I changed the string but forgot to update the fix also to
MODULE_FIRMWARE().
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Calling init to reinit ce pipe state would also
re-set all static structure links and setting
(which don't change over driver lifecycle).
Make it so alloc links structures and initializes
static data and init part to setup state
variables and clear stuff.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This was the final missing bit to making sure the
device doesn't assert interrupts to host.
This should fix possible race when target crashes
during driver teardown.
This also removes an early warm reset workaround
during pci probing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If MSI isn't configured device ROM program expects
legacy interrupts to be enabled before it can
fully boot. Don't forget to disable legacy
interrupts after that.
While at it re-use the legacy irq enabling helper
instead of calling ath10k_pci_write32().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This simply changes the source for txpower setup.
It does not make ath10k use different txpower
values for different vifs.
This will make it easier to implement chanctx in
ath10k in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using global channel won't work with chanctx. Try
to determine the channel from the information
provided in the wmi event itself alone. This
should be sufficient.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The code can be symmetrical so make it so. This
makes it easier to understand and work with.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to reconfigure peer
completely upon reassociation. This will make it
easier to have a more uniform association code
across different modes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to pass bss_conf explicitly as it
is accessible via vif pointer. This requires
slight changes in function prototypes. While at it
clean up listen interval workaround/command.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A frequent request have been to be able to provide calibration data from a
file as some of the AP devices store the calibration data on an MTD partition.
This patchset adds support for that and also makes it easier to add Device Tree
support later on.
The calibration data is found by using the id string provided by dev_name()
using this format:
cal-<bus>-<id>.bin
With PCI the id string contains bus, slot and func values. For example for a
PCI device in bus 2 slot 0, ath10k will try to retrieve a calibration data from
a file:
/lib/firmware/ath10k/cal-pci-0000:02:00.0.bin
The calibration data sequence is:
1. Check with request_firmware() if there's a calibration file
("cal-<bus>-<id>.bin") on the filesystem for this device. If yes, use that. If
not, goto 2
2. Check if otp.bin is able to successfully load the calibration data
from OTP. If yes, use that. If not, goto 3.
4. Print an error message that no calibration data found and stop driver
initialization for this device.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 3a0861fffd ("ath10k: remove ath10k_bus") removed enum ath10k_bus
because it was not used for anything at the time. But now it's needed for for
retrieving the right calibration data file so add it back. Only new addition is
ath10k_bus_str().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Based on GFP flag given to DMA coherent allocation, the behaviour of
dma_free_coherent is changed. This behavioural diffrence is noticeable
in ARM platform. If DMA memory is allocated with GFP_KERNEL, free
coherent can not be called inside spin lock. This is causing kernel
crash in ARM platforms. Fix this by changing GFP flag to atomic.
This is most likely a regression from commit 64badcb6d6 ("ath10k: workaround
fw beaconing bug").
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John W. Linville says:
====================
pull request: wireless-next 2014-10-09
Please pull this batch of fixes intended for the 3.18 stream!
Andrea Merello makes rtl818x_pci use a more reasonable transmission
rate for HW generated frames.
Fabian Frederick tweaks some kernel-doc bits to avoid warnings.
Larry Finger corrects a possible unaligned access in the rtlwifi code.
Marek Puzyniak avoids a kernel panic in ath9k_hw_reset.
Sujith Manoharan goes for the hat trick -- he fixes a smatch warning
in the shared ath code, he fixes a crash in ath9k, and he corrects
a sequence number assignment problem in ath9k too.
For ease of merging, I pulled the last bits of the wireless tree as well...
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
Two macros used to copy BSSID information use ether_addr_copy(), thus
the arrays must be 2-byte aligned. In one case, the array could become
unaligned if the struct containing it were changed. Use the __unaligned(2)
attribute to retain the necessary alignment. In addition, the magic number
used to specify the size of the array is replaced by ETH_ALEN.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, ath9k uses a global counter for all
frames that need to be assigned a sequence number.
