forked from Minki/linux
366f0a0f98
Datasheet says that the Message Port bit should not be set for the CPU port. Having it set causes DSA tagged packets to be sent to the CPU port roughly every 30 seconds. Those packets are the same as real packets forwarded between switch ports if the switch is configured for switching between multiple ports. The packets are then bridged by the software bridge, resulting in duplicated packets on the network. Reported-by: Andrew Lunn <andrew@lunn.ch> Cc: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
787 lines
17 KiB
C
787 lines
17 KiB
C
/*
|
|
* net/dsa/mv88e6xxx.c - Marvell 88e6xxx switch chip support
|
|
* Copyright (c) 2008 Marvell Semiconductor
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*/
|
|
|
|
#include <linux/delay.h>
|
|
#include <linux/jiffies.h>
|
|
#include <linux/list.h>
|
|
#include <linux/module.h>
|
|
#include <linux/netdevice.h>
|
|
#include <linux/phy.h>
|
|
#include <net/dsa.h>
|
|
#include "mv88e6xxx.h"
|
|
|
|
/* If the switch's ADDR[4:0] strap pins are strapped to zero, it will
|
|
* use all 32 SMI bus addresses on its SMI bus, and all switch registers
|
|
* will be directly accessible on some {device address,register address}
|
|
* pair. If the ADDR[4:0] pins are not strapped to zero, the switch
|
|
* will only respond to SMI transactions to that specific address, and
|
|
* an indirect addressing mechanism needs to be used to access its
|
|
* registers.
|
|
*/
|
|
static int mv88e6xxx_reg_wait_ready(struct mii_bus *bus, int sw_addr)
|
|
{
|
|
int ret;
|
|
int i;
|
|
|
|
for (i = 0; i < 16; i++) {
|
|
ret = mdiobus_read(bus, sw_addr, 0);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
if ((ret & 0x8000) == 0)
|
|
return 0;
|
|
}
|
|
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
int __mv88e6xxx_reg_read(struct mii_bus *bus, int sw_addr, int addr, int reg)
|
|
{
|
|
int ret;
|
|
|
|
if (sw_addr == 0)
|
|
return mdiobus_read(bus, addr, reg);
|
|
|
|
/* Wait for the bus to become free. */
|
|
ret = mv88e6xxx_reg_wait_ready(bus, sw_addr);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Transmit the read command. */
|
|
ret = mdiobus_write(bus, sw_addr, 0, 0x9800 | (addr << 5) | reg);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Wait for the read command to complete. */
|
|
ret = mv88e6xxx_reg_wait_ready(bus, sw_addr);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Read the data. */
|
|
ret = mdiobus_read(bus, sw_addr, 1);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return ret & 0xffff;
|
|
}
|
|
|
|
int mv88e6xxx_reg_read(struct dsa_switch *ds, int addr, int reg)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
struct mii_bus *bus = dsa_host_dev_to_mii_bus(ds->master_dev);
|
|
int ret;
|
|
|
|
if (bus == NULL)
|
|
return -EINVAL;
|
|
|
|
mutex_lock(&ps->smi_mutex);
|
|
ret = __mv88e6xxx_reg_read(bus, ds->pd->sw_addr, addr, reg);
|
|
mutex_unlock(&ps->smi_mutex);
|
|
