to say N to the previous option, "MSND Pinnacle Non-PnP
|
|
Mode".
|
|
|
|
comment "Pinnacle-specific Device Configuration (0 disables)"
|
|
depends on SOUND_PRIME && SOUND_MSNDPIN=y && MSNDPIN_NONPNP
|
|
|
|
config MSNDPIN_MPU_IO
|
|
hex "MSND Pinnacle MPU I/O (e.g. 330)"
|
|
depends on MSNDPIN_NONPNP
|
|
default "0"
|
|
help
|
|
Memory-mapped I/O base address for the Kurzweil daughterboard
|
|
synthesizer on MultiSound Pinnacle and Fiji sound cards.
|
|
|
|
config MSNDPIN_MPU_IRQ
|
|
int "MSND Pinnacle MPU IRQ (e.g. 9)"
|
|
depends on MSNDPIN_NONPNP
|
|
default "0"
|
|
help
|
|
Interrupt request number for the Kurzweil daughterboard
|
|
synthesizer on MultiSound Pinnacle and Fiji sound cards.
|
|
|
|
config MSNDPIN_IDE_IO0
|
|
hex "MSND Pinnacle IDE I/O 0 (e.g. 170)"
|
|
depends on MSNDPIN_NONPNP
|
|
default "0"
|
|
help
|
|
CD-ROM drive 0 memory-mapped I/O base address for the MultiSound
|
|
Pinnacle and Fiji sound cards.
|
|
|
|
config MSNDPIN_IDE_IO1
|
|
hex "MSND Pinnacle IDE I/O 1 (e.g. 376)"
|
|
depends on MSNDPIN_NONPNP
|
|
default "0"
|
|
help
|
|
CD-ROM drive 1 memory-mapped I/O base address for the MultiSound
|
|
Pinnacle and Fiji sound cards.
|
|
|
|
config MSNDPIN_IDE_IRQ
|
|
int "MSND Pinnacle IDE IRQ (e.g. 15)"
|
|
depends on MSNDPIN_NONPNP
|
|
default "0"
|
|
help
|
|
Interrupt request number for the IDE CD-ROM interface on the
|
|
MultiSound Pinnacle and Fiji sound cards.
|
|
|
|
config MSNDPIN_JOYSTICK_IO
|
|
hex "MSND Pinnacle joystick I/O (e.g. 200)"
|
|
depends on MSNDPIN_NONPNP
|
|
default "0"
|
|
help
|
|
Memory-mapped I/O base address for the joystick port on MultiSound
|
|
Pinnacle and Fiji sound cards.
|
|
|
|
config MSND_FIFOSIZE
|
|
int "MSND buffer size (kB)"
|
|
depends on SOUND_PRIME && (SOUND_MSNDPIN=y || SOUND_MSNDCLAS=y)
|
|
default "128"
|
|
help
|
|
Configures the size of each audio buffer, in kilobytes, for
|
|
recording and playing in the MultiSound drivers (both the Classic
|
|
and Pinnacle). Larger values reduce the chance of data overruns at
|
|
the expense of overall latency. If unsure, use the default.
|
|
|
|
config SOUND_VIA82CXXX
|
|
tristate "VIA 82C686 Audio Codec"
|
|
depends on SOUND_PRIME!=n && PCI
|
|
help
|
|
Say Y here to include support for the audio codec found on VIA
|
|
82Cxxx-based chips. Typically these are built into a motherboard.
|
|
|
|
DO NOT select Sound Blaster or Adlib with this driver, unless
|
|
you have a Sound Blaster or Adlib card in addition to your VIA
|
|
audio chip.
|
|
|
|
config MIDI_VIA82CXXX
|
|
bool "VIA 82C686 MIDI"
|
|
depends on SOUND_VIA82CXXX
|
|
help
|
|
Answer Y to use the MIDI interface of the Via686. You may need to
|
|
enable this in the BIOS before it will work. This is for connection
|
|
to external MIDI hardware, and is not required for software playback
|
|
of MIDI files.