QoS-data frames are handled properly since they
have a per-tid counter. But, beacons and other
management frames use the same counter even if
multiple interfaces or contexts are present.
Fix this issue by making the counter per-interface
and using it when mac80211 sets IEEE80211_TX_CTL_ASSIGN_SEQ.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add tracing support to forward management and data frames to
user space for packet inspection.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is required if we take into account possibility to load the driver
from initrd (RAM disk), so in other words: very early in the boot process,
before the file system is visible.
In such case we need to have the firmware files accessible from ram disk too,
and this patch guarantee this.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's not really necessary to create bssid peer for
bssid. Self-address peer is sufficient.
This prevents some firmware revisions from crashing.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It makes a lot more sense to print these kinds of
problems as a warning instead of a debug.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
hw pointer of ath_hw is not assigned to proper value
in function ath9k_hw_reset what finally causes kernel panic.
This can be solved by proper initialization of ath_hw in
ath9k_init_priv.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Acked-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a channel context is removed, the hw_queue_base
is set to -1, this will result in a panic because
ath9k_chanctx_stop_queues() can be called on an interface
that is not assigned to any context yet - for example,
when trying to scan.
Fix this issue by setting the hw_queue_base to zero
when a channel context is removed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/main.c:88 ath_printk()
error: we previously assumed 'common->hw' could be null (see line 82)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the allowed "respose rate" set (rates for HW generated frames
like ACKs) is the same as the basic rate set.
The HW will use the higher allowed response rate that is lower than the
rate of the received frame.
This is more or less what IEEE80211 mandates, but I missed the fact
that IEEE80211 also says that whenever it happens that for a modulation
class there is no any rate in the basic rates set, then the response rate
set shall include also all the mandatory rates for that modulation class.
This patch adds mandatory OFDM rates to the allowed response rate set if
no OFDM rate is included in the basic rate set.
Depending by the AP, I faced cases in which this patch seems to cause a
noticeable perfomance improvement.
- With my usual test AP there is no particular perfomance difference.
- With a prism54/hostapd AP this patch causes RX thoughput increase from
about 5Mbps to about 20Mbps.
Hopefully this patch may help people that faced performance regression wrt
the old staging driver.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx info such as msdu_id, frame len, vdev id and tid are reported
to user space by tracepoint. This is useful for collecting tx
statistics.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Upon the reception of frame, the descriptor status are reported
to user space by tracepoint. This is useful for collecting rx
statistics.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is useful for collecting pktlog statistics of tx, rx
and rate information, so add tracing for the API call.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support to configure packet log filters (tx, rx, rate control)
via debugfs. To disable htt pktlog events set the filters to 0.
ex:
To enable pktlog for all filters
echo 0x1f > /sys/kernel/debug/ieee80211/phy*/ath10k/pktlog_filter
To disable pktlog
echo 0 > /sys/kernel/debug/ieee80211/phy*/ath10k/pktlog_filter
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John W. Linville says:
====================
pull request: wireless-next 2014-10-03
Please pull tihs batch of updates intended for the 3.18 stream!
For the iwlwifi bits, Emmanuel says:
"I have here a few things that depend on the latest mac80211's changes:
RRM, TPC, Quiet Period etc... Eyal keeps improving our rate control
and we have a new device ID. This last patch should probably have
gone to wireless.git, but at that stage, I preferred to send it to
-next and CC stable."
For (most of) the Atheros bits, Kalle says:
"The only new feature is testmode support from me. Ben added a new method
to crash the firmware with an assert for debug purposes. As usual, we
have lots of smaller fixes from Michal. Matteo fixed a Kconfig
dependency with debugfs. I fixed some warnings recently added to
checkpatch."
For the NFC bits, Samuel says:
"We've had major updates for TI and ST Microelectronics drivers, and a
few NCI related changes.
For TI's trf7970a driver:
- Target mode support for trf7970a
- Suspend/resume support for trf7970a
- DT properties additions to handle different quirks
- A bunch of fixes for smartphone IOP related issues
For ST Microelectronics' ST21NFCA and ST21NFCB drivers:
- ISO15693 support for st21nfcb
- checkpatch and sparse related warning fixes
- Code cleanups and a few minor fixes
Finally, Marvell added ISO15693 support to the NCI stack, together with a
couple of NCI fixes."
