forked from Minki/linux
82ab1eeceb
also change __devinit tag for sgiioc4.c:ioc4_ide_init() to __init Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
679 lines
19 KiB
C
679 lines
19 KiB
C
/*
|
|
* linux/drivers/ide/pci/serverworks.c Version 0.8 25 Ebr 2003
|
|
*
|
|
* Copyright (C) 1998-2000 Michel Aubry
|
|
* Copyright (C) 1998-2000 Andrzej Krzysztofowicz
|
|
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
|
|
* Portions copyright (c) 2001 Sun Microsystems
|
|
*
|
|
*
|
|
* RCC/ServerWorks IDE driver for Linux
|
|
*
|
|
* OSB4: `Open South Bridge' IDE Interface (fn 1)
|
|
* supports UDMA mode 2 (33 MB/s)
|
|
*
|
|
* CSB5: `Champion South Bridge' IDE Interface (fn 1)
|
|
* all revisions support UDMA mode 4 (66 MB/s)
|
|
* revision A2.0 and up support UDMA mode 5 (100 MB/s)
|
|
*
|
|
* *** The CSB5 does not provide ANY register ***
|
|
* *** to detect 80-conductor cable presence. ***
|
|
*
|
|
* CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
|
|
*
|
|
* HT1000: AKA BCM5785 - Hypertransport Southbridge for Opteron systems. IDE
|
|
* controller same as the CSB6. Single channel ATA100 only.
|
|
*
|
|
* Documentation:
|
|
* Available under NDA only. Errata info very hard to get.
|
|
*
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/module.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/ioport.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/hdreg.h>
|
|
#include <linux/ide.h>
|
|
#include <linux/init.h>
|
|
#include <linux/delay.h>
|
|
|
|
#include <asm/io.h>
|
|
|
|
#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
|
|
#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
|
|
|
|
/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
|
|
* can overrun their FIFOs when used with the CSB5 */
|
|
static const char *svwks_bad_ata100[] = {
|
|
"ST320011A",
|
|
"ST340016A",
|
|
"ST360021A",
|
|
"ST380021A",
|
|
NULL
|
|
};
|
|
|
|
static u8 svwks_revision = 0;
|
|
static struct pci_dev *isa_dev;
|
|
|
|
static int check_in_drive_lists (ide_drive_t *drive, const char **list)
|
|
{
|
|
while (*list)
|
|
if (!strcmp(*list++, drive->id->model))
|
|
return 1;
|
|
return 0;
|
|
}
|
|
|
|
static u8 svwks_ratemask (ide_drive_t *drive)
|
|
{
|
|
struct pci_dev *dev = HWIF(drive)->pci_dev;
|
|
u8 mode = 0;
|
|
|
|
if (!svwks_revision)
|
|
pci_read_config_byte(dev, PCI_REVISION_ID, &svwks_revision);
|
|
|
|
if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
|
|
return 2;
|
|
if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
|
|
u32 reg = 0;
|
|
if (isa_dev)
|
|
pci_read_config_dword(isa_dev, 0x64, ®);
|
|
|
|
/*
|
|
* Don't enable UDMA on disk devices for the moment
|
|
*/
|
|
if(drive->media == ide_disk)
|
|
return 0;
|
|
/* Check the OSB4 DMA33 enable bit */
|
|
return ((reg & 0x00004000) == 0x00004000) ? 1 : 0;
|
|
} else if (svwks_revision < SVWKS_CSB5_REVISION_NEW) {
|
|
return 1;
|
|
} else if (svwks_revision >= SVWKS_CSB5_REVISION_NEW) {
|
|
u8 btr = 0;
|
|
pci_read_config_byte(dev, 0x5A, &btr);
|
|
mode = btr & 0x3;
|
|
if (!eighty_ninty_three(drive))
|
|
mode = min(mode, (u8)1);
|
|
/* If someone decides to do UDMA133 on CSB5 the same
|
|
issue will bite so be inclusive */
|
|
