forked from Minki/linux
a8b875a549
LIRC_MODE_MODE2 and LIRC_MODE_LIRCCODE were not covered at all. Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
102 lines
2.9 KiB
ReStructuredText
102 lines
2.9 KiB
ReStructuredText
.. -*- coding: utf-8; mode: rst -*-
|
|
|
|
.. _lirc_dev_intro:
|
|
|
|
************
|
|
Introduction
|
|
************
|
|
|
|
The LIRC device interface is a bi-directional interface for transporting
|
|
raw IR data between userspace and kernelspace. Fundamentally, it is just
|
|
a chardev (/dev/lircX, for X = 0, 1, 2, ...), with a number of standard
|
|
struct file_operations defined on it. With respect to transporting raw
|
|
IR data to and fro, the essential fops are read, write and ioctl.
|
|
|
|
Example dmesg output upon a driver registering w/LIRC:
|
|
|
|
.. code-block:: none
|
|
|
|
$ dmesg |grep lirc_dev
|
|
lirc_dev: IR Remote Control driver registered, major 248
|
|
rc rc0: lirc_dev: driver ir-lirc-codec (mceusb) registered at minor = 0
|
|
|
|
What you should see for a chardev:
|
|
|
|
.. code-block:: none
|
|
|
|
$ ls -l /dev/lirc*
|
|
crw-rw---- 1 root root 248, 0 Jul 2 22:20 /dev/lirc0
|
|
|
|
.. _lirc_modes:
|
|
|
|
**********
|
|
LIRC modes
|
|
**********
|
|
|
|
LIRC supports some modes of receiving and sending IR codes, as shown
|
|
on the following table.
|
|
|
|
.. _lirc-mode-mode2:
|
|
|
|
``LIRC_MODE_MODE2``
|
|
|
|
The driver returns a sequence of pulse and space codes to userspace,
|
|
as a series of u32 values.
|
|
|
|
This mode is used only for IR receive.
|
|
|
|
The upper 8 bits determine the packet type, and the lower 24 bits
|
|
the payload. Use ``LIRC_VALUE()`` macro to get the payload, and
|
|
the macro ``LIRC_MODE2()`` will give you the type, which
|
|
is one of:
|
|
|
|
``LIRC_MODE2_PULSE``
|
|
|
|
Signifies the presence of IR in microseconds.
|
|
|
|
``LIRC_MODE2_SPACE``
|
|
|
|
Signifies absence of IR in microseconds.
|
|
|
|
``LIRC_MODE2_FREQUENCY``
|
|
|
|
If measurement of the carrier frequency was enabled with
|
|
:ref:`lirc_set_measure_carrier_mode` then this packet gives you
|
|
the carrier frequency in Hertz.
|
|
|
|
``LIRC_MODE2_TIMEOUT``
|
|
|
|
If timeout reports are enabled with
|
|
:ref:`lirc_set_rec_timeout_reports`, when the timeout set with
|
|
:ref:`lirc_set_rec_timeout` expires due to no IR being detected,
|
|
this packet will be sent, with the number of microseconds with
|
|
no IR.
|
|
|
|
.. _lirc-mode-lirccode:
|
|
|
|
``LIRC_MODE_LIRCCODE``
|
|
|
|
This mode can be used for IR receive and send.
|
|
|
|
The IR signal is decoded internally by the receiver, or encoded by the
|
|
transmitter. The LIRC interface represents the scancode as byte string,
|
|
which might not be a u32, it can be any length. The value is entirely
|
|
driver dependent. This mode is used by some older lirc drivers.
|
|
|
|
The length of each code depends on the driver, which can be retrieved
|
|
with :ref:`lirc_get_length`. This length is used both
|
|
for transmitting and receiving IR.
|
|
|
|
.. _lirc-mode-pulse:
|
|
|
|
``LIRC_MODE_PULSE``
|
|
|
|
In pulse mode, a sequence of pulse/space integer values are written to the
|
|
lirc device using :ref:`lirc-write`.
|
|
|
|
The values are alternating pulse and space lengths, in microseconds. The
|
|
first and last entry must be a pulse, so there must be an odd number
|
|
of entries.
|
|
|
|
This mode is used only for IR send.
|