For the Bluetooth bits, Johan says:
"This 3.18 pull request replaces the one I did on Monday ("bluetooth-next
2014-09-22", which hasn't been pulled yet). The additions since the last
request are:
- SCO connection fix for devices not supporting eSCO
- Cleanups regarding the SCO establishment logic
- Remove unnecessary return value from logging functions
- Header compression fix for 6lowpan
- Cleanups to the ieee802154/mrf24j40 driver
Here's a copy from previous request that this one replaces:
'
Here are some more patches for 3.18. They include various fixes to the
btusb HCI driver, a fix for LE SMP, as well as adding Jukka to the
MAINTAINERS file for generic 6LoWPAN (as requested by Alexander Aring).
I've held on to this pull request a bit since we were waiting for a SCO
related fix to get sorted out first. However, since the merge window is
getting closer I decided not to wait for it. If we do get the fix sorted
out there'll probably be a second small pull request later this week.
'"
And,
"Unless 3.17 gets delayed this will probably be our last -next pull request for
3.18. We've got:
- New Marvell hardware supportr
- Multicast support for 6lowpan
- Several of 6lowpan fixes & cleanups
- Fix for a (false-positive) lockdep warning in L2CAP
- Minor btusb cleanup"
On top of all that comes the usual sort of updates to ath5k, ath9k,
ath10k, brcmfmac, mwifiex, and wil6210. This time around there are
also a number of rtlwifi updates to enable some new hardware and
to reconcile the in-kernel drivers with some newer releases of the
Realtek vendor drivers. Also of note is some device tree work for
the bcma bus.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Indenting errors yielded the following static checker warnings:
drivers/net/wireless/rtlwifi/rtl8192ee/hw.c:533 rtl92ee_set_hw_reg() warn: add curly braces? (if)
drivers/net/wireless/rtlwifi/rtl8192ee/hw.c:539 rtl92ee_set_hw_reg() warn: add curly braces? (if)
An unreleased version of the static checker also reported:
drivers/net/wireless/rtlwifi/rtl8723be/trx.c:550 rtl8723be_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8188ee/trx.c:621 rtl88ee_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8192ee/trx.c:567 rtl92ee_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8821ae/trx.c:758 rtl8821ae_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:494 rtl8723e_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:315 rtl92se_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c:392 rtl92ce_rx_query_desc() warn: 'hdr' can't be NULL.
All of these are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver needs btcoexist, but Kconfig fails to select it. This omission
could cause build errors for some configurations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we are attempting to switch to a new
channel context, the TX queues are flushed, but
the mac80211 queues are not stopped and traffic
can still come down to the driver.
This patch fixes it by stopping the queues
assigned to the current context/vif before
trying to flush.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a full chip reset is done, all the queues
across all VIFs are stopped, but if MCC is enabled,
only the queues of the current context is awakened,
when we complete the reset.
This results in unfairness for the inactive context.
Since frames are queued internally in the driver if
there is a context mismatch, we can awaken all the
queues when coming out of a reset.
The VIF-specific queues are still used in flow control,
to ensure fairness when traffic is high.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used when the queues of a context
needs to be stopped.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change the ath9k_chanctx_wake_queues() API so
that we can pass the channel context that needs its
queues to be stopped.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When draining of the TX queues fails, a
full HW reset is done. ath_reset() makes sure
that the queues in mac80211 are restarted,
so there is no need to wake them up again.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_has_tx_pending() can be used to
check if there are pending frames instead
of having duplicate code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Checking for the queue depth outside of
the TX queue lock is incorrect and in this
case, is not required since it is done inside
ath9k_has_pending_frames().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to check if the current
channel context has active ACs queued up
if the TX queue is not empty.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds SD8887 support to mwifiex.
SD8887 is Marvell's 1x1 11ac solution.