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
dev_dbg(ds->master_dev, "<- addr: 0x%.2x reg: 0x%.2x val: 0x%.4x\n",
|
|
addr, reg, ret);
|
|
|
|
return ret;
|
|
}
|
|
|
|
int __mv88e6xxx_reg_write(struct mii_bus *bus, int sw_addr, int addr,
|
|
int reg, u16 val)
|
|
{
|
|
int ret;
|
|
|
|
if (sw_addr == 0)
|
|
return mdiobus_write(bus, addr, reg, val);
|
|
|
|
/* Wait for the bus to become free. */
|
|
ret = mv88e6xxx_reg_wait_ready(bus, sw_addr);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Transmit the data to write. */
|
|
ret = mdiobus_write(bus, sw_addr, 1, val);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Transmit the write command. */
|
|
ret = mdiobus_write(bus, sw_addr, 0, 0x9400 | (addr << 5) | reg);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Wait for the write command to complete. */
|
|
ret = mv88e6xxx_reg_wait_ready(bus, sw_addr);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int mv88e6xxx_reg_write(struct dsa_switch *ds, int addr, int reg, u16 val)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
struct mii_bus *bus = dsa_host_dev_to_mii_bus(ds->master_dev);
|
|
int ret;
|
|
|
|
if (bus == NULL)
|
|
return -EINVAL;
|
|
|
|
dev_dbg(ds->master_dev, "-> addr: 0x%.2x reg: 0x%.2x val: 0x%.4x\n",
|
|
addr, reg, val);
|
|
|
|
mutex_lock(&ps->smi_mutex);
|
|
ret = __mv88e6xxx_reg_write(bus, ds->pd->sw_addr, addr, reg, val);
|
|
mutex_unlock(&ps->smi_mutex);
|
|
|
|
return ret;
|
|
}
|
|
|
|
int mv88e6xxx_config_prio(struct dsa_switch *ds)
|
|
{
|
|
/* Configure the IP ToS mapping registers. */
|
|
REG_WRITE(REG_GLOBAL, 0x10, 0x0000);
|
|
REG_WRITE(REG_GLOBAL, 0x11, 0x0000);
|
|
REG_WRITE(REG_GLOBAL, 0x12, 0x5555);
|
|
REG_WRITE(REG_GLOBAL, 0x13, 0x5555);
|
|
REG_WRITE(REG_GLOBAL, 0x14, 0xaaaa);
|
|
REG_WRITE(REG_GLOBAL, 0x15, 0xaaaa);
|
|
REG_WRITE(REG_GLOBAL, 0x16, 0xffff);
|
|
REG_WRITE(REG_GLOBAL, 0x17, 0xffff);
|
|
|
|
/* Configure the IEEE 802.1p priority mapping register. */
|
|
REG_WRITE(REG_GLOBAL, 0x18, 0xfa41);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int mv88e6xxx_set_addr_direct(struct dsa_switch *ds, u8 *addr)
|
|
{
|
|
REG_WRITE(REG_GLOBAL, 0x01, (addr[0] << 8) | addr[1]);
|
|
REG_WRITE(REG_GLOBAL, 0x02, (addr[2] << 8) | addr[3]);
|
|
REG_WRITE(REG_GLOBAL, 0x03, (addr[4] << 8) | addr[5]);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int mv88e6xxx_set_addr_indirect(struct dsa_switch *ds, u8 *addr)
|
|
{
|
|
int i;
|
|
int ret;
|
|
|
|
for (i = 0; i < 6; i++) {
|
|
int j;
|
|
|
|
/* Write the MAC address byte. */
|
|
REG_WRITE(REG_GLOBAL2, 0x0d, 0x8000 | (i << 8) | addr[i]);
|
|
|
|
/* Wait for the write to complete. */
|
|
for (j = 0; j < 16; j++) {
|
|
ret = REG_READ(REG_GLOBAL2, 0x0d);
|
|
if ((ret & 0x8000) == 0)
|
|
break;
|
|
}
|
|
if (j == 16)
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
int mv88e6xxx_phy_read(struct dsa_switch *ds, int addr, int regnum)
|
|
{
|
|
if (addr >= 0)
|
|
