forked from Minki/linux
35ef7d689d
This adds support for W5500 chip. W5500 has similar register and memory organization with W5100 and W5200. There are a few important differences listed below but it is still possible to share common code with W5100 and W5200. * W5500 register and memory are organized by multiple blocks. Each one is selected by 16bits offset address and 5bits block select bits. But the existing register access operations take u16 address. This change extends the addess by u32 address and put offset address to lower 16bits and block select bits to upper 16bits. This change also adds the offset addresses for socket register and TX/RX memory blocks to the driver private data structure in order to reduce conditional switches for each chip. * W5500 has the different register offset for socket interrupt mask register. Newly added internal functions w5100_enable_intr() and w5100_disable_intr() take care of the diffrence. * W5500 has the different register offset for retry time-value register. But this register is only used to verify that the reset value is correctly read at initialization. So move the verification to w5100_hw_reset() which already does different things for different chips. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
87 lines
2.6 KiB
Plaintext
87 lines
2.6 KiB
Plaintext
#
|
|
# WIZnet devices configuration
|
|
#
|
|
|
|
config NET_VENDOR_WIZNET
|
|
bool "WIZnet devices"
|
|
depends on HAS_IOMEM
|
|
default y
|
|
---help---
|
|
If you have a network (Ethernet) card belonging to this class, say Y.
|
|
|
|
Note that the answer to this question doesn't directly affect the
|
|
kernel: saying N will just cause the configurator to skip all
|
|
the questions about WIZnet devices. If you say Y, you will be asked
|
|
for your specific card in the following questions.
|
|
|
|
if NET_VENDOR_WIZNET
|
|
|
|
config WIZNET_W5100
|
|
tristate "WIZnet W5100 Ethernet support"
|
|
depends on HAS_IOMEM
|
|
---help---
|
|
Support for WIZnet W5100 chips.
|
|
|
|
W5100 is a single chip with integrated 10/100 Ethernet MAC,
|
|
PHY and hardware TCP/IP stack, but this driver is limited to
|
|
the MAC and PHY functions only, onchip TCP/IP is unused.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called w5100.
|
|
|
|
config WIZNET_W5300
|
|
tristate "WIZnet W5300 Ethernet support"
|
|
depends on HAS_IOMEM
|
|
---help---
|
|
Support for WIZnet W5300 chips.
|
|
|
|
W5300 is a single chip with integrated 10/100 Ethernet MAC,
|
|
PHY and hardware TCP/IP stack, but this driver is limited to
|
|
the MAC and PHY functions only, onchip TCP/IP is unused.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called w5300.
|
|
|
|
choice
|
|
prompt "WIZnet interface mode"
|
|
depends on WIZNET_W5100 || WIZNET_W5300
|
|
default WIZNET_BUS_ANY
|
|
|
|
config WIZNET_BUS_DIRECT
|
|
bool "Direct address bus mode"
|
|
---help---
|
|
In direct address mode host system can directly access all registers
|
|
after mapping to Memory-Mapped I/O space.
|
|
|
|
config WIZNET_BUS_INDIRECT
|
|
bool "Indirect address bus mode"
|
|
---help---
|
|
In indirect address mode host system indirectly accesses registers
|
|
using Indirect Mode Address Register and Indirect Mode Data Register,
|
|
which are directly mapped to Memory-Mapped I/O space.
|
|
|
|
config WIZNET_BUS_ANY
|
|
bool "Select interface mode in runtime"
|
|
---help---
|
|
If interface mode is unknown in compile time, it can be selected
|
|
in runtime from board/platform resources configuration.
|
|
|
|
Performance may decrease compared to explicitly selected bus mode.
|
|
endchoice
|
|
|
|
config WIZNET_W5100_SPI
|
|
tristate "WIZnet W5100/W5200/W5500 Ethernet support for SPI mode"
|
|
depends on WIZNET_BUS_ANY && WIZNET_W5100
|
|
depends on SPI
|
|
---help---
|
|
In SPI mode host system accesses registers using SPI protocol
|
|
(mode 0) on the SPI bus.
|
|
|
|
Performance decreases compared to other bus interface mode.
|
|
In W5100 SPI mode, burst READ/WRITE processing are not provided.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called w5100-spi.
|
|
|
|
endif # NET_VENDOR_WIZNET
|