The corresponding firmware image file is located at:
"mrvl/sd8887_uapsta.bin"
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds some more defitions to card specific register structure
and removes static defines for these registers.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce netdev IOCTLs, to be used by the debug tools.
Allows to read/write single dword value or
memory block, aligned to dword
Different address modes supported:
- BAR offset
- Firmware "linker" address
- target's AHB bus
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce manual FW recovery mode. It is activated if module parameter
@no_fw_recovery set to true. May be changed at runtime.
Recovery information provided by new "recovery" debugfs file. It prints:
mode = [auto|manual]
state = [idle|pending|running]
In manual mode, after FW error, recovery won't start automatically. Instead,
after notification to user space, recovery waits in "pending" state, as indicated by the
"recovery" debugfs file. User space tools may perform data collection and allow to
continue recovery by writing "run" to the "recovery" debugfs file.
Alternatively, recovery pending may be canceled by stopping network interface
i.e. 'ifconfig wlan0 down'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can allow more than 32 stations to be supported
without over-running the bitmap.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for reading firmware stats through the ethtool
API. This may be easier for applications to manipulate
compared to parsing a text based debugfs file.
kvalo: remove unneeded ifdefs, call ath10k_debug_fw_stats_request() and added
simple error handling
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add three counters related to firmware crashes or resets.
Usage:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/fw_reset_stats
fw_crash_counter 2
fw_warm_reset_counter 43
fw_cold_reset_counter 0
#
kvalo: split into it's own patch, add debugfs file and add locking
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Configuration randconfig-1412075201 gets an error because driver rtl8821ae
depends on driver btcoexist, but Kconfig does not select it.
Reported-by: Jim Davis <jim.epost@gmail.com>
Cc: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mwifiex device becomes GO, unicast traffic between client1 and GO stops
when client2 connects to GO. Reason behind this was PTK getting
overwritten by key_material command for client2 as it did not have client
mac address. So, client1 can no more decode GO's ping packets though it
responds to its broadcast packets.
This patch adds case to check for BSS_ROLE instead of bss_type to set
client mac address while configuring keys when device becomes GO.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9003, tx control and tx status are in separate descriptor rings.
Tx duration is extracted from the tx control descriptor data, which
ar9003_hw_proc_txdesc cannot access.
Fix getting the duration by adding a separate callback for it.
Acked-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
chan_lock is not required for checking if
we are in the middle of a HW reset, so do it
early. This also removes the small window
where the lock is dropped and reacquired.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add basic wowl (magic packet and disconnect) support. This patch adds
this support only for PCIE bus devices. This feature requires FW which
has support for wowl built in.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver gets unloaded due to error situation there is a chance
a packet gets received while fws has already been cleaned up. This
will result in kernel crash. This patch adds a check to avoid this
crash.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to provision the P2P_DEVICE mac address using p2p_da_override iovar
the discovery interface must be disabled. On some targets setting the mac
address failed so disable the discovery interface to be certain.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Msgbuf is using GFP_ATOMIC where GFP_KERNEL is also sufficient. On
some platforms the coherent DMA memory is very limited when using
GFP_ATOMIC. This patch changes usage of GFP_ATOMIC to GFP_KERNEL and
uses worker to make this possible for creation of flowring.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need a cast to assure correct value is propagated.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase driver scan timeout from 8 to 10 seconds and report results
to cfg80211. Without this patch the already received results were
dropped on driver timeout.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR934x and newer SoC devices, the layout of the AR_RTC_PLL_CONTROL
register changed. This currently breaks at least 5/10 MHz operation.
AR933x uses the old layout.
It might also have been causing other stability issues because of the
different location of the PLL_BYPASS bit which needs to be set during
PLL clock initialization.
This patch also removes more instances of hardcoded register values in
favor of properly computed ones with the PLL_BYPASS bit added.
Reported-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The cycpwr_thr1 value needs to be lower on the extension channel than on
the control channel, similar to how the register settings are programmed
in the initvals.
