linux/drivers/net/wireless/ti/wlcore
Arik Nemtsov 1ede950073 wlcore: decrease warning verbosity during recovery
Silently ignore repetitive scheduling of recovery work and commands
being passed to the bus when the HW is not available. This can happen
many times during recovery and slow it down. It also spams the kernel
logs.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-13 15:20:16 -05:00
..
acx.c wl18xx: move to new firmware (wl18xx-fw-3.bin) 2014-02-13 15:20:15 -05:00
acx.h wl18xx: move to new firmware (wl18xx-fw-3.bin) 2014-02-13 15:20:15 -05:00
boot.c wlcore: use single-role version when verifying the PLT firmware 2013-02-08 10:05:01 +02:00
boot.h
cmd.c wlcore: decrease warning verbosity during recovery 2014-02-13 15:20:16 -05:00
cmd.h wl18xx: move to new firmware (wl18xx-fw-3.bin) 2014-02-13 15:20:15 -05:00
conf.h wlcore: fwlog dynamic mem_block control 2013-10-23 09:47:40 +03:00
debug.h wlcore: use print_hex_dump_debug() 2013-03-25 12:36:24 +02:00
debugfs.c wlcore: print active channel in the driver_state 2013-10-23 09:47:39 +03:00
debugfs.h
event.c wlcore/wl12xx/wl18xx: configure num_links per-hw 2014-02-13 15:20:15 -05:00
event.h wlcore: support scan reports during periodic scan 2012-12-11 12:37:23 +02:00
hw_ops.h wlcore/wl12xx/wl18xx: simplify fw_status handling 2014-02-13 15:20:15 -05:00
ini.h
init.c wlcore: wl18xx: allow CCK rates for AP mode 2014-02-13 15:20:16 -05:00
init.h
io.c
io.h wlcore: block read/writes to FW during ELP 2014-02-13 15:20:14 -05:00
Kconfig Remove GENERIC_HARDIRQ config option 2013-09-13 15:09:52 +02:00
main.c wlcore: decrease warning verbosity during recovery 2014-02-13 15:20:16 -05:00
Makefile wlcore: move sysfs handling to a separate file 2013-06-17 11:56:59 +03:00
ps.c wlcore: AP: don't start mac80211 PS on non-peer HLIDs 2014-02-13 15:20:14 -05:00
ps.h
rx.c wlcore/wl12xx/wl18xx: configure num_links per-hw 2014-02-13 15:20:15 -05:00
rx.h wlcore/wl12xx/wl18xx: simplify fw_status handling 2014-02-13 15:20:15 -05:00
scan.c cfg80211: consolidate passive-scan and no-ibss flags 2013-11-25 20:49:35 +01:00
scan.h wlcore: support scan reports during periodic scan 2012-12-11 12:37:23 +02:00
sdio.c wlcore: remove newly introduced alloc/OOM messages 2013-02-11 15:34:58 -05:00
spi.c wireless: wlcore: use dev_get_platdata() 2013-09-26 15:13:40 -04:00
sysfs.c wlcore: move sysfs handling to a separate file 2013-06-17 11:56:59 +03:00
sysfs.h wlcore: move sysfs handling to a separate file 2013-06-17 11:56:59 +03:00
testmode.c wlcore: fix interrogate command length 2013-10-23 09:47:40 +03:00
testmode.h mac80211: add vif to testmode cmd 2013-08-12 14:11:42 +02:00
tx.c wlcore: consider multiple APs when checking active_link_count 2014-02-13 15:20:16 -05:00
tx.h wlcore: send EAPOL frames with voice priority 2014-02-13 15:20:15 -05:00
wl12xx_80211.h
wlcore_i.h wl18xx: move to new firmware (wl18xx-fw-3.bin) 2014-02-13 15:20:15 -05:00
wlcore.h wlcore: wl18xx: allow CCK rates for AP mode 2014-02-13 15:20:16 -05:00