|
|
|
|
config SOUND_OSS
|
|
tristate "OSS sound modules"
|
|
depends on SOUND_PRIME!=n && SOUND
|
|
help
|
|
OSS is the Open Sound System suite of sound card drivers. They make
|
|
sound programming easier since they provide a common API. Say Y or
|
|
M here (the module will be called sound) if you haven't found a
|
|
driver for your sound card above, then pick your driver from the
|
|
list below.
|
|
|
|
config SOUND_TRACEINIT
|
|
bool "Verbose initialisation"
|
|
depends on SOUND_OSS
|
|
help
|
|
Verbose soundcard initialization -- affects the format of autoprobe
|
|
and initialization messages at boot time.
|
|
|
|
config SOUND_DMAP
|
|
bool "Persistent DMA buffers"
|
|
depends on SOUND_OSS
|
|
---help---
|
|
Linux can often have problems allocating DMA buffers for ISA sound
|
|
cards on machines with more than 16MB of RAM. This is because ISA
|
|
DMA buffers must exist below the 16MB boundary and it is quite
|
|
possible that a large enough free block in this region cannot be
|
|
found after the machine has been running for a while. If you say Y
|
|
here the DMA buffers (64Kb) will be allocated at boot time and kept
|
|
until the shutdown. This option is only useful if you said Y to
|
|
"OSS sound modules", above. If you said M to "OSS sound modules"
|
|
then you can get the persistent DMA buffer functionality by passing
|
|
the command-line argument "dmabuf=1" to the sound module.
|
|
|
|
Say Y unless you have 16MB or more RAM or a PCI sound card.
|
|
|
|
config SOUND_AD1816
|
|
tristate "AD1816(A) based cards (EXPERIMENTAL)"
|
|
depends on EXPERIMENTAL && SOUND_OSS
|
|
help
|
|
Say M here if you have a sound card based on the Analog Devices
|
|
AD1816(A) chip.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"ad1816=<io>,<irq>,<dma>,<dma2>" to the kernel command line.
|
|
|
|
config SOUND_AD1889
|
|
tristate "AD1889 based cards (AD1819 codec) (EXPERIMENTAL)"
|
|
depends on EXPERIMENTAL && SOUND_OSS
|
|
help
|
|
Say M here if you have a sound card based on the Analog Devices
|
|
AD1889 chip.
|
|
|
|
config SOUND_SGALAXY
|
|
tristate "Aztech Sound Galaxy (non-PnP) cards"
|
|
depends on SOUND_OSS
|
|
help
|
|
This module initializes the older non Plug and Play sound galaxy
|
|
cards from Aztech. It supports the Waverider Pro 32 - 3D and the
|
|
Galaxy Washington 16.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"sgalaxy=<io>,<irq>,<dma>,<dma2>,<sgbase>" to the kernel command
|
|
line.
|
|
|
|
config SOUND_ADLIB
|
|
tristate "Adlib Cards"
|
|
depends on SOUND_OSS
|
|
help
|
|
Includes ASB 64 4D. Information on programming AdLib cards is
|
|
available at <http://www.itsnet.com/home/ldragon/Specs/adlib.html>.
|
|
|
|
config SOUND_ACI_MIXER
|
|
tristate "ACI mixer (miroSOUND PCM1-pro/PCM12/PCM20)"
|
|
depends on SOUND_OSS
|
|
---help---
|
|
ACI (Audio Command Interface) is a protocol used to communicate with
|
|
the microcontroller on some sound cards produced by miro and
|
|
Cardinal Technologies. The main function of the ACI is to control
|
|
the mixer and to get a product identification.
|
|
|
|
This VoxWare ACI driver currently supports the ACI functions on the
|
|
miroSOUND PCM1-pro, PCM12 and PCM20 radio. On the PCM20 radio, ACI
|
|
also controls the radio tuner. This is supported in the video4linux
|
|
miropcm20 driver (say M or Y here and go back to "Multimedia
|
|
devices" -> "Radio Adapters").
|
|
|
|
This driver is also available as a module and will be called aci.
