forked from Minki/linux
23d9cec07c
The DRA74/72 control module pins have a weak pull up and pull down.
This is configured by bit offset 17. if BIT(17) is 1, a pull up is
selected, else a pull down is selected.
However, this pull resisstor is applied based on BIT(16) -
PULLUDENABLE - if BIT(18) is *0*, then pull as defined in BIT(17) is
applied, else no weak pulls are applied. We defined this in reverse.
Reference: Table 18-5 (Description of the pad configuration register
bits) in Technical Reference Manual Revision (DRA74x revision Q:
SPRUHI2Q Revised June 2014 and DRA72x revision F: SPRUHP2F - Revised
June 2014)
Fixes: 6e58b8f1da ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
52 lines
1.4 KiB
C
52 lines
1.4 KiB
C
/*
|
|
* This header provides constants for DRA pinctrl bindings.
|
|
*
|
|
* Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
|
|
* Author: Rajendra Nayak <rnayak@ti.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
|
|
#ifndef _DT_BINDINGS_PINCTRL_DRA_H
|
|
#define _DT_BINDINGS_PINCTRL_DRA_H
|
|
|
|
/* DRA7 mux mode options for each pin. See TRM for options */
|
|
#define MUX_MODE0 0x0
|
|
#define MUX_MODE1 0x1
|
|
#define MUX_MODE2 0x2
|
|
#define MUX_MODE3 0x3
|
|
#define MUX_MODE4 0x4
|
|
#define MUX_MODE5 0x5
|
|
#define MUX_MODE6 0x6
|
|
#define MUX_MODE7 0x7
|
|
#define MUX_MODE8 0x8
|
|
#define MUX_MODE9 0x9
|
|
#define MUX_MODE10 0xa
|
|
#define MUX_MODE11 0xb
|
|
#define MUX_MODE12 0xc
|
|
#define MUX_MODE13 0xd
|
|
#define MUX_MODE14 0xe
|
|
#define MUX_MODE15 0xf
|
|
|
|
#define PULL_ENA (0 << 16)
|
|
#define PULL_DIS (1 << 16)
|
|
#define PULL_UP (1 << 17)
|
|
#define INPUT_EN (1 << 18)
|
|
#define SLEWCONTROL (1 << 19)
|
|
#define WAKEUP_EN (1 << 24)
|
|
#define WAKEUP_EVENT (1 << 25)
|
|
|
|
/* Active pin states */
|
|
#define PIN_OUTPUT (0 | PULL_DIS)
|
|
#define PIN_OUTPUT_PULLUP (PIN_OUTPUT | PULL_ENA | PULL_UP)
|
|
#define PIN_OUTPUT_PULLDOWN (PIN_OUTPUT | PULL_ENA)
|
|
#define PIN_INPUT (INPUT_EN | PULL_DIS)
|
|
#define PIN_INPUT_SLEW (INPUT_EN | SLEWCONTROL)
|
|
#define PIN_INPUT_PULLUP (PULL_ENA | INPUT_EN | PULL_UP)
|
|
#define PIN_INPUT_PULLDOWN (PULL_ENA | INPUT_EN)
|
|
|
|
#endif
|
|
|