return mv88e6xxx_reg_read(ds, addr, regnum);
|
|
return 0xffff;
|
|
}
|
|
|
|
int mv88e6xxx_phy_write(struct dsa_switch *ds, int addr, int regnum, u16 val)
|
|
{
|
|
if (addr >= 0)
|
|
return mv88e6xxx_reg_write(ds, addr, regnum, val);
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_NET_DSA_MV88E6XXX_NEED_PPU
|
|
static int mv88e6xxx_ppu_disable(struct dsa_switch *ds)
|
|
{
|
|
int ret;
|
|
unsigned long timeout;
|
|
|
|
ret = REG_READ(REG_GLOBAL, 0x04);
|
|
REG_WRITE(REG_GLOBAL, 0x04, ret & ~0x4000);
|
|
|
|
timeout = jiffies + 1 * HZ;
|
|
while (time_before(jiffies, timeout)) {
|
|
ret = REG_READ(REG_GLOBAL, 0x00);
|
|
usleep_range(1000, 2000);
|
|
if ((ret & 0xc000) != 0xc000)
|
|
return 0;
|
|
}
|
|
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
static int mv88e6xxx_ppu_enable(struct dsa_switch *ds)
|
|
{
|
|
int ret;
|
|
unsigned long timeout;
|
|
|
|
ret = REG_READ(REG_GLOBAL, 0x04);
|
|
REG_WRITE(REG_GLOBAL, 0x04, ret | 0x4000);
|
|
|
|
timeout = jiffies + 1 * HZ;
|
|
while (time_before(jiffies, timeout)) {
|
|
ret = REG_READ(REG_GLOBAL, 0x00);
|
|
usleep_range(1000, 2000);
|
|
if ((ret & 0xc000) == 0xc000)
|
|
return 0;
|
|
}
|
|
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
static void mv88e6xxx_ppu_reenable_work(struct work_struct *ugly)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps;
|
|
|
|
ps = container_of(ugly, struct mv88e6xxx_priv_state, ppu_work);
|
|
if (mutex_trylock(&ps->ppu_mutex)) {
|
|
struct dsa_switch *ds = ((struct dsa_switch *)ps) - 1;
|
|
|
|
if (mv88e6xxx_ppu_enable(ds) == 0)
|
|
ps->ppu_disabled = 0;
|
|
mutex_unlock(&ps->ppu_mutex);
|
|
}
|
|
}
|
|
|
|
static void mv88e6xxx_ppu_reenable_timer(unsigned long _ps)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = (void *)_ps;
|
|
|
|
schedule_work(&ps->ppu_work);
|
|
}
|
|
|
|
static int mv88e6xxx_ppu_access_get(struct dsa_switch *ds)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
int ret;
|
|
|
|
mutex_lock(&ps->ppu_mutex);
|
|
|
|
/* If the PHY polling unit is enabled, disable it so that
|
|
* we can access the PHY registers. If it was already
|
|
* disabled, cancel the timer that is going to re-enable
|
|
* it.
|
|
*/
|
|
if (!ps->ppu_disabled) {
|
|
ret = mv88e6xxx_ppu_disable(ds);
|
|
if (ret < 0) {
|
|
mutex_unlock(&ps->ppu_mutex);
|
|
return ret;
|
|
}
|
|
ps->ppu_disabled = 1;
|
|
} else {
|
|
del_timer(&ps->ppu_timer);
|
|
ret = 0;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void mv88e6xxx_ppu_access_put(struct dsa_switch *ds)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
|
|
/* Schedule a timer to re-enable the PHY polling unit. */
|
|
mod_timer(&ps->ppu_timer, jiffies + msecs_to_jiffies(10));
|
|
mutex_unlock(&ps->ppu_mutex);
|
|
}
|
|
|
|
void mv88e6xxx_ppu_state_init(struct dsa_switch *ds)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
|
|
mutex_init(&ps->ppu_mutex);
|
|
INIT_WORK(&ps->ppu_work, mv88e6xxx_ppu_reenable_work);
|
|