Also drop the unnecessary check for HT40 - this register can always be
written. This patch has been reported to improve HT40 stability and
throughput in some environments.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 09efc56345
I've received reports that this change is decreasing throughput in some
rare conditions on an AR9280 based device
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SKB lists have their own lock. So this lock is not needed.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue with rx processing function where we were
decrementing rx_pending count twice.
Patch also queues correct main_work item when rx_pending count reaches
low watermark.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A soft lockup was observed on ARM multicore platform while UDP
RX iperf was running on station.
Reason for this is delay_main_task was not taken into consideration while
jumping to process_start. Now if delay_main_task is true, we would exit
mwifiex_main_process instead of going to process_start again.
This ensure other process is scheduled on this CPU and soft lockup is avoided.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kevin Gan <ganhy@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR934x rev 3, settin the ad-hoc flag completely messes up hardware
state - beacons get stuck, almost no packets make it out, hardware is
constantly reset.
When leaving out that flag and setting up the hw like in AP mode, TSF
timers won't be automatically synced, but at least the rest works.
AR934x rev 2 and older are not affected by this bug
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a number of places, kmalloc or valloc were used to acquire memory.
To ensure that these locations are correctly initialized, the calls were
changed to kzalloc and vzalloc. The change fixes a problem that was causing
HT operations to be cancelled.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A locking problem was found in routine _rtl92ee_cmd_send_packet() that led
to system freezes. Upon inspection, several drivers had the same problem;
however, the routines all used the same code. The common code has been
moved into rtlwifi.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Realtek released new drivers on 06/28/2014. These changes implement all their
changes into the kernel version of the driver. In addition, these modifications
are part of the process of unifying the Realtek and kernel code bases.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the driver to match the latest Realtek release, and
it is an important step in getting the internal code source at Realtek to match
the code in the kernel. The primary reason for this is to make it easier for
Realtek to maintain the kernel source without requiring an intermediate like me.
In this process of merging the two source repositories, there are a lot
of changes in both, and this commit is rather large.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not only does this patch update the driver to match the latest Realtek release,
it is an important step in getting the internal code source at Realtek to match
the code in the kernel. The primary reason for this is to make it easier for
Realtek to maintain the kernel source without requiring an intermediate like me.
In this process of merging the two source repositories, there are a lot
of changes in both, and this commit is rather large.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver was entered into staging a few cycles ago because there was
not time to integrate the Realtek version into the support routines in
the kernel. Now that there is an effort to converg the code base from Linux
and the Realtek repo, it is time to move this driver. In addition, all the
updates included in the 06/28/2014 version of the Realtek drivers are
included here.
With this change, it will be necessary to delete the staging driver. That
will be handled in a separate patch. As it impacts the staging tree, such a
patch is sent to a different destination.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code fails to lock the skb queue, which leads to a number of problems.
This patch also fixes a Sparse warning about using a memset of 1 byte.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: troy_tan@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes care of missing error paths in firmware dump.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If stat data exceeds wmi-htc buffer limits
firmware splits it into many wmi stats update
events which are delivered in a ping-pong fashion
triggered by wmi stats request command.
Since there's only an implicit start-of-data and
no end-of-data indications the driver has to
perform some trickery to get complete stat data.
kvalo: use %zu to fix a compiler warning and fix a typo in a comment
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Stats were requested and processed for each read
call. This caused inconsistent readings.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The parsing function was rather complex. Simplify
by splitting it up into firmware branch specific
implementations.
While at it move the parsing code into wmi.c where
it belongs.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The return values are not used by callers of these functions
so change the functions to return void.
Other miscellanea:
o add __printf verification to wil6210 logging functions
No format/argument mismatches found
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This driver was entered into staging a few cycles ago because there was
not time to integrate the Realtek version into the support routines in
the kernel. Now that there is an effort to converg the code base from Linux
and the Realtek repo, it is time to move this driver. In addition, all the
updates included in the 06/28/2014 version of the Realtek drivers are
included here.