|
|
|
|
config SOUND_CS4232
|
|
tristate "Crystal CS4232 based (PnP) cards"
|
|
depends on SOUND_OSS
|
|
help
|
|
Say Y here if you have a card based on the Crystal CS4232 chip set,
|
|
which uses its own Plug and Play protocol.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"cs4232=<io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>" to the kernel
|
|
command line.
|
|
|
|
See <file:Documentation/sound/oss/CS4232> for more information on
|
|
configuring this card.
|
|
|
|
config SOUND_SSCAPE
|
|
tristate "Ensoniq SoundScape support"
|
|
depends on SOUND_OSS
|
|
help
|
|
Answer Y if you have a sound card based on the Ensoniq SoundScape
|
|
chipset. Such cards are being manufactured at least by Ensoniq, Spea
|
|
and Reveal (Reveal makes also other cards).
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"sscape=<io>,<irq>,<dma>,<mpuio>,<mpuirq>" to the kernel command
|
|
line.
|
|
|
|
config SOUND_GUS
|
|
tristate "Gravis Ultrasound support"
|
|
depends on SOUND_OSS
|
|
help
|
|
Say Y here for any type of Gravis Ultrasound card, including the GUS
|
|
or GUS MAX. See also <file:Documentation/sound/oss/ultrasound> for more
|
|
information on configuring this card with modules.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"gus=<io>,<irq>,<dma>,<dma2>" to the kernel command line.
|
|
|
|
config SOUND_GUS16
|
|
bool "16 bit sampling option of GUS (_NOT_ GUS MAX)"
|
|
depends on SOUND_GUS
|
|
help
|
|
Support for Gravis Ulstrasound (GUS) cards (other than the GUS),
|
|
sampling at 16-bit width.
|
|
|
|
config SOUND_GUSMAX
|
|
bool "GUS MAX support"
|
|
depends on SOUND_GUS
|
|
help
|
|
Support for Gravis Ulstrasound MAX.
|
|
|
|
config SOUND_VMIDI
|
|
tristate "Loopback MIDI device support"
|
|
depends on SOUND_OSS
|
|
help
|
|
Support for MIDI loopback on port 1 or 2.
|
|
|
|
config SOUND_TRIX
|
|
tristate "MediaTrix AudioTrix Pro support"
|
|
depends on SOUND_OSS
|
|
help
|
|
Answer Y if you have the AudioTriX Pro sound card manufactured
|
|
by MediaTrix.
|
|
|
|
config TRIX_HAVE_BOOT
|
|
bool "Have TRXPRO.HEX firmware file"
|
|
depends on SOUND_TRIX=y && !STANDALONE
|
|
help
|
|
The MediaTrix AudioTrix Pro has an on-board microcontroller which
|
|
needs to be initialized by downloading the code from the file
|
|
TRXPRO.HEX in the DOS driver directory. If you don't have the
|
|
TRXPRO.HEX file handy you may skip this step. However, the SB and
|
|
MPU-401 modes of AudioTrix Pro will not work without this file!
|
|
|
|
config TRIX_BOOT_FILE
|
|
string "Full pathname of TRXPRO.HEX firmware file"
|
|
depends on TRIX_HAVE_BOOT
|
|
default "/etc/sound/trxpro.hex"
|
|
help
|
|
Enter the full pathname of your TRXPRO.HEX file, starting from /.
|
|
|
|
config SOUND_MSS
|
|
tristate "Microsoft Sound System support"
|
|
depends on SOUND_OSS
|
|
---help---
|
|
Again think carefully before answering Y to this question. It's
|
|
safe to answer Y if you have the original Windows Sound System card
|
|
made by Microsoft or Aztech SG 16 Pro (or NX16 Pro). Also you may
|
|
say Y in case your card is NOT among these:
|
|
|
|
ATI Stereo F/X, AdLib, Audio Excell DSP16, Cardinal DSP16,
|
|
Ensoniq SoundScape (and compatibles made by Reveal and Spea),
|
|
Gravis Ultrasound, Gravis Ultrasound ACE, Gravis Ultrasound Max,
|
|
Gravis Ultrasound with 16 bit option, Logitech Sound Man 16,
|
|
Logitech SoundMan Games, Logitech SoundMan Wave, MAD16 Pro (OPTi
|
|
82C929), Media Vision Jazz16, MediaTriX AudioTriX Pro, Microsoft
|
|
Windows Sound System (MSS/WSS), Mozart (OAK OTI-601), Orchid
|
|
SW32, Personal Sound System (PSS), Pro Audio Spectrum 16, Pro
|
|
Audio Studio 16, Pro Sonic 16, Roland MPU-401 MIDI interface,
|
|
Sound Blaster 1.0, Sound Blaster 16, Sound Blaster 16ASP, Sound
|
|
Blaster 2.0, Sound Blaster AWE32, Sound Blaster Pro, TI TM4000M
|
|
notebook, ThunderBoard, Turtle Beach Tropez, Yamaha FM
|
|
synthesizers (OPL2, OPL3 and OPL4), 6850 UART MIDI Interface.