if (mode > 2 && check_in_drive_lists(drive, svwks_bad_ata100))
|
|
mode = 2;
|
|
}
|
|
if (((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
|
|
(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) &&
|
|
(!(PCI_FUNC(dev->devfn) & 1)))
|
|
mode = 2;
|
|
return mode;
|
|
}
|
|
|
|
static u8 svwks_csb_check (struct pci_dev *dev)
|
|
{
|
|
switch (dev->device) {
|
|
case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
|
|
case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
|
|
case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
|
|
case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
|
|
return 1;
|
|
default:
|
|
break;
|
|
}
|
|
return 0;
|
|
}
|
|
static int svwks_tune_chipset (ide_drive_t *drive, u8 xferspeed)
|
|
{
|
|
static const u8 udma_modes[] = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
|
|
static const u8 dma_modes[] = { 0x77, 0x21, 0x20 };
|
|
static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
|
|
static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };
|
|
static const u8 drive_pci2[] = { 0x45, 0x44, 0x47, 0x46 };
|
|
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
struct pci_dev *dev = hwif->pci_dev;
|
|
u8 speed;
|
|
u8 pio = ide_get_best_pio_mode(drive, 255, 5, NULL);
|
|
u8 unit = (drive->select.b.unit & 0x01);
|
|
u8 csb5 = svwks_csb_check(dev);
|
|
u8 ultra_enable = 0, ultra_timing = 0;
|
|
u8 dma_timing = 0, pio_timing = 0;
|
|
u16 csb5_pio = 0;
|
|
|
|
if (xferspeed == 255) /* PIO auto-tuning */
|
|
speed = XFER_PIO_0 + pio;
|
|
else
|
|
speed = ide_rate_filter(svwks_ratemask(drive), xferspeed);
|
|
|
|
/* If we are about to put a disk into UDMA mode we screwed up.
|
|
Our code assumes we never _ever_ do this on an OSB4 */
|
|
|
|
if(dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4 &&
|
|
drive->media == ide_disk && speed >= XFER_UDMA_0)
|
|
BUG();
|
|
|
|
pci_read_config_byte(dev, drive_pci[drive->dn], &pio_timing);
|
|
pci_read_config_byte(dev, drive_pci2[drive->dn], &dma_timing);
|
|
pci_read_config_byte(dev, (0x56|hwif->channel), &ultra_timing);
|
|
pci_read_config_word(dev, 0x4A, &csb5_pio);
|
|
pci_read_config_byte(dev, 0x54, &ultra_enable);
|
|
|
|
/* Per Specified Design by OEM, and ASIC Architect */
|
|
if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
|
|
(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
|
|
if (!drive->init_speed) {
|
|
u8 dma_stat = hwif->INB(hwif->dma_status);
|
|
|
|
dma_pio:
|
|
if (((ultra_enable << (7-drive->dn) & 0x80) == 0x80) &&
|
|
((dma_stat & (1<<(5+unit))) == (1<<(5+unit)))) {
|
|
drive->current_speed = drive->init_speed = XFER_UDMA_0 + udma_modes[(ultra_timing >> (4*unit)) & ~(0xF0)];
|
|
return 0;
|
|
} else if ((dma_timing) &&
|
|
((dma_stat&(1<<(5+unit)))==(1<<(5+unit)))) {
|
|
u8 dmaspeed = dma_timing;
|
|
|
|
dma_timing &= ~0xFF;
|
|
if ((dmaspeed & 0x20) == 0x20)
|
|
dmaspeed = XFER_MW_DMA_2;
|
|
else if ((dmaspeed & 0x21) == 0x21)
|
|
dmaspeed = XFER_MW_DMA_1;
|
|
else if ((dmaspeed & 0x77) == 0x77)
|
|
dmaspeed = XFER_MW_DMA_0;
|
|
else
|
|
goto dma_pio;
|
|
drive->current_speed = drive->init_speed = dmaspeed;
|
|
return 0;
|
|
} else if (pio_timing) {
|
|
u8 piospeed = pio_timing;
|
|
|
|