init_timer(&ps->ppu_timer);
|
|
ps->ppu_timer.data = (unsigned long)ps;
|
|
ps->ppu_timer.function = mv88e6xxx_ppu_reenable_timer;
|
|
}
|
|
|
|
int mv88e6xxx_phy_read_ppu(struct dsa_switch *ds, int addr, int regnum)
|
|
{
|
|
int ret;
|
|
|
|
ret = mv88e6xxx_ppu_access_get(ds);
|
|
if (ret >= 0) {
|
|
ret = mv88e6xxx_reg_read(ds, addr, regnum);
|
|
mv88e6xxx_ppu_access_put(ds);
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
int mv88e6xxx_phy_write_ppu(struct dsa_switch *ds, int addr,
|
|
int regnum, u16 val)
|
|
{
|
|
int ret;
|
|
|
|
ret = mv88e6xxx_ppu_access_get(ds);
|
|
if (ret >= 0) {
|
|
ret = mv88e6xxx_reg_write(ds, addr, regnum, val);
|
|
mv88e6xxx_ppu_access_put(ds);
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
#endif
|
|
|
|
void mv88e6xxx_poll_link(struct dsa_switch *ds)
|
|
{
|
|
int i;
|
|
|
|
for (i = 0; i < DSA_MAX_PORTS; i++) {
|
|
struct net_device *dev;
|
|
int uninitialized_var(port_status);
|
|
int link;
|
|
int speed;
|
|
int duplex;
|
|
int fc;
|
|
|
|
dev = ds->ports[i];
|
|
if (dev == NULL)
|
|
continue;
|
|
|
|
link = 0;
|
|
if (dev->flags & IFF_UP) {
|
|
port_status = mv88e6xxx_reg_read(ds, REG_PORT(i), 0x00);
|
|
if (port_status < 0)
|
|
continue;
|
|
|
|
link = !!(port_status & 0x0800);
|
|
}
|
|
|
|
if (!link) {
|
|
if (netif_carrier_ok(dev)) {
|
|
netdev_info(dev, "link down\n");
|
|
netif_carrier_off(dev);
|
|
}
|
|
continue;
|
|
}
|
|
|
|
switch (port_status & 0x0300) {
|
|
case 0x0000:
|
|
speed = 10;
|
|
break;
|
|
case 0x0100:
|
|
speed = 100;
|
|
break;
|
|
case 0x0200:
|
|
speed = 1000;
|
|
break;
|
|
default:
|
|
speed = -1;
|
|
break;
|
|
}
|
|
duplex = (port_status & 0x0400) ? 1 : 0;
|
|
fc = (port_status & 0x8000) ? 1 : 0;
|
|
|
|
if (!netif_carrier_ok(dev)) {
|
|
netdev_info(dev,
|
|
"link up, %d Mb/s, %s duplex, flow control %sabled\n",
|
|
speed,
|
|
duplex ? "full" : "half",
|
|
fc ? "en" : "dis");
|
|
netif_carrier_on(dev);
|
|
}
|
|
}
|
|
}
|
|
|
|
static int mv88e6xxx_stats_wait(struct dsa_switch *ds)
|
|
{
|
|
int ret;
|
|
int i;
|
|
|
|
for (i = 0; i < 10; i++) {
|
|
ret = REG_READ(REG_GLOBAL, 0x1d);
|
|
if ((ret & 0x8000) == 0)
|
|
return 0;
|
|
}
|
|
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
static int mv88e6xxx_stats_snapshot(struct dsa_switch *ds, int port)
|
|
{
|
|
int ret;
|
|
|
|
/* Snapshot the hardware statistics counters for this port. */
|
|
REG_WRITE(REG_GLOBAL, 0x1d, 0xdc00 | port);
|
|
|
|
/* Wait for the snapshotting to complete. */
|
|
ret = mv88e6xxx_stats_wait(ds);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void mv88e6xxx_stats_read(struct dsa_switch *ds, int stat, u32 *val)
|
|
{
|
|
u32 _val;
|
|
int ret;
|
|
|
|
*val = 0;
|
|
|
|
ret = mv88e6xxx_reg_write(ds, REG_GLOBAL, 0x1d, 0xcc00 | stat);
|
|
if (ret < 0)
|
|
return;
|
|
|
|
ret = mv88e6xxx_stats_wait(ds);
|
|
if (ret < 0)
|
|
return;
|
|
|
|
ret = mv88e6xxx_reg_read(ds, REG_GLOBAL, 0x1e);
|
|
if (ret < 0)
|
|
return;
|
|
|
|
