forked from Minki/linux
cd900f181a
Add support for the LTC4162-L Li-Ion battery charger. The driver allows reading back telemetry and to set some charging options like the input current limit. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
83 lines
2.3 KiB
Plaintext
83 lines
2.3 KiB
Plaintext
What: /sys/class/power_supply/ltc4162-l/charge_status
|
|
Date: Januari 2021
|
|
KernelVersion: 5.11
|
|
Description:
|
|
Detailed charge status information as reported by the chip.
|
|
|
|
Access: Read
|
|
|
|
Valid values:
|
|
ilim_reg_active
|
|
thermal_reg_active
|
|
vin_uvcl_active
|
|
iin_limit_active
|
|
constant_current
|
|
constant_voltage
|
|
charger_off
|
|
|
|
What: /sys/class/power_supply/ltc4162-l/ibat
|
|
Date: Januari 2021
|
|
KernelVersion: 5.11
|
|
Description:
|
|
Battery input current as measured by the charger. Negative value
|
|
means that the battery is discharging.
|
|
|
|
Access: Read
|
|
|
|
Valid values: Signed value in microamps
|
|
|
|
What: /sys/class/power_supply/ltc4162-l/vbat
|
|
Date: Januari 2021
|
|
KernelVersion: 5.11
|
|
Description:
|
|
Battery voltage as measured by the charger.
|
|
|
|
Access: Read
|
|
|
|
Valid values: In microvolts
|
|
|
|
What: /sys/class/power_supply/ltc4162-l/vbat_avg
|
|
Date: Januari 2021
|
|
KernelVersion: 5.11
|
|
Description:
|
|
Battery voltage, averaged over time, as measured by the charger.
|
|
|
|
Access: Read
|
|
|
|
Valid values: In microvolts
|
|
|
|
What: /sys/class/power_supply/ltc4162-l/force_telemetry
|
|
Date: Januari 2021
|
|
KernelVersion: 5.11
|
|
Description:
|
|
To save battery current, the measurement system is disabled if
|
|
the battery is the only source of power. This affects all
|
|
voltage, current and temperature measurements.
|
|
Write a "1" to this to keep performing telemetry once every few
|
|
seconds, even when running on battery (as reported by the online
|
|
property, which is "1" when external power is available and "0"
|
|
when the system runs on battery).
|
|
|
|
Access: Read, Write
|
|
|
|
Valid values: 0 (disabled) or 1 (enabled)
|
|
|
|
What: /sys/class/power_supply/ltc4162-l/arm_ship_mode
|
|
Date: Januari 2021
|
|
KernelVersion: 5.11
|
|
Description:
|
|
The charger will normally drain the battery while inactive,
|
|
typically drawing about 54 microamps. Write a "1" to this
|
|
property to arm a special "ship" mode that extends shelf life
|
|
by reducing the leakage to about 2.8 microamps. The chip will
|
|
remain in this mode (and no longer respond to I2C commands)
|
|
until some external power-supply is attached raising the input
|
|
voltage above 1V. It will then automatically revert to "0".
|
|
Writing a "0" to the property cancels the "ship" mode request.
|
|
The ship mode, when armed, activates once the input voltage
|
|
drops below 1V.
|
|
|
|
Access: Read, Write
|
|
|
|
Valid values: 0 (disable) or 1 (enable)
|