Kernel driver w83627ehf ======================= Supported chips: * Winbond W83627EHF/EHG (ISA access ONLY) Prefix: 'w83627ehf' Addresses scanned: ISA address retrieved from Super I/O registers Datasheet: http://www.nuvoton.com.tw/NR/rdonlyres/A6A258F0-F0C9-4F97-81C0-C4D29E7E943E/0/W83627EHF.pdf * Winbond W83627DHG Prefix: 'w83627dhg' Addresses scanned: ISA address retrieved from Super I/O registers Datasheet: http://www.nuvoton.com.tw/NR/rdonlyres/7885623D-A487-4CF9-A47F-30C5F73D6FE6/0/W83627DHG.pdf * Winbond W83627DHG-P Prefix: 'w83627dhg' Addresses scanned: ISA address retrieved from Super I/O registers Datasheet: not available * Winbond W83667HG Prefix: 'w83667hg' Addresses scanned: ISA address retrieved from Super I/O registers Datasheet: not available * Winbond W83667HG-B Prefix: 'w83667hg' Addresses scanned: ISA address retrieved from Super I/O registers Datasheet: Available from Nuvoton upon request Authors: Jean Delvare Yuan Mu (Winbond) Rudolf Marek David Hubbard Gong Jun Description ----------- This driver implements support for the Winbond W83627EHF, W83627EHG, W83627DHG, W83627DHG-P, W83667HG and W83667HG-B super I/O chips. We will refer to them collectively as Winbond chips. The chips implement three temperature sensors (up to four for 667HG-B), five fan rotation speed sensors, ten analog voltage sensors (only nine for the 627DHG), one VID (6 pins for the 627EHF/EHG, 8 pins for the 627DHG and 667HG), alarms with beep warnings (control unimplemented), and some automatic fan regulation strategies (plus manual fan control mode). The temperature sensor sources on W82677HG-B are configurable. temp4 is only reported if its temperature source differs from the temperature sources of the other three temperature sensors. The configured source for each of the temperature sensors is reported in tempX_label. Temperatures are measured in degrees Celsius and measurement resolution is 1 degC for temp1 and temp4, and 0.5 degC for temp2 and temp3. An alarm is triggered when the temperature gets higher than high limit; it stays on until the temperature falls below the hysteresis value. Fan rotation speeds are reported in RPM (rotations per minute). An alarm is triggered if the rotation speed has dropped below a programmable limit. Fan readings can be divided by a programmable divider (1, 2, 4, 8, 16, 32, 64 or 128) to give the readings more range or accuracy. The driver sets the most suitable fan divisor itself. Some fans might not be present because they share pins with other functions. Voltage sensors (also known as IN sensors) report their values in millivolts. An alarm is triggered if the voltage has crossed a programmable minimum or maximum limit. The driver supports automatic fan control mode known as Thermal Cruise. In this mode, the chip attempts to keep the measured temperature in a predefined temperature range. If the temperature goes out of range, fan is driven slower/faster to reach the predefined range again. The mode works for fan1-fan4. Mapping of temperatures to pwm outputs is as follows: temp1 -> pwm1 temp2 -> pwm2 temp3 -> pwm3 prog -> pwm4 (not on 667HG and 667HG-B; the programmable setting is not supported by the driver) /sys files ---------- name - this is a standard hwmon device entry. For the W83627EHF and W83627EHG, it is set to "w83627ehf", for the W83627DHG it is set to "w83627dhg", and for the W83667HG it is set to "w83667hg". pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range: 0 (stop) to 255 (full) pwm[1-4]_enable - this file controls mode of fan/temperature control: * 1 Manual mode, write to pwm file any value 0-255 (full speed) * 2 "Thermal Cruise" mode * 3 "Fan Speed Cruise" mode * 4 "Smart Fan III" mode pwm[1-4]_mode - controls if output is PWM or DC level * 0 DC output (0 - 12v) * 1 PWM output Thermal Cruise mode ------------------- If the temperature is in the range defined by: pwm[1-4]_target - set target temperature, unit millidegree Celsius (range 0 - 127000) pwm[1-4]_tolerance - tolerance, unit millidegree Celsius (range 0 - 15000) there are no changes to fan speed. Once the temperature leaves the interval, fan speed increases (temp is higher) or decreases if lower than desired. There are defined steps and times, but not exported by the driver yet. pwm[1-4]_min_output - minimum fan speed (range 1 - 255), when the temperature is below defined range. pwm[1-4]_stop_time - how many milliseconds [ms] must elapse to switch corresponding fan off. (when the temperature was below defined range). Note: last two functions are influenced by other control bits, not yet exported by the driver, so a change might not have any effect. Implementation Details ---------------------- Future driver development should bear in mind that the following registers have different functions on the 627EHF and the 627DHG. Some registers also have different power-on default values, but BIOS should already be loading appropriate defaults. Note that bank selection must be performed as is currently done in the driver for all register addresses. 0x49: only on DHG, selects temperature source for AUX fan, CPU fan0 0x4a: not completely documented for the EHF and the DHG documentation assigns different behavior to bits 7 and 6, including extending the temperature input selection to SmartFan I, not just SmartFan III. Testing on the EHF will reveal whether they are compatible or not. 0x58: Chip ID: 0xa1=EHF 0xc1=DHG 0x5e: only on DHG, has bits to enable "current mode" temperature detection and critical temperature protection 0x45b: only on EHF, bit 3, vin4 alarm (EHF supports 10 inputs, only 9 on DHG) 0x552: only on EHF, vin4 0x558: only on EHF, vin4 high limit 0x559: only on EHF, vin4 low limit 0x6b: only on DHG, SYS fan critical temperature 0x6c: only on DHG, CPU fan0 critical temperature 0x6d: only on DHG, AUX fan critical temperature 0x6e: only on DHG, CPU fan1 critical temperature 0x50-0x55 and 0x650-0x657 are marked "Test Register" for the EHF, but "Reserved Register" for the DHG The DHG also supports PECI, where the DHG queries Intel CPU temperatures, and the ICH8 southbridge gets that data via PECI from the DHG, so that the southbridge drives the fans. And the DHG supports SST, a one-wire serial bus. The DHG-P has an additional automatic fan speed control mode named Smart Fan (TM) III+. This mode is not yet supported by the driver.