_val = ret << 16;
|
|
|
|
ret = mv88e6xxx_reg_read(ds, REG_GLOBAL, 0x1f);
|
|
if (ret < 0)
|
|
return;
|
|
|
|
*val = _val | ret;
|
|
}
|
|
|
|
void mv88e6xxx_get_strings(struct dsa_switch *ds,
|
|
int nr_stats, struct mv88e6xxx_hw_stat *stats,
|
|
int port, uint8_t *data)
|
|
{
|
|
int i;
|
|
|
|
for (i = 0; i < nr_stats; i++) {
|
|
memcpy(data + i * ETH_GSTRING_LEN,
|
|
stats[i].string, ETH_GSTRING_LEN);
|
|
}
|
|
}
|
|
|
|
void mv88e6xxx_get_ethtool_stats(struct dsa_switch *ds,
|
|
int nr_stats, struct mv88e6xxx_hw_stat *stats,
|
|
int port, uint64_t *data)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
int ret;
|
|
int i;
|
|
|
|
mutex_lock(&ps->stats_mutex);
|
|
|
|
ret = mv88e6xxx_stats_snapshot(ds, port);
|
|
if (ret < 0) {
|
|
mutex_unlock(&ps->stats_mutex);
|
|
return;
|
|
}
|
|
|
|
/* Read each of the counters. */
|
|
for (i = 0; i < nr_stats; i++) {
|
|
struct mv88e6xxx_hw_stat *s = stats + i;
|
|
u32 low;
|
|
u32 high = 0;
|
|
|
|
if (s->reg >= 0x100) {
|
|
int ret;
|
|
|
|
ret = mv88e6xxx_reg_read(ds, REG_PORT(port),
|
|
s->reg - 0x100);
|
|
if (ret < 0)
|
|
goto error;
|
|
low = ret;
|
|
if (s->sizeof_stat == 4) {
|
|
ret = mv88e6xxx_reg_read(ds, REG_PORT(port),
|
|
s->reg - 0x100 + 1);
|
|
if (ret < 0)
|
|
goto error;
|
|
high = ret;
|
|
}
|
|
data[i] = (((u64)high) << 16) | low;
|
|
continue;
|
|
}
|
|
mv88e6xxx_stats_read(ds, s->reg, &low);
|
|
if (s->sizeof_stat == 8)
|
|
mv88e6xxx_stats_read(ds, s->reg + 1, &high);
|
|
|
|
data[i] = (((u64)high) << 32) | low;
|
|
}
|
|
error:
|
|
mutex_unlock(&ps->stats_mutex);
|
|
}
|
|
|
|
int mv88e6xxx_get_regs_len(struct dsa_switch *ds, int port)
|
|
{
|
|
return 32 * sizeof(u16);
|
|
}
|
|
|
|
void mv88e6xxx_get_regs(struct dsa_switch *ds, int port,
|
|
struct ethtool_regs *regs, void *_p)
|
|
{
|
|
u16 *p = _p;
|
|
int i;
|
|
|
|
regs->version = 0;
|
|
|
|
memset(p, 0xff, 32 * sizeof(u16));
|
|
|
|
for (i = 0; i < 32; i++) {
|
|
int ret;
|
|
|
|
ret = mv88e6xxx_reg_read(ds, REG_PORT(port), i);
|
|
if (ret >= 0)
|
|
p[i] = ret;
|
|
}
|
|
}
|
|
|
|
#ifdef CONFIG_NET_DSA_HWMON
|
|
|
|
int mv88e6xxx_get_temp(struct dsa_switch *ds, int *temp)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
int ret;
|
|
int val;
|
|
|
|
*temp = 0;
|
|
|
|
mutex_lock(&ps->phy_mutex);
|
|
|
|
ret = mv88e6xxx_phy_write(ds, 0x0, 0x16, 0x6);
|
|
if (ret < 0)
|
|
goto error;
|
|
|
|
/* Enable temperature sensor */
|
|
ret = mv88e6xxx_phy_read(ds, 0x0, 0x1a);
|
|
if (ret < 0)
|
|
goto error;
|
|
|
|
ret = mv88e6xxx_phy_write(ds, 0x0, 0x1a, ret | (1 << 5));
|
|
if (ret < 0)
|
|
goto error;
|
|
|
|
/* Wait for temperature to stabilize */
|
|
usleep_range(10000, 12000);
|
|
|
|
val = mv88e6xxx_phy_read(ds, 0x0, 0x1a);
|
|
if (val < 0) {
|
|
ret = val;
|
|
goto error;
|
|
}
|
|
|
|
/* Disable temperature sensor */
|
|
ret = mv88e6xxx_phy_write(ds, 0x0, 0x1a, ret & ~(1 << 5));
|
|
if (ret < 0)
|
|
goto error;
|
|
|
|
*temp = ((val & 0x1f) - 5) * 5;