pio_timing &= ~0xFF;
|
|
if ((piospeed & 0x20) == 0x20)
|
|
piospeed = XFER_PIO_4;
|
|
else if ((piospeed & 0x22) == 0x22)
|
|
piospeed = XFER_PIO_3;
|
|
else if ((piospeed & 0x34) == 0x34)
|
|
piospeed = XFER_PIO_2;
|
|
else if ((piospeed & 0x47) == 0x47)
|
|
piospeed = XFER_PIO_1;
|
|
else if ((piospeed & 0x5d) == 0x5d)
|
|
piospeed = XFER_PIO_0;
|
|
else
|
|
goto oem_setup_failed;
|
|
drive->current_speed = drive->init_speed = piospeed;
|
|
return 0;
|
|
}
|
|
}
|
|
}
|
|
|
|
oem_setup_failed:
|
|
|
|
pio_timing &= ~0xFF;
|
|
dma_timing &= ~0xFF;
|
|
ultra_timing &= ~(0x0F << (4*unit));
|
|
ultra_enable &= ~(0x01 << drive->dn);
|
|
csb5_pio &= ~(0x0F << (4*drive->dn));
|
|
|
|
switch(speed) {
|
|
case XFER_PIO_4:
|
|
case XFER_PIO_3:
|
|
case XFER_PIO_2:
|
|
case XFER_PIO_1:
|
|
case XFER_PIO_0:
|
|
pio_timing |= pio_modes[speed - XFER_PIO_0];
|
|
csb5_pio |= ((speed - XFER_PIO_0) << (4*drive->dn));
|
|
break;
|
|
|
|
case XFER_MW_DMA_2:
|
|
case XFER_MW_DMA_1:
|
|
case XFER_MW_DMA_0:
|
|
pio_timing |= pio_modes[pio];
|
|
csb5_pio |= (pio << (4*drive->dn));
|
|
dma_timing |= dma_modes[speed - XFER_MW_DMA_0];
|
|
break;
|
|
|
|
case XFER_UDMA_5:
|
|
case XFER_UDMA_4:
|
|
case XFER_UDMA_3:
|
|
case XFER_UDMA_2:
|
|
case XFER_UDMA_1:
|
|
case XFER_UDMA_0:
|
|
pio_timing |= pio_modes[pio];
|
|
csb5_pio |= (pio << (4*drive->dn));
|
|
dma_timing |= dma_modes[2];
|
|
ultra_timing |= ((udma_modes[speed - XFER_UDMA_0]) << (4*unit));
|
|
ultra_enable |= (0x01 << drive->dn);
|
|
default:
|
|
break;
|
|
}
|
|
|
|
pci_write_config_byte(dev, drive_pci[drive->dn], pio_timing);
|
|
if (csb5)
|
|
pci_write_config_word(dev, 0x4A, csb5_pio);
|
|
|
|
pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
|
|
pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
|
|
pci_write_config_byte(dev, 0x54, ultra_enable);
|
|
|
|
return (ide_config_drive_speed(drive, speed));
|
|
}
|
|
|
|
static void config_chipset_for_pio (ide_drive_t *drive)
|
|
{
|
|
u16 eide_pio_timing[6] = {960, 480, 240, 180, 120, 90};
|
|
u16 xfer_pio = drive->id->eide_pio_modes;
|
|
u8 timing, speed, pio;
|
|
|
|
pio = ide_get_best_pio_mode(drive, 255, 5, NULL);
|
|
|
|
if (xfer_pio > 4)
|
|
xfer_pio = 0;
|
|
|
|
if (drive->id->eide_pio_iordy > 0)
|
|
for (xfer_pio = 5;
|
|
xfer_pio>0 &&
|
|
drive->id->eide_pio_iordy>eide_pio_timing[xfer_pio];
|
|
xfer_pio--);
|
|
else
|
|
xfer_pio = (drive->id->eide_pio_modes & 4) ? 0x05 :
|
|
(drive->id->eide_pio_modes & 2) ? 0x04 :
|
|
(drive->id->eide_pio_modes & 1) ? 0x03 :
|
|
(drive->id->tPIO & 2) ? 0x02 :
|
|
(drive->id->tPIO & 1) ? 0x01 : xfer_pio;
|
|
|
|
timing = (xfer_pio >= pio) ? xfer_pio : pio;
|
|
|
|
switch(timing) {
|
|
case 4: speed = XFER_PIO_4;break;
|
|
case 3: speed = XFER_PIO_3;break;
|
|
case 2: speed = XFER_PIO_2;break;
|
|
case 1: speed = XFER_PIO_1;break;
|
|
default:
|
|
speed = (!drive->id->tPIO) ? XFER_PIO_0 : XFER_PIO_SLOW;
|
|
break;
|
|
}
|
|
(void) svwks_tune_chipset(drive, speed);
|
|
drive->current_speed = speed;
|
|
}
|
|
|
|
static void svwks_tune_drive (ide_drive_t *drive, u8 pio)
|
|
{
|
|
if(pio == 255)
|
|
(void) svwks_tune_chipset(drive, 255);
|
|
else
|
|
(void) svwks_tune_chipset(drive, (XFER_PIO_0 + pio));