|
|
|
|
For cards having native support in VoxWare, consult the card
|
|
specific instructions in <file:Documentation/sound/oss/README.OSS>.
|
|
Some drivers have their own MSS support and saying Y to this option
|
|
will cause a conflict.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"ad1848=<io>,<irq>,<dma>,<dma2>[,<type>]" to the kernel command
|
|
line.
|
|
|
|
config SOUND_MPU401
|
|
tristate "MPU-401 support (NOT for SB16)"
|
|
depends on SOUND_OSS
|
|
---help---
|
|
Be careful with this question. The MPU401 interface is supported by
|
|
all sound cards. However, some natively supported cards have their
|
|
own driver for MPU401. Enabling this MPU401 option with these cards
|
|
will cause a conflict. Also, enabling MPU401 on a system that
|
|
doesn't really have a MPU401 could cause some trouble. If your card
|
|
was in the list of supported cards, look at the card specific
|
|
instructions in the <file:Documentation/sound/oss/README.OSS> file. It
|
|
is safe to answer Y if you have a true MPU401 MIDI interface card.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"mpu401=<io>,<irq>" to the kernel command line.
|
|
|
|
config SOUND_NM256
|
|
tristate "NM256AV/NM256ZX audio support"
|
|
depends on SOUND_OSS
|
|
help
|
|
Say M here to include audio support for the NeoMagic 256AV/256ZX
|
|
chipsets. These are the audio chipsets found in the Sony
|
|
Z505S/SX/DX, some Sony F-series, and the Dell Latitude CPi and CPt
|
|
laptops. It includes support for an AC97-compatible mixer and an
|
|
apparently proprietary sound engine.
|
|
|
|
See <file:Documentation/sound/oss/NM256> for further information.
|
|
|
|
config SOUND_MAD16
|
|
tristate "OPTi MAD16 and/or Mozart based cards"
|
|
depends on SOUND_OSS && SOUND_GAMEPORT
|
|
---help---
|
|
Answer Y if your card has a Mozart (OAK OTI-601) or MAD16 (OPTi
|
|
82C928 or 82C929 or 82C931) audio interface chip. These chips are
|
|
quite common so it's possible that many no-name cards have one of
|
|
them. In addition the MAD16 chip is used in some cards made by known
|
|
manufacturers such as Turtle Beach (Tropez), Reveal (some models)
|
|
and Diamond (latest ones). Note however that the Tropez sound cards
|
|
have their own driver; if you have one of those, say N here and Y or
|
|
M to "Full support for Turtle Beach WaveFront", below.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"mad16=<io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>" to the
|
|
kernel command line.
|
|
|
|
See also <file:Documentation/sound/oss/Opti> and
|
|
<file:Documentation/sound/oss/MAD16> for more information on setting
|
|
these cards up as modules.
|
|
|
|
config MAD16_OLDCARD
|
|
bool "Support MIDI in older MAD16 based cards (requires SB)"
|
|
depends on SOUND_MAD16
|
|
help
|
|
Answer Y (or M) if you have an older card based on the C928 or
|
|
Mozart chipset and you want to have MIDI support. If you enable this
|
|
option you also need to enable support for Sound Blaster.