|
|
|
|
error:
|
|
mv88e6xxx_phy_write(ds, 0x0, 0x16, 0x0);
|
|
mutex_unlock(&ps->phy_mutex);
|
|
return ret;
|
|
}
|
|
#endif /* CONFIG_NET_DSA_HWMON */
|
|
|
|
static int mv88e6xxx_wait(struct dsa_switch *ds, int reg, int offset, u16 mask)
|
|
{
|
|
unsigned long timeout = jiffies + HZ / 10;
|
|
|
|
while (time_before(jiffies, timeout)) {
|
|
int ret;
|
|
|
|
ret = REG_READ(reg, offset);
|
|
if (!(ret & mask))
|
|
return 0;
|
|
|
|
usleep_range(1000, 2000);
|
|
}
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
int mv88e6xxx_phy_wait(struct dsa_switch *ds)
|
|
{
|
|
return mv88e6xxx_wait(ds, REG_GLOBAL2, 0x18, 0x8000);
|
|
}
|
|
|
|
int mv88e6xxx_eeprom_load_wait(struct dsa_switch *ds)
|
|
{
|
|
return mv88e6xxx_wait(ds, REG_GLOBAL2, 0x14, 0x0800);
|
|
}
|
|
|
|
int mv88e6xxx_eeprom_busy_wait(struct dsa_switch *ds)
|
|
{
|
|
return mv88e6xxx_wait(ds, REG_GLOBAL2, 0x14, 0x8000);
|
|
}
|
|
|
|
int mv88e6xxx_phy_read_indirect(struct dsa_switch *ds, int addr, int regnum)
|
|
{
|
|
int ret;
|
|
|
|
REG_WRITE(REG_GLOBAL2, 0x18, 0x9800 | (addr << 5) | regnum);
|
|
|
|
ret = mv88e6xxx_phy_wait(ds);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
return REG_READ(REG_GLOBAL2, 0x19);
|
|
}
|
|
|
|
int mv88e6xxx_phy_write_indirect(struct dsa_switch *ds, int addr, int regnum,
|
|
u16 val)
|
|
{
|
|
REG_WRITE(REG_GLOBAL2, 0x19, val);
|
|
REG_WRITE(REG_GLOBAL2, 0x18, 0x9400 | (addr << 5) | regnum);
|
|
|
|
return mv88e6xxx_phy_wait(ds);
|
|
}
|
|
|
|
int mv88e6xxx_get_eee(struct dsa_switch *ds, int port, struct ethtool_eee *e)
|
|
{
|
|
int reg;
|
|
|
|
reg = mv88e6xxx_phy_read_indirect(ds, port, 16);
|
|
if (reg < 0)
|
|
return -EOPNOTSUPP;
|
|
|
|
e->eee_enabled = !!(reg & 0x0200);
|
|
e->tx_lpi_enabled = !!(reg & 0x0100);
|
|
|
|
reg = REG_READ(REG_PORT(port), 0);
|
|
e->eee_active = !!(reg & 0x0040);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int mv88e6xxx_eee_enable_set(struct dsa_switch *ds, int port,
|
|
bool eee_enabled, bool tx_lpi_enabled)
|
|
{
|
|
int reg, nreg;
|
|
|
|
reg = mv88e6xxx_phy_read_indirect(ds, port, 16);
|
|
if (reg < 0)
|
|
return reg;
|
|
|
|
nreg = reg & ~0x0300;
|
|
if (eee_enabled)
|
|
nreg |= 0x0200;
|
|
if (tx_lpi_enabled)
|
|
nreg |= 0x0100;
|
|
|
|
if (nreg != reg)
|
|
return mv88e6xxx_phy_write_indirect(ds, port, 16, nreg);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int mv88e6xxx_set_eee(struct dsa_switch *ds, int port,
|
|
struct phy_device *phydev, struct ethtool_eee *e)
|
|
{
|
|
int ret;
|
|
|
|
ret = mv88e6xxx_eee_enable_set(ds, port, e->eee_enabled,
|
|
e->tx_lpi_enabled);
|
|
if (ret)
|
|
return -EOPNOTSUPP;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int mv88e6xxx_setup_port_common(struct dsa_switch *ds, int port)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
int ret, reg;
|
|
|
|
mutex_lock(&ps->smi_mutex);
|
|
|
|
/* Port Control 1: disable trunking, disable sending
|
|
* learning messages to this port.
