forked from Minki/linux
71b149b3f7
There is no need to pinmux the UART so early in the kernel. Move it to the board init. This will also allow to finally move the gpio driver to platform device/driver. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
140 lines
3.4 KiB
C
140 lines
3.4 KiB
C
/*
|
|
* linux/arch/arm/mach-at91/board-csb637.c
|
|
*
|
|
* Copyright (C) 2005 SAN People
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/init.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/mm.h>
|
|
#include <linux/module.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/mtd/physmap.h>
|
|
|
|
#include <asm/setup.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/irq.h>
|
|
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/map.h>
|
|
#include <asm/mach/irq.h>
|
|
|
|
#include <mach/hardware.h>
|
|
#include <mach/board.h>
|
|
|
|
#include "generic.h"
|
|
|
|
|
|
static void __init csb637_init_early(void)
|
|
{
|
|
/* Initialize processor: 3.6864 MHz crystal */
|
|
at91_initialize(3686400);
|
|
}
|
|
|
|
static struct macb_platform_data __initdata csb637_eth_data = {
|
|
.phy_irq_pin = AT91_PIN_PC0,
|
|
.is_rmii = 0,
|
|
};
|
|
|
|
static struct at91_usbh_data __initdata csb637_usbh_data = {
|
|
.ports = 2,
|
|
.vbus_pin = {-EINVAL, -EINVAL},
|
|
.overcurrent_pin= {-EINVAL, -EINVAL},
|
|
};
|
|
|
|
static struct at91_udc_data __initdata csb637_udc_data = {
|
|
.vbus_pin = AT91_PIN_PB28,
|
|
.pullup_pin = AT91_PIN_PB1,
|
|
};
|
|
|
|
#define CSB_FLASH_BASE AT91_CHIPSELECT_0
|
|
#define CSB_FLASH_SIZE SZ_16M
|
|
|
|
static struct mtd_partition csb_flash_partitions[] = {
|
|
{
|
|
.name = "uMON flash",
|
|
.offset = 0,
|
|
.size = MTDPART_SIZ_FULL,
|
|
.mask_flags = MTD_WRITEABLE, /* read only */
|
|
}
|
|
};
|
|
|
|
static struct physmap_flash_data csb_flash_data = {
|
|
.width = 2,
|
|
.parts = csb_flash_partitions,
|
|
.nr_parts = ARRAY_SIZE(csb_flash_partitions),
|
|
};
|
|
|
|
static struct resource csb_flash_resources[] = {
|
|
{
|
|
.start = CSB_FLASH_BASE,
|
|
.end = CSB_FLASH_BASE + CSB_FLASH_SIZE - 1,
|
|
.flags = IORESOURCE_MEM,
|
|
}
|
|
};
|
|
|
|
static struct platform_device csb_flash = {
|
|
.name = "physmap-flash",
|
|
.id = 0,
|
|
.dev = {
|
|
.platform_data = &csb_flash_data,
|
|
},
|
|
.resource = csb_flash_resources,
|
|
.num_resources = ARRAY_SIZE(csb_flash_resources),
|
|
};
|
|
|
|
static struct gpio_led csb_leds[] = {
|
|
{ /* "d1", red */
|
|
.name = "d1",
|
|
.gpio = AT91_PIN_PB2,
|
|
.active_low = 1,
|
|
.default_trigger = "heartbeat",
|
|
},
|
|
};
|
|
|
|
static void __init csb637_board_init(void)
|
|
{
|
|
/* LED(s) */
|
|
at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds));
|
|
/* Serial */
|
|
/* DBGU on ttyS0. (Rx & Tx only) */
|
|
at91_register_uart(0, 0, 0);
|
|
at91_add_device_serial();
|
|
/* Ethernet */
|
|
at91_add_device_eth(&csb637_eth_data);
|
|
/* USB Host */
|
|
at91_add_device_usbh(&csb637_usbh_data);
|
|
/* USB Device */
|
|
at91_add_device_udc(&csb637_udc_data);
|
|
/* I2C */
|
|
at91_add_device_i2c(NULL, 0);
|
|
/* SPI */
|
|
at91_add_device_spi(NULL, 0);
|
|
/* NOR flash */
|
|
platform_device_register(&csb_flash);
|
|
}
|
|
|
|
MACHINE_START(CSB637, "Cogent CSB637")
|
|
/* Maintainer: Bill Gatliff */
|
|
.timer = &at91rm9200_timer,
|
|
.map_io = at91_map_io,
|
|
.init_early = csb637_init_early,
|
|
.init_irq = at91_init_irq_default,
|
|
.init_machine = csb637_board_init,
|
|
MACHINE_END
|