linux/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
Jorik Jonker ae0fc94152 dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
This was done to make UART1-3 on H3 consistent, and less complicated to
enable UART1-3 on the breakout header on the several H3 board (notably
Orange Pi's). This patch adds a bit of complexity for the existing Banana
Pi, which already had the RTS/CTS associated on UART1.

The RTS/CTS for UART2-3 could be defined in the same way, but since
there is no actual use case for them at the moment, they are left out.

Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-09-21 11:48:08 +03:00

196 lines
4.8 KiB
Plaintext

/*
* Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun8i-h3.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Banana Pi BPI-M2-Plus";
compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
aliases {
serial0 = &uart0;
serial1 = &uart1;
};
chosen {
stdout-path = "serial0:115200n8";
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pwr_led_bpi_m2p>;
pwr_led {
label = "bananapi-m2-plus:red:pwr";
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
default-state = "on";
};
};
gpio_keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&sw_r_bpi_m2p>;
sw4 {
label = "power";
linux,code = <BTN_0>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
};
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
pinctrl-names = "default";
pinctrl-0 = <&wifi_en_bpi_m2p>;
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
};
};
&ehci1 {
status = "okay";
};
&ehci2 {
status = "okay";
};
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
cd-inverted;
status = "okay";
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins_a>;
vmmc-supply = <&reg_vcc3v3>;
vqmmc-supply = <&reg_vcc3v3>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
brcmf: bcrmf@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&pio>;
interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
interrupt-names = "host-wake";
};
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
vmmc-supply = <&reg_vcc3v3>;
vqmmc-supply = <&reg_vcc3v3>;
bus-width = <8>;
non-removable;
status = "okay";
};
&ohci1 {
status = "okay";
};
&ohci2 {
status = "okay";
};
&r_pio {
pwr_led_bpi_m2p: led_pins@0 {
allwinner,pins = "PL10";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
sw_r_bpi_m2p: key_pins@0 {
allwinner,pins = "PL3";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
wifi_en_bpi_m2p: wifi_en_pin {
allwinner,pins = "PL7";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
status = "okay";
};
&usbphy {
/* USB VBUS is on as long as VCC-IO is on */
status = "okay";
};