forked from Minki/linux
246835fccd
The Cintiq 24HD has three LEDs on the left side of the tablet and three LEDs on the right side of the tablet. Switching to LED 0, 1, or 2 will enable the top, middle, or bottom LED for the respective side. Switching to LED 3 turns off the LEDs on the respective side. Signed-off-by: Jason Gerecke <killertofu@gmail.com> Reviewed-by: Ping Cheng <pingc@wacom.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
74 lines
3.0 KiB
Plaintext
74 lines
3.0 KiB
Plaintext
What: /sys/class/hidraw/hidraw*/device/speed
|
|
Date: April 2010
|
|
Kernel Version: 2.6.35
|
|
Contact: linux-bluetooth@vger.kernel.org
|
|
Description:
|
|
The /sys/class/hidraw/hidraw*/device/speed file controls
|
|
reporting speed of Wacom bluetooth tablet. Reading from
|
|
this file returns 1 if tablet reports in high speed mode
|
|
or 0 otherwise. Writing to this file one of these values
|
|
switches reporting speed.
|
|
|
|
What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/led
|
|
Date: August 2011
|
|
Contact: linux-input@vger.kernel.org
|
|
Description:
|
|
Attribute group for control of the status LEDs and the OLEDs.
|
|
This attribute group is only available for Intuos 4 M, L,
|
|
and XL (with LEDs and OLEDs) and Cintiq 21UX2 and Cintiq 24HD
|
|
(LEDs only). Therefore its presence implicitly signifies the
|
|
presence of said LEDs and OLEDs on the tablet device.
|
|
|
|
What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status0_luminance
|
|
Date: August 2011
|
|
Contact: linux-input@vger.kernel.org
|
|
Description:
|
|
Writing to this file sets the status LED luminance (1..127)
|
|
when the stylus does not touch the tablet surface, and no
|
|
button is pressed on the stylus. This luminance level is
|
|
normally lower than the level when a button is pressed.
|
|
|
|
What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status1_luminance
|
|
Date: August 2011
|
|
Contact: linux-input@vger.kernel.org
|
|
Description:
|
|
Writing to this file sets the status LED luminance (1..127)
|
|
when the stylus touches the tablet surface, or any button is
|
|
pressed on the stylus.
|
|
|
|
What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status_led0_select
|
|
Date: August 2011
|
|
Contact: linux-input@vger.kernel.org
|
|
Description:
|
|
Writing to this file sets which one of the four (for Intuos 4)
|
|
or of the right four (for Cintiq 21UX2 and Cintiq 24HD) status
|
|
LEDs is active (0..3). The other three LEDs on the same side are
|
|
always inactive.
|
|
|
|
What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status_led1_select
|
|
Date: September 2011
|
|
Contact: linux-input@vger.kernel.org
|
|
Description:
|
|
Writing to this file sets which one of the left four (for Cintiq 21UX2
|
|
and Cintiq 24HD) status LEDs is active (0..3). The other three LEDs on
|
|
the left are always inactive.
|
|
|
|
What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/buttons_luminance
|
|
Date: August 2011
|
|
Contact: linux-input@vger.kernel.org
|
|
Description:
|
|
Writing to this file sets the overall luminance level (0..15)
|
|
of all eight button OLED displays.
|
|
|
|
What: /sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/button<n>_rawimg
|
|
Date: August 2011
|
|
Contact: linux-input@vger.kernel.org
|
|
Description:
|
|
When writing a 1024 byte raw image in Wacom Intuos 4
|
|
interleaving format to the file, the image shows up on Button N
|
|
of the device. The image is a 64x32 pixel 4-bit gray image. The
|
|
1024 byte binary is split up into 16x 64 byte chunks. Each 64
|
|
byte chunk encodes the image data for two consecutive lines on
|
|
the display. The low nibble of each byte contains the first
|
|
line, and the high nibble contains the second line.
|