|
|
}
|
|
|
|
static int config_chipset_for_dma (ide_drive_t *drive)
|
|
{
|
|
u8 speed = ide_dma_speed(drive, svwks_ratemask(drive));
|
|
|
|
if (!(speed))
|
|
speed = XFER_PIO_0 + ide_get_best_pio_mode(drive, 255, 5, NULL);
|
|
|
|
(void) svwks_tune_chipset(drive, speed);
|
|
return ide_dma_enable(drive);
|
|
}
|
|
|
|
static int svwks_config_drive_xfer_rate (ide_drive_t *drive)
|
|
{
|
|
ide_hwif_t *hwif = HWIF(drive);
|
|
struct hd_driveid *id = drive->id;
|
|
|
|
drive->init_speed = 0;
|
|
|
|
if ((id->capability & 1) && drive->autodma) {
|
|
|
|
if (ide_use_dma(drive)) {
|
|
if (config_chipset_for_dma(drive))
|
|
return hwif->ide_dma_on(drive);
|
|
}
|
|
|
|
goto fast_ata_pio;
|
|
|
|
} else if ((id->capability & 8) || (id->field_valid & 2)) {
|
|
fast_ata_pio:
|
|
config_chipset_for_pio(drive);
|
|
// hwif->tuneproc(drive, 5);
|
|
return hwif->ide_dma_off_quietly(drive);
|
|
}
|
|
/* IORDY not supported */
|
|
return 0;
|
|
}
|
|
|
|
/* This can go soon */
|
|
|
|
static int svwks_ide_dma_end (ide_drive_t *drive)
|
|
{
|
|
return __ide_dma_end(drive);
|
|
}
|
|
|
|
static unsigned int __devinit init_chipset_svwks (struct pci_dev *dev, const char *name)
|
|
{
|
|
unsigned int reg;
|
|
u8 btr;
|
|
|
|
/* save revision id to determine DMA capability */
|
|
pci_read_config_byte(dev, PCI_REVISION_ID, &svwks_revision);
|
|
|
|
/* force Master Latency Timer value to 64 PCICLKs */
|
|
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x40);
|
|
|
|
/* OSB4 : South Bridge and IDE */
|
|
if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
|
|
isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
|
|
PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
|
|
if (isa_dev) {
|
|
pci_read_config_dword(isa_dev, 0x64, ®);
|
|
reg &= ~0x00002000; /* disable 600ns interrupt mask */
|
|
if(!(reg & 0x00004000))
|
|
printk(KERN_DEBUG "%s: UDMA not BIOS enabled.\n", name);
|
|
reg |= 0x00004000; /* enable UDMA/33 support */
|
|
pci_write_config_dword(isa_dev, 0x64, reg);
|
|
}
|
|
}
|
|
|
|
/* setup CSB5/CSB6 : South Bridge and IDE option RAID */
|
|
else if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
|
|
(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
|
|
(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
|
|
|
|
/* Third Channel Test */
|
|
if (!(PCI_FUNC(dev->devfn) & 1)) {
|
|
struct pci_dev * findev = NULL;
|
|
u32 reg4c = 0;
|
|
findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
|
|
PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
|
|
if (findev) {
|
|
pci_read_config_dword(findev, 0x4C, ®4c);
|
|
reg4c &= ~0x000007FF;
|
|
reg4c |= 0x00000040;
|
|
reg4c |= 0x00000020;
|
|
pci_write_config_dword(findev, 0x4C, reg4c);
|
|
pci_dev_put(findev);
|
|
}
|
|
outb_p(0x06, 0x0c00);
|
|
dev->irq = inb_p(0x0c01);
|
|
} else {
|
|
struct pci_dev * findev = NULL;
|
|
u8 reg41 = 0;
|
|
|
|
findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
|
|
PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
|
|
if (findev) {
|
|
pci_read_config_byte(findev, 0x41, ®41);
|
|
reg41 &= ~0x40;
|
|
pci_write_config_byte(findev, 0x41, reg41);
|
|
pci_dev_put(findev);
|
|
}
|
|
/*
|
|
* This is a device pin issue on CSB6.