|
|
|
|
config SOUND_PAS
|
|
tristate "ProAudioSpectrum 16 support"
|
|
depends on SOUND_OSS
|
|
---help---
|
|
Answer Y only if you have a Pro Audio Spectrum 16, ProAudio Studio
|
|
16 or Logitech SoundMan 16 sound card. Answer N if you have some
|
|
other card made by Media Vision or Logitech since those are not
|
|
PAS16 compatible. Please read <file:Documentation/sound/oss/PAS16>.
|
|
It is not necessary to add Sound Blaster support separately; it
|
|
is included in PAS support.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"pas2=<io>,<irq>,<dma>,<dma2>,<sbio>,<sbirq>,<sbdma>,<sbdma2>
|
|
to the kernel command line.
|
|
|
|
config PAS_JOYSTICK
|
|
bool "Enable PAS16 joystick port"
|
|
depends on SOUND_PAS=y
|
|
help
|
|
Say Y here to enable the Pro Audio Spectrum 16's auxiliary joystick
|
|
port.
|
|
|
|
config SOUND_PSS
|
|
tristate "PSS (AD1848, ADSP-2115, ESC614) support"
|
|
depends on SOUND_OSS
|
|
help
|
|
Answer Y or M if you have an Orchid SW32, Cardinal DSP16, Beethoven
|
|
ADSP-16 or some other card based on the PSS chipset (AD1848 codec +
|
|
ADSP-2115 DSP chip + Echo ESC614 ASIC CHIP). For more information on
|
|
how to compile it into the kernel or as a module see the file
|
|
<file:Documentation/sound/oss/PSS>.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"pss=<io>,<mssio>,<mssirq>,<mssdma>,<mpuio>,<mpuirq>" to the kernel
|
|
command line.
|
|
|
|
config PSS_MIXER
|
|
bool "Enable PSS mixer (Beethoven ADSP-16 and other compatibile)"
|
|
depends on SOUND_PSS
|
|
help
|
|
Answer Y for Beethoven ADSP-16. You may try to say Y also for other
|
|
cards if they have master volume, bass, treble, and you can't
|
|
control it under Linux. If you answer N for Beethoven ADSP-16, you
|
|
can't control master volume, bass, treble and synth volume.
|
|
|
|
If you said M to "PSS support" above, you may enable or disable this
|
|
PSS mixer with the module parameter pss_mixer. For more information
|
|
see the file <file:Documentation/sound/oss/PSS>.
|
|
|
|
config PSS_HAVE_BOOT
|
|
bool "Have DSPxxx.LD firmware file"
|
|
depends on SOUND_PSS && !STANDALONE
|
|
help
|
|
If you have the DSPxxx.LD file or SYNTH.LD file for you card, say Y
|
|
to include this file. Without this file the synth device (OPL) may
|
|
not work.
|
|
|
|
config PSS_BOOT_FILE
|
|
string "Full pathname of DSPxxx.LD firmware file"
|
|
depends on PSS_HAVE_BOOT
|
|
default "/etc/sound/dsp001.ld"
|
|
help
|
|
Enter the full pathname of your DSPxxx.LD file or SYNTH.LD file,
|
|
starting from /.
|
|
|
|
config SOUND_SB
|
|
tristate "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
|
|
depends on SOUND_OSS
|
|
---help---
|
|
Answer Y if you have an original Sound Blaster card made by Creative
|
|
Labs or a 100% hardware compatible clone (like the Thunderboard or
|
|
SM Games). For an unknown card you may answer Y if the card claims
|
|
to be Sound Blaster-compatible.
|
|
|
|
Please read the file <file:Documentation/sound/oss/Soundblaster>.
|
|
|
|
You should also say Y here for cards based on the Avance Logic
|
|
ALS-007 and ALS-1X0 chips (read <file:Documentation/sound/oss/ALS>) and
|
|
for cards based on ESS chips (read
|
|
<file:Documentation/sound/oss/ESS1868> and
|
|
<file:Documentation/sound/oss/ESS>). If you have an SB AWE 32 or SB AWE
|
|
64, say Y here and also to "AWE32 synth" below and read
|
|
<file:Documentation/sound/oss/INSTALL.awe>. If you have an IBM Mwave
|
|
card, say Y here and read <file:Documentation/sound/oss/mwave>.
