1b2b1e752d
meson-gx-p23x-q20x.dtsi is currently used by five boards:
- Amlogic P230 and P231 (which should be identical, apart from the
external RGMII PHY on P230 whereas P231 can only use the internal PHY)
- Amlogic Q200 (identical to P230 but with an S912 GXM SoC instead of a
GXL S905D SoC) and Q201 (identical to P231 but with an S912 GXM SoC
instead of a GXL S905D SoC)
- NEXBOX A1 (based on the S912 GXM SoC)
The Amlogic P230 board uses a Broadcom BCM4356 SDIO wifi chip. Since the
other Amlogic reference design boards are very similar it's safe to
assume that these also use a Broadcom based SDIO wifi chip (which is
also how it was configured in meson-gx-p23x-q20x.dtsi).
However, NEXBOX A1 comes with a "longsys LTM8830" SDIO wifi module,
which is based on the "Qualcomm Atheros QCA9377-3(QCA1023-0)" chipset.
Thus move the wifi node from meson-gx-p23x-q20x.dtsi to each of the
four Amlogic reference board's .dts files.
There are no devicetree bindings for the QCA9377 SDIO wifi module yet,
so nothing is added to meson-gxm-nexbox-a1.dts.
Fixes: f51b454549 ("ARM64: dts: meson-gxm: Add support for the Nexbox A1")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
226 lines
4.2 KiB
Plaintext
226 lines
4.2 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
|
/*
|
|
* Copyright (c) 2016 Endless Computers, Inc.
|
|
* Author: Carlo Caione <carlo@endlessm.com>
|
|
*/
|
|
|
|
/* Common DTSI for same Amlogic Q200/Q201 and P230/P231 boards using either
|
|
* the pin-compatible S912 (GXM) or S905D (GXL) SoCs.
|
|
*/
|
|
|
|
/ {
|
|
aliases {
|
|
serial0 = &uart_AO;
|
|
ethernet0 = ðmac;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x0 0x0 0x80000000>;
|
|
};
|
|
|
|
hdmi_5v: regulator-hdmi-5v {
|
|
compatible = "regulator-fixed";
|
|
|
|
regulator-name = "HDMI_5V";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
|
|
gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vddio_ao18: regulator-vddio_ao18 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "VDDIO_AO18";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
|
|
vddio_boot: regulator-vddio_boot {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "VDDIO_BOOT";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
|
|
vddao_3v3: regulator-vddao_3v3 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "VDDAO_3V3";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
vcc_3v3: regulator-vcc_3v3 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "VCC_3V3";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
emmc_pwrseq: emmc-pwrseq {
|
|
compatible = "mmc-pwrseq-emmc";
|
|
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wifi32k: wifi32k {
|
|
compatible = "pwm-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <32768>;
|
|
pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
|
|
};
|
|
|
|
sdio_pwrseq: sdio-pwrseq {
|
|
compatible = "mmc-pwrseq-simple";
|
|
reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
|
|
clocks = <&wifi32k>;
|
|
clock-names = "ext_clock";
|
|
};
|
|
|
|
cvbs-connector {
|
|
compatible = "composite-video-connector";
|
|
|
|
port {
|
|
cvbs_connector_in: endpoint {
|
|
remote-endpoint = <&cvbs_vdac_out>;
|
|
};
|
|
};
|
|
};
|
|
|
|
hdmi-connector {
|
|
compatible = "hdmi-connector";
|
|
type = "a";
|
|
|
|
port {
|
|
hdmi_connector_in: endpoint {
|
|
remote-endpoint = <&hdmi_tx_tmds_out>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&cec_AO {
|
|
status = "okay";
|
|
pinctrl-0 = <&ao_cec_pins>;
|
|
pinctrl-names = "default";
|
|
hdmi-phandle = <&hdmi_tx>;
|
|
};
|
|
|
|
&cvbs_vdac_port {
|
|
cvbs_vdac_out: endpoint {
|
|
remote-endpoint = <&cvbs_connector_in>;
|
|
};
|
|
};
|
|
|
|
ðmac {
|
|
status = "okay";
|
|
};
|
|
|
|
&hdmi_tx {
|
|
status = "okay";
|
|
pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&hdmi_tx_tmds_port {
|
|
hdmi_tx_tmds_out: endpoint {
|
|
remote-endpoint = <&hdmi_connector_in>;
|
|
};
|
|
};
|
|
|
|
&ir {
|
|
status = "okay";
|
|
pinctrl-0 = <&remote_input_ao_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&pwm_ef {
|
|
status = "okay";
|
|
pinctrl-0 = <&pwm_e_pins>;
|
|
pinctrl-names = "default";
|
|
clocks = <&clkc CLKID_FCLK_DIV4>;
|
|
clock-names = "clkin0";
|
|
};
|
|
|
|
&saradc {
|
|
status = "okay";
|
|
vref-supply = <&vddio_ao18>;
|
|
};
|
|
|
|
/* Wireless SDIO Module */
|
|
&sd_emmc_a {
|
|
status = "okay";
|
|
pinctrl-0 = <&sdio_pins>;
|
|
pinctrl-1 = <&sdio_clk_gate_pins>;
|
|
pinctrl-names = "default", "clk-gate";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
bus-width = <4>;
|
|
cap-sd-highspeed;
|
|
max-frequency = <100000000>;
|
|
|
|
non-removable;
|
|
disable-wp;
|
|
|
|
mmc-pwrseq = <&sdio_pwrseq>;
|
|
|
|
vmmc-supply = <&vddao_3v3>;
|
|
vqmmc-supply = <&vddio_boot>;
|
|
};
|
|
|
|
/* SD card */
|
|
&sd_emmc_b {
|
|
status = "okay";
|
|
pinctrl-0 = <&sdcard_pins>;
|
|
pinctrl-1 = <&sdcard_clk_gate_pins>;
|
|
pinctrl-names = "default", "clk-gate";
|
|
|
|
bus-width = <4>;
|
|
cap-sd-highspeed;
|
|
max-frequency = <100000000>;
|
|
disable-wp;
|
|
|
|
cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
|
|
cd-inverted;
|
|
|
|
vmmc-supply = <&vddao_3v3>;
|
|
vqmmc-supply = <&vddio_boot>;
|
|
};
|
|
|
|
/* eMMC */
|
|
&sd_emmc_c {
|
|
status = "okay";
|
|
pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
|
|
pinctrl-1 = <&emmc_clk_gate_pins>;
|
|
pinctrl-names = "default", "clk-gate";
|
|
|
|
bus-width = <8>;
|
|
cap-mmc-highspeed;
|
|
max-frequency = <200000000>;
|
|
non-removable;
|
|
disable-wp;
|
|
mmc-ddr-1_8v;
|
|
mmc-hs200-1_8v;
|
|
|
|
mmc-pwrseq = <&emmc_pwrseq>;
|
|
vmmc-supply = <&vcc_3v3>;
|
|
vqmmc-supply = <&vddio_boot>;
|
|
};
|
|
|
|
/* This UART is brought out to the DB9 connector */
|
|
&uart_AO {
|
|
status = "okay";
|
|
pinctrl-0 = <&uart_ao_a_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&usb0 {
|
|
status = "okay";
|
|
};
|