|
|
* Since there will be a future raid mode,
|
|
* early versions of the chipset require the
|
|
* interrupt pin to be set, and it is a compatibility
|
|
* mode issue.
|
|
*/
|
|
if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
|
|
dev->irq = 0;
|
|
}
|
|
// pci_read_config_dword(dev, 0x40, &pioreg)
|
|
// pci_write_config_dword(dev, 0x40, 0x99999999);
|
|
// pci_read_config_dword(dev, 0x44, &dmareg);
|
|
// pci_write_config_dword(dev, 0x44, 0xFFFFFFFF);
|
|
/* setup the UDMA Control register
|
|
*
|
|
* 1. clear bit 6 to enable DMA
|
|
* 2. enable DMA modes with bits 0-1
|
|
* 00 : legacy
|
|
* 01 : udma2
|
|
* 10 : udma2/udma4
|
|
* 11 : udma2/udma4/udma5
|
|
*/
|
|
pci_read_config_byte(dev, 0x5A, &btr);
|
|
btr &= ~0x40;
|
|
if (!(PCI_FUNC(dev->devfn) & 1))
|
|
btr |= 0x2;
|
|
else
|
|
btr |= (svwks_revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
|
|
pci_write_config_byte(dev, 0x5A, btr);
|
|
}
|
|
/* Setup HT1000 SouthBridge Controller - Single Channel Only */
|
|
else if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
|
|
pci_read_config_byte(dev, 0x5A, &btr);
|
|
btr &= ~0x40;
|
|
btr |= 0x3;
|
|
pci_write_config_byte(dev, 0x5A, btr);
|
|
}
|
|
|
|
return dev->irq;
|
|
}
|
|
|
|
static unsigned int __devinit ata66_svwks_svwks (ide_hwif_t *hwif)
|
|
{
|
|
return 1;
|
|
}
|
|
|
|
/* On Dell PowerEdge servers with a CSB5/CSB6, the top two bits
|
|
* of the subsystem device ID indicate presence of an 80-pin cable.
|
|
* Bit 15 clear = secondary IDE channel does not have 80-pin cable.
|
|
* Bit 15 set = secondary IDE channel has 80-pin cable.
|
|
* Bit 14 clear = primary IDE channel does not have 80-pin cable.
|
|
* Bit 14 set = primary IDE channel has 80-pin cable.
|
|
*/
|
|
static unsigned int __devinit ata66_svwks_dell (ide_hwif_t *hwif)
|
|
{
|
|
struct pci_dev *dev = hwif->pci_dev;
|
|
if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
|
|
dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
|
|
(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE ||
|
|
dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE))
|
|
return ((1 << (hwif->channel + 14)) &
|
|
dev->subsystem_device) ? 1 : 0;
|
|
return 0;
|
|
}
|
|
|
|
/* Sun Cobalt Alpine hardware avoids the 80-pin cable
|
|
* detect issue by attaching the drives directly to the board.
|
|
* This check follows the Dell precedent (how scary is that?!)
|
|
*
|
|
* WARNING: this only works on Alpine hardware!