|
|
|
|
If you compile the driver into the kernel and don't want to use
|
|
isapnp, you have to add "sb=<io>,<irq>,<dma>,<dma2>" to the kernel
|
|
command line.
|
|
|
|
You can say M here to compile this driver as a module; the module is
|
|
called sb.
|
|
|
|
config SOUND_AWE32_SYNTH
|
|
tristate "AWE32 synth"
|
|
depends on SOUND_OSS
|
|
help
|
|
Say Y here if you have a Sound Blaster SB32, AWE32-PnP, SB AWE64 or
|
|
similar sound card. See <file:Documentation/sound/oss/README.awe>,
|
|
<file:Documentation/sound/oss/AWE32> and the Soundblaster-AWE
|
|
mini-HOWTO, available from <http://www.tldp.org/docs.html#howto>
|
|
for more info.
|
|
|
|
config SOUND_WAVEFRONT
|
|
tristate "Full support for Turtle Beach WaveFront (Tropez Plus, Tropez, Maui) synth/soundcards"
|
|
depends on SOUND_OSS && m
|
|
help
|
|
Answer Y or M if you have a Tropez Plus, Tropez or Maui sound card
|
|
and read the files <file:Documentation/sound/oss/Wavefront> and
|
|
<file:Documentation/sound/oss/Tropez+>.
|
|
|
|
config SOUND_MAUI
|
|
tristate "Limited support for Turtle Beach Wave Front (Maui, Tropez) synthesizers"
|
|
depends on SOUND_OSS
|
|
help
|
|
Say Y here if you have a Turtle Beach Wave Front, Maui, or Tropez
|
|
sound card.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"maui=<io>,<irq>" to the kernel command line.
|
|
|
|
config MAUI_HAVE_BOOT
|
|
bool "Have OSWF.MOT firmware file"
|
|
depends on SOUND_MAUI=y && !STANDALONE
|
|
help
|
|
Turtle Beach Maui and Tropez sound cards have a microcontroller
|
|
which needs to be initialized prior to use. OSWF.MOT is a file
|
|
distributed with the card's DOS/Windows drivers. Answer Y if you
|
|
have this file.
|
|
|
|
config MAUI_BOOT_FILE
|
|
string "Full pathname of OSWF.MOT firmware file"
|
|
depends on MAUI_HAVE_BOOT
|
|
default "/etc/sound/oswf.mot"
|
|
help
|
|
Enter the full pathname of your OSWF.MOT file, starting from /.
|
|
|
|
config SOUND_YM3812
|
|
tristate "Yamaha FM synthesizer (YM3812/OPL-3) support"
|
|
depends on SOUND_OSS
|
|
---help---
|
|
Answer Y if your card has a FM chip made by Yamaha (OPL2/OPL3/OPL4).
|
|
Answering Y is usually a safe and recommended choice, however some
|
|
cards may have software (TSR) FM emulation. Enabling FM support with
|
|
these cards may cause trouble (I don't currently know of any such
|
|
cards, however). Please read the file
|
|
<file:Documentation/sound/oss/OPL3> if your card has an OPL3 chip.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"opl3=<io>" to the kernel command line.
|
|
|
|
If unsure, say Y.
|
|
|
|
config SOUND_OPL3SA1
|
|
tristate "Yamaha OPL3-SA1 audio controller"
|
|
depends on SOUND_OSS
|
|
help
|
|
Say Y or M if you have a Yamaha OPL3-SA1 sound chip, which is
|
|
usually built into motherboards. Read
|
|
<file:Documentation/sound/oss/OPL3-SA> for details.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"opl3sa=<io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>" to the kernel
|
|
command line.
|
|
|
|
config SOUND_OPL3SA2
|
|
tristate "Yamaha OPL3-SA2 and SA3 based PnP cards"
|
|
depends on SOUND_OSS
|
|
help
|
|
Say Y or M if you have a card based on one of these Yamaha sound
|
|
chipsets or the "SAx", which is actually a SA3. Read
|
|
<file:Documentation/sound/oss/OPL3-SA2> for more information on
|
|
configuring these cards.