|
|
*/
|
|
ret = _mv88e6xxx_reg_write(ds, REG_PORT(port), 0x05, 0x0000);
|
|
if (ret)
|
|
goto abort;
|
|
|
|
/* Port based VLAN map: give each port its own address
|
|
* database, allow the CPU port to talk to each of the 'real'
|
|
* ports, and allow each of the 'real' ports to only talk to
|
|
* the upstream port.
|
|
*/
|
|
reg = (port & 0xf) << 12;
|
|
if (dsa_is_cpu_port(ds, port))
|
|
reg |= ds->phys_port_mask;
|
|
else
|
|
reg |= 1 << dsa_upstream_port(ds);
|
|
|
|
ret = _mv88e6xxx_reg_write(ds, REG_PORT(port), 0x06, reg);
|
|
if (ret)
|
|
goto abort;
|
|
|
|
/* Default VLAN ID and priority: don't set a default VLAN
|
|
* ID, and set the default packet priority to zero.
|
|
*/
|
|
ret = _mv88e6xxx_reg_write(ds, REG_PORT(port), 0x07, 0x0000);
|
|
abort:
|
|
mutex_unlock(&ps->smi_mutex);
|
|
return ret;
|
|
}
|
|
|
|
int mv88e6xxx_setup_common(struct dsa_switch *ds)
|
|
{
|
|
struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
|
|
|
|
mutex_init(&ps->smi_mutex);
|
|
mutex_init(&ps->stats_mutex);
|
|
mutex_init(&ps->phy_mutex);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __init mv88e6xxx_init(void)
|
|
{
|
|
#if IS_ENABLED(CONFIG_NET_DSA_MV88E6131)
|
|
register_switch_driver(&mv88e6131_switch_driver);
|
|
#endif
|
|
#if IS_ENABLED(CONFIG_NET_DSA_MV88E6123_61_65)
|
|
register_switch_driver(&mv88e6123_61_65_switch_driver);
|
|
#endif
|
|
#if IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
|
|
register_switch_driver(&mv88e6352_switch_driver);
|
|
#endif
|
|
#if IS_ENABLED(CONFIG_NET_DSA_MV88E6171)
|
|
register_switch_driver(&mv88e6171_switch_driver);
|
|
#endif
|
|
return 0;
|
|
}
|
|
module_init(mv88e6xxx_init);
|
|
|
|
static void __exit mv88e6xxx_cleanup(void)
|
|
{
|
|
#if IS_ENABLED(CONFIG_NET_DSA_MV88E6171)
|
|
unregister_switch_driver(&mv88e6171_switch_driver);
|
|
#endif
|
|
#if IS_ENABLED(CONFIG_NET_DSA_MV88E6123_61_65)
|
|
unregister_switch_driver(&mv88e6123_61_65_switch_driver);
|
|
#endif
|
|
#if IS_ENABLED(CONFIG_NET_DSA_MV88E6131)
|
|
unregister_switch_driver(&mv88e6131_switch_driver);
|
|
#endif
|
|
}
|
|
module_exit(mv88e6xxx_cleanup);
|
|
|
|
MODULE_AUTHOR("Lennert Buytenhek <buytenh@wantstofly.org>");
|
|
MODULE_DESCRIPTION("Driver for Marvell 88E6XXX ethernet switch chips");
|
|
MODULE_LICENSE("GPL");
|