|
|
*/
|
|
static unsigned int __devinit ata66_svwks_cobalt (ide_hwif_t *hwif)
|
|
{
|
|
struct pci_dev *dev = hwif->pci_dev;
|
|
if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN &&
|
|
dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
|
|
dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
|
|
return ((1 << (hwif->channel + 14)) &
|
|
dev->subsystem_device) ? 1 : 0;
|
|
return 0;
|
|
}
|
|
|
|
static unsigned int __devinit ata66_svwks (ide_hwif_t *hwif)
|
|
{
|
|
struct pci_dev *dev = hwif->pci_dev;
|
|
|
|
/* Server Works */
|
|
if (dev->subsystem_vendor == PCI_VENDOR_ID_SERVERWORKS)
|
|
return ata66_svwks_svwks (hwif);
|
|
|
|
/* Dell PowerEdge */
|
|
if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL)
|
|
return ata66_svwks_dell (hwif);
|
|
|
|
/* Cobalt Alpine */
|
|
if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN)
|
|
return ata66_svwks_cobalt (hwif);
|
|
|
|
/* Per Specified Design by OEM, and ASIC Architect */
|
|
if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
|
|
(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2))
|
|
return 1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void __devinit init_hwif_svwks (ide_hwif_t *hwif)
|
|
{
|
|
u8 dma_stat = 0;
|
|
|
|
if (!hwif->irq)
|
|
hwif->irq = hwif->channel ? 15 : 14;
|
|
|
|
hwif->tuneproc = &svwks_tune_drive;
|
|
hwif->speedproc = &svwks_tune_chipset;
|
|
|
|
hwif->atapi_dma = 1;
|
|
|
|
if (hwif->pci_dev->device != PCI_DEVICE_ID_SERVERWORKS_OSB4IDE)
|
|
hwif->ultra_mask = 0x3f;
|
|
|
|
hwif->mwdma_mask = 0x07;
|
|
|
|
hwif->autodma = 0;
|
|
|
|
if (!hwif->dma_base) {
|
|
hwif->drives[0].autotune = 1;
|
|
hwif->drives[1].autotune = 1;
|
|
return;
|
|
}
|
|
|
|
hwif->ide_dma_check = &svwks_config_drive_xfer_rate;
|
|
if (hwif->pci_dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE)
|
|
hwif->ide_dma_end = &svwks_ide_dma_end;
|
|
else if (!(hwif->udma_four))
|
|
hwif->udma_four = ata66_svwks(hwif);
|
|
if (!noautodma)
|
|
hwif->autodma = 1;
|
|
|
|
dma_stat = hwif->INB(hwif->dma_status);
|
|
hwif->drives[0].autodma = (dma_stat & 0x20);
|
|
hwif->drives[1].autodma = (dma_stat & 0x40);
|
|
hwif->drives[0].autotune = (!(dma_stat & 0x20));
|
|
hwif->drives[1].autotune = (!(dma_stat & 0x40));
|
|
}
|
|
|
|
/*
|
|
* We allow the BM-DMA driver to only work on enabled interfaces.