|
|
|
|
If you compile the driver into the kernel and do not also
|
|
configure in the optional ISA PnP support, you will have to add
|
|
"opl3sa2=<io>,<irq>,<dma>,<dma2>,<mssio>,<mpuio>" to the kernel
|
|
command line.
|
|
|
|
config SOUND_YMFPCI
|
|
tristate "Yamaha YMF7xx PCI audio (native mode)"
|
|
depends on SOUND_OSS && PCI
|
|
help
|
|
Support for Yamaha cards including the YMF711, YMF715, YMF718,
|
|
YMF719, YMF724, Waveforce 192XG, and Waveforce 192 Digital.
|
|
|
|
config SOUND_YMFPCI_LEGACY
|
|
bool "Yamaha PCI legacy ports support"
|
|
depends on SOUND_YMFPCI
|
|
help
|
|
Support for YMF7xx PCI cards emulating an MP401.
|
|
|
|
config SOUND_UART6850
|
|
tristate "6850 UART support"
|
|
depends on SOUND_OSS
|
|
help
|
|
This option enables support for MIDI interfaces based on the 6850
|
|
UART chip. This interface is rarely found on sound cards. It's safe
|
|
to answer N to this question.
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"uart6850=<io>,<irq>" to the kernel command line.
|
|
|
|
config SOUND_AEDSP16
|
|
tristate "Gallant Audio Cards (SC-6000 and SC-6600 based)"
|
|
depends on SOUND_OSS
|
|
---help---
|
|
Answer Y if you have a Gallant's Audio Excel DSP 16 card. This
|
|
driver supports Audio Excel DSP 16 but not the III nor PnP versions
|
|
of this card.
|
|
|
|
The Gallant's Audio Excel DSP 16 card can emulate either an SBPro or
|
|
a Microsoft Sound System card, so you should have said Y to either
|
|
"100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
|
|
or "Microsoft Sound System support", above, and you need to answer
|
|
the "MSS emulation" and "SBPro emulation" questions below
|
|
accordingly. You should say Y to one and only one of these two
|
|
questions.
|
|
|
|
Read the <file:Documentation/sound/oss/README.OSS> file and the head of
|
|
<file:drivers/sound/aedsp16.c> as well as
|
|
<file:Documentation/sound/oss/AudioExcelDSP16> to get more information
|
|
about this driver and its configuration.
|
|
|
|
config SC6600
|
|
bool "SC-6600 based audio cards (new Audio Excel DSP 16)"
|
|
depends on SOUND_AEDSP16
|
|
help
|
|
The SC6600 is the new version of DSP mounted on the Audio Excel DSP
|
|
16 cards. Find in the manual the FCC ID of your audio card and
|
|
answer Y if you have an SC6600 DSP.
|
|
|
|
config SC6600_JOY
|
|
bool "Activate SC-6600 Joystick Interface"
|
|
depends on SC6600
|
|
help
|
|
Say Y here in order to use the joystick interface of the Audio Excel
|
|
DSP 16 card.
|
|
|
|
config SC6600_CDROM
|
|
int "SC-6600 CDROM Interface (4=None, 3=IDE, 1=Panasonic, 0=?Sony?)"
|
|
depends on SC6600
|
|
default "4"
|
|
help
|
|
This is used to activate the CD-ROM interface of the Audio Excel
|
|
DSP 16 card. Enter: 0 for Sony, 1 for Panasonic, 2 for IDE, 4 for no
|
|
CD-ROM present.
|
|
|
|
config SC6600_CDROMBASE
|
|
hex "SC-6600 CDROM Interface I/O Address"
|
|
depends on SC6600
|
|
default "0"
|
|
help
|
|
Base I/O port address for the CD-ROM interface of the Audio Excel
|
|
DSP 16 card.
|
|
|
|
choice
|
|
prompt "Audio Excel DSP 16"
|
|
optional
|
|
depends on SOUND_AEDSP16
|
|
|
|
config AEDSP16_MSS
|
|
bool "MSS emulation"
|
|
depends on SOUND_MSS
|
|
help
|
|
Answer Y if you want your audio card to emulate Microsoft Sound
|
|
System. You should then say Y to "Microsoft Sound System support"
|
|
and say N to "Audio Excel DSP 16 (SBPro emulation)".
