forked from Minki/linux
7c60375083
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
180 lines
6.9 KiB
Plaintext
180 lines
6.9 KiB
Plaintext
Linux I2C slave interface description
|
|
=====================================
|
|
|
|
by Wolfram Sang <wsa@sang-engineering.com> in 2014-15
|
|
|
|
Linux can also be an I2C slave in case I2C controllers have slave support.
|
|
Besides this HW requirement, one also needs a software backend providing the
|
|
actual functionality. An example for this is the slave-eeprom driver, which
|
|
acts as a dual memory driver. While another I2C master on the bus can access it
|
|
like a regular EEPROM, the Linux I2C slave can access the content via sysfs and
|
|
retrieve/provide information as needed. The software backend driver and the I2C
|
|
bus driver communicate via events. Here is a small graph visualizing the data
|
|
flow and the means by which data is transported. The dotted line marks only one
|
|
example. The backend could also use e.g. a character device, be in-kernel
|
|
only, or something completely different:
|
|
|
|
|
|
e.g. sysfs I2C slave events I/O registers
|
|
+-----------+ v +---------+ v +--------+ v +------------+
|
|
| Userspace +........+ Backend +-----------+ Driver +-----+ Controller |
|
|
+-----------+ +---------+ +--------+ +------------+
|
|
| |
|
|
----------------------------------------------------------------+-- I2C
|
|
--------------------------------------------------------------+---- Bus
|
|
|
|
Note: Technically, there is also the I2C core between the backend and the
|
|
driver. However, at this time of writing, the layer is transparent.
|
|
|
|
|
|
User manual
|
|
===========
|
|
|
|
I2C slave backends behave like standard I2C clients. So, you can instantiate
|
|
them like described in the document 'instantiating-devices'. A quick example
|
|
for instantiating the slave-eeprom driver from userspace:
|
|
|
|
# echo 0-0064 > /sys/bus/i2c/drivers/i2c-slave-eeprom/bind
|
|
|
|
Each backend should come with separate documentation to describe its specific
|
|
behaviour and setup.
|
|
|
|
|
|
Developer manual
|
|
================
|
|
|
|
I2C slave events
|
|
----------------
|
|
|
|
The bus driver sends an event to the backend using the following function:
|
|
|
|
ret = i2c_slave_event(client, event, &val)
|
|
|
|
'client' describes the i2c slave device. 'event' is one of the special event
|
|
types described hereafter. 'val' holds an u8 value for the data byte to be
|
|
read/written and is thus bidirectional. The pointer to val must always be
|
|
provided even if val is not used for an event, i.e. don't use NULL here. 'ret'
|
|
is the return value from the backend. Mandatory events must be provided by the
|
|
bus drivers and must be checked for by backend drivers.
|
|
|
|
Event types:
|
|
|
|
* I2C_SLAVE_WRITE_REQUESTED (mandatory)
|
|
|
|
'val': unused
|
|
'ret': always 0
|
|
|
|
Another I2C master wants to write data to us. This event should be sent once
|
|
our own address and the write bit was detected. The data did not arrive yet, so
|
|
there is nothing to process or return. Wakeup or initialization probably needs
|
|
to be done, though.
|
|
|
|
* I2C_SLAVE_READ_REQUESTED (mandatory)
|
|
|
|
'val': backend returns first byte to be sent
|
|
'ret': always 0
|
|
|
|
Another I2C master wants to read data from us. This event should be sent once
|
|
our own address and the read bit was detected. After returning, the bus driver
|
|
should transmit the first byte.
|
|
|
|
* I2C_SLAVE_WRITE_RECEIVED (mandatory)
|
|
|
|
'val': bus driver delivers received byte
|
|
'ret': 0 if the byte should be acked, some errno if the byte should be nacked
|
|
|
|
Another I2C master has sent a byte to us which needs to be set in 'val'. If 'ret'
|
|
is zero, the bus driver should ack this byte. If 'ret' is an errno, then the byte
|
|
should be nacked.
|
|
|
|
* I2C_SLAVE_READ_PROCESSED (mandatory)
|
|
|
|
'val': backend returns next byte to be sent
|
|
'ret': always 0
|
|
|
|
The bus driver requests the next byte to be sent to another I2C master in
|
|
'val'. Important: This does not mean that the previous byte has been acked, it
|
|
only means that the previous byte is shifted out to the bus! To ensure seamless
|
|
transmission, most hardware requests the next byte when the previous one is
|
|
still shifted out. If the master sends NACK and stops reading after the byte
|
|
currently shifted out, this byte requested here is never used. It very likely
|
|
needs to be sent again on the next I2C_SLAVE_READ_REQUEST, depending a bit on
|
|
your backend, though.
|
|
|
|
* I2C_SLAVE_STOP (mandatory)
|
|
|
|
'val': unused
|
|
'ret': always 0
|
|
|
|
A stop condition was received. This can happen anytime and the backend should
|
|
reset its state machine for I2C transfers to be able to receive new requests.
|
|
|
|
|
|
Software backends
|
|
-----------------
|
|
|
|
If you want to write a software backend:
|
|
|
|
* use a standard i2c_driver and its matching mechanisms
|
|
* write the slave_callback which handles the above slave events
|
|
(best using a state machine)
|
|
* register this callback via i2c_slave_register()
|
|
|
|
Check the i2c-slave-eeprom driver as an example.
|
|
|
|
|
|
Bus driver support
|
|
------------------
|
|
|
|
If you want to add slave support to the bus driver:
|
|
|
|
* implement calls to register/unregister the slave and add those to the
|
|
struct i2c_algorithm. When registering, you probably need to set the i2c
|
|
slave address and enable slave specific interrupts. If you use runtime pm, you
|
|
should use pm_runtime_forbid() because your device usually needs to be powered
|
|
on always to be able to detect its slave address. When unregistering, do the
|
|
inverse of the above.
|
|
|
|
* Catch the slave interrupts and send appropriate i2c_slave_events to the backend.
|
|
|
|
Check the i2c-rcar driver as an example.
|
|
|
|
|
|
About ACK/NACK
|
|
--------------
|
|
|
|
It is good behaviour to always ACK the address phase, so the master knows if a
|
|
device is basically present or if it mysteriously disappeared. Using NACK to
|
|
state being busy is troublesome. SMBus demands to always ACK the address phase,
|
|
while the I2C specification is more loose on that. Most I2C controllers also
|
|
automatically ACK when detecting their slave addresses, so there is no option
|
|
to NACK them. For those reasons, this API does not support NACK in the address
|
|
phase.
|
|
|
|
Currently, there is no slave event to report if the master did ACK or NACK a
|
|
byte when it reads from us. We could make this an optional event if the need
|
|
arises. However, cases should be extremely rare because the master is expected
|
|
to send STOP after that and we have an event for that. Also, keep in mind not
|
|
all I2C controllers have the possibility to report that event.
|
|
|
|
|
|
About buffers
|
|
-------------
|
|
|
|
During development of this API, the question of using buffers instead of just
|
|
bytes came up. Such an extension might be possible, usefulness is unclear at
|
|
this time of writing. Some points to keep in mind when using buffers:
|
|
|
|
* Buffers should be opt-in and slave drivers will always have to support
|
|
byte-based transactions as the ultimate fallback because this is how the
|
|
majority of HW works.
|
|
|
|
* For backends simulating hardware registers, buffers are not helpful because
|
|
on writes an action should be immediately triggered. For reads, the data in
|
|
the buffer might get stale.
|
|
|
|
* A master can send STOP at any time. For partially transferred buffers, this
|
|
means additional code to handle this exception. Such code tends to be
|
|
error-prone.
|
|
|