|
|
*/
|
|
static void __devinit init_dma_svwks (ide_hwif_t *hwif, unsigned long dmabase)
|
|
{
|
|
struct pci_dev *dev = hwif->pci_dev;
|
|
|
|
if (((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
|
|
(dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) &&
|
|
(!(PCI_FUNC(dev->devfn) & 1)) && (hwif->channel))
|
|
return;
|
|
|
|
ide_setup_dma(hwif, dmabase, 8);
|
|
}
|
|
|
|
static int __devinit init_setup_svwks (struct pci_dev *dev, ide_pci_device_t *d)
|
|
{
|
|
return ide_setup_pci_device(dev, d);
|
|
}
|
|
|
|
static int __devinit init_setup_csb6 (struct pci_dev *dev, ide_pci_device_t *d)
|
|
{
|
|
if (!(PCI_FUNC(dev->devfn) & 1)) {
|
|
d->bootable = NEVER_BOARD;
|
|
if (dev->resource[0].start == 0x01f1)
|
|
d->bootable = ON_BOARD;
|
|
}
|
|
|
|
d->channels = ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE ||
|
|
dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2) &&
|
|
(!(PCI_FUNC(dev->devfn) & 1))) ? 1 : 2;
|
|
|
|
return ide_setup_pci_device(dev, d);
|
|
}
|
|
|
|
static ide_pci_device_t serverworks_chipsets[] __devinitdata = {
|
|
{ /* 0 */
|
|
.name = "SvrWks OSB4",
|
|
.init_setup = init_setup_svwks,
|
|
.init_chipset = init_chipset_svwks,
|
|
.init_hwif = init_hwif_svwks,
|
|
.channels = 2,
|
|
.autodma = AUTODMA,
|
|
.bootable = ON_BOARD,
|
|
},{ /* 1 */
|
|
.name = "SvrWks CSB5",
|
|
.init_setup = init_setup_svwks,
|
|
.init_chipset = init_chipset_svwks,
|
|
.init_hwif = init_hwif_svwks,
|
|
.init_dma = init_dma_svwks,
|
|
.channels = 2,
|
|
.autodma = AUTODMA,
|
|
.bootable = ON_BOARD,
|
|
},{ /* 2 */
|
|
.name = "SvrWks CSB6",
|
|
.init_setup = init_setup_csb6,
|
|
.init_chipset = init_chipset_svwks,
|
|
.init_hwif = init_hwif_svwks,
|
|
.init_dma = init_dma_svwks,
|
|
.channels = 2,
|
|
.autodma = AUTODMA,
|
|
.bootable = ON_BOARD,
|
|
},{ /* 3 */
|
|
.name = "SvrWks CSB6",
|
|
.init_setup = init_setup_csb6,
|
|
.init_chipset = init_chipset_svwks,
|
|
.init_hwif = init_hwif_svwks,
|
|
.init_dma = init_dma_svwks,
|
|
.channels = 1, /* 2 */
|
|
.autodma = AUTODMA,
|
|
.bootable = ON_BOARD,
|
|
},{ /* 4 */
|
|
.name = "SvrWks HT1000",
|
|
.init_setup = init_setup_svwks,
|
|
.init_chipset = init_chipset_svwks,
|
|
.init_hwif = init_hwif_svwks,
|
|
.init_dma = init_dma_svwks,
|
|
.channels = 1, /* 2 */
|
|
.autodma = AUTODMA,
|
|
.bootable = ON_BOARD,
|
|
}
|
|
};
|
|
|
|
/**
|
|
* svwks_init_one - called when a OSB/CSB is found
|
|
* @dev: the svwks device
|
|
* @id: the matching pci id
|
|
*
|
|
* Called when the PCI registration layer (or the IDE initialization)
|
|
* finds a device matching our IDE device tables.
|
|
*/
|
|
|
|
static int __devinit svwks_init_one(struct pci_dev *dev, const struct pci_device_id *id)
|
|
{
|
|
ide_pci_device_t *d = &serverworks_chipsets[id->driver_data];
|
|
|
|
return d->init_setup(dev, d);
|
|
}
|
|
|
|
static struct pci_device_id svwks_pci_tbl[] = {
|
|
{ PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
|
|
{ PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
|
|
{ PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
|
|
{ PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
|
|
{ PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
|
|
{ 0, },
|
|
};
|
|
MODULE_DEVICE_TABLE(pci, svwks_pci_tbl);
|
|
|
|
static struct pci_driver driver = {
|
|
.name = "Serverworks_IDE",
|
|
.id_table = svwks_pci_tbl,
|
|
.probe = svwks_init_one,
|
|
};
|
|
|
|
static int __init svwks_ide_init(void)
|
|
{
|
|
return ide_pci_register_driver(&driver);
|
|
}
|
|
|
|
module_init(svwks_ide_init);
|
|
|
|
MODULE_AUTHOR("Michael Aubry. Andrzej Krzysztofowicz, Andre Hedrick");
|
|
MODULE_DESCRIPTION("PCI driver module for Serverworks OSB4/CSB5/CSB6 IDE");
|
|
MODULE_LICENSE("GPL");
|