|
|
|
|
config AEDSP16_SBPRO
|
|
bool "SBPro emulation"
|
|
depends on SOUND_SB
|
|
help
|
|
Answer Y if you want your audio card to emulate Sound Blaster Pro.
|
|
You should then say Y to "100% Sound Blaster compatibles
|
|
(SB16/32/64, ESS, Jazz16) support" and N to "Audio Excel DSP 16 (MSS
|
|
emulation)".
|
|
|
|
If you compile the driver into the kernel, you have to add
|
|
"aedsp16=<io>,<irq>,<dma>,<mssio>,<mpuio>,<mouirq>" to the kernel
|
|
command line.
|
|
|
|
endchoice
|
|
|
|
config AEDSP16_MPU401
|
|
bool "Audio Excel DSP 16 (MPU401 emulation)"
|
|
depends on SOUND_AEDSP16 && SOUND_MPU401
|
|
help
|
|
Answer Y if you want your audio card to emulate the MPU-401 midi
|
|
interface. You should then also say Y to "MPU-401 support".
|
|
|
|
Note that the I/O base for MPU-401 support of aedsp16 is the same
|
|
you have selected for "MPU-401 support". If you are using this
|
|
driver as a module you have to specify the MPU I/O base address with
|
|
the parameter 'mpu_base=0xNNN'.
|
|
|
|
config SOUND_VIDC
|
|
tristate "VIDC 16-bit sound"
|
|
depends on ARM && (ARCH_ACORN || ARCH_CLPS7500) && SOUND_OSS
|
|
help
|
|
16-bit support for the VIDC onboard sound hardware found on Acorn
|
|
machines.
|
|
|
|
config SOUND_WAVEARTIST
|
|
tristate "Netwinder WaveArtist"
|
|
depends on ARM && SOUND_OSS && ARCH_NETWINDER
|
|
help
|
|
Say Y here to include support for the Rockwell WaveArtist sound
|
|
system. This driver is mainly for the NetWinder.
|
|
|
|
config SOUND_TVMIXER
|
|
tristate "TV card (bt848) mixer support"
|
|
depends on SOUND_PRIME!=n && SOUND && I2C
|
|
help
|
|
Support for audio mixer facilities on the BT848 TV frame-grabber
|
|
card.
|
|
|
|
config SOUND_KAHLUA
|
|
tristate "XpressAudio Sound Blaster emulation"
|
|
depends on SOUND_SB
|
|
|
|
config SOUND_ALI5455
|
|
tristate "ALi5455 audio support"
|
|
depends on SOUND_PRIME!=n && PCI
|
|
|
|
config SOUND_FORTE
|
|
tristate "ForteMedia FM801 driver"
|
|
depends on SOUND_PRIME!=n && PCI
|
|
help
|
|
Say Y or M if you want driver support for the ForteMedia FM801 PCI
|
|
audio controller (Abit AU10, Genius Sound Maker, HP Workstation
|
|
zx2000, and others).
|
|
|
|
config SOUND_RME96XX
|
|
tristate "RME Hammerfall (RME96XX) support"
|
|
depends on SOUND_PRIME!=n && PCI
|
|
help
|
|
Say Y or M if you have a Hammerfall or Hammerfall light
|
|
multichannel card from RME. If you want to access advanced
|
|
features of the card, read <file:Documentation/sound/oss/rme96xx>.
|
|
|
|
config SOUND_AD1980
|
|
tristate "AD1980 front/back switch plugin"
|
|
depends on SOUND_PRIME!=n
|
|
|
|
config SOUND_SH_DAC_AUDIO
|
|
tristate "SuperH DAC audio support"
|
|
depends on SOUND_PRIME!=n && SOUND && CPU_SH3
|
|
|
|
config SOUND_SH_DAC_AUDIO_CHANNEL
|
|
int " DAC channel"
|
|
default "1"
|
|
depends on SOUND_SH_DAC_AUDIO
|