With this change, it will be necessary to delete the staging driver. That
will be handled in a separate patch. As it impacts the staging tree, such a
patch is sent to a different destination.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not only does this patch update the driver to match the latest Realtek release,
it is an important step in getting the internal code source at Realtek to match
the code in the kernel. The primary reason for this is to make it easier for
Realtek to maintain the kernel source without requiring an intermediate like me.
In this process of merging the two source repositories, there are a lot
of changes in both, and this commit is rather large.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Addition of the new drivers and the update to a new version for the others
lead to changes in all the core routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Realtek released a new version of the drivers on 06/28/2014. This
patch implements the new power-save code. These changes also force
corresponding changes in the drivers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each of the routines in the rtlwifi common driver needs to be modified
for the coming changes. This patch prepares core.c, but also touches other
files.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Future patches will move the drivers for RTL8192EE and RTL8821AE
from staging to the regular wireless tree. Here, the necessary features
are added to the PCI driver. Other files are touched due to changes
in the various data structs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the rtlwifi family of drivers was converted to use a workqueue when
entering or leaving power save mode (commits a269913c52, a5ffbe0a19,
41affd5286, b9116b9a2b, and 6539306b2c), the code began scheduling work from
the callback routine of a different workqueue with a resulting increase in
overhead.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The capability for 802.11ac will soon be added to these drivers. Once
that is done, a bitmask will be too large for the data storage.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clearing IEEE80211_TX_CTL_PS_RESPONSE in a frame
that is not in the current context doesn't seem right.
Instead make sure that we don't add such frames
to the UAPSD queue by using a local variable.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason why frames marked with
IEEE80211_TX_CTL_TX_OFFCHAN have to be sent using
the UAPSD queue. Since mac80211 makes sure that
RoC is done before pushing an offchannel frame
to the driver, we can use the normal TX queues
for transmission.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we use IEEE80211_HW_QUEUE_CONTROL now, the
CAB/Offchannel queues are registered as the last
two queues. There is no need to check and reassign
the queues in the TX start()/done() routines.
CAB frames will not reach the tx() callback since
we set IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING and
pull the buffered frames during beacon transmission.
We also don't have a special HW queue for handling
off-channel frames.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Two bits control TX power on BBP_R1 register. Correct the mask,
otherwise we clear additional bit on BBP_R1 register, what can have
unknown, possible negative effect.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide ethtool support; with support for interrupt coalescing through
get_coalesce/set_coalesce.
Placeholders for begin/complete will be used by runtime PM
to make sure target is powered up while performing ethtool operations
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the driver to report signal strength information
to mac80211 for rtl8187se boards.
It differs from my previous RFT patch:
http://marc.info/?l=linux-wireless&m=140155388332534&w=2
because:
- I have now a working rtl8187se card, so I could serve my RFT by myself. :)
- CCK measurement code has changed a bit, but it does basically the same things.
- OFDM measurement method is changed because the older method reported incorrect
measures, at least for signals stronger than -40dBm).
CCK measurement seems quite good. OFDM seems less accurate, but this is the
same as the "reference" staging driver dose. I wanted not to change things just
to make measures of _one_ (my) card a bit more close to what _I_ (in my setup)
expected..
IMHO results are still good enough to justify reporting signal in dBm rather than in
"unspecified" units, so this is what this patch actually does.
Results of my tests with a working rtl8187se card connected with coaxes and
various RF attenuators to my AP are:
Input (approx) | CCK meas | OFDM meas
--------------------------------------
-30dBm | -32dBm | -31dBm
-40dBm | -40dBm | -41dBm
-50dBm | -50dBm | -55dBm
-60dBm | -59dBm | -63dBm
-70dBm | -69dBm | -73dBm
-80dBm | -79dBm | -83dBm
Also some real-field tests has been done (no coax, packets in the air) for the CCK
measure method, and they resulted in reasonable values.
Thanks-to: Bernhard Schiffner <bernhard@schiffner-limbach.de> [ for real-field tests]
Signed-off-by: andrea.merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multiple channel contexts are enabled, a p2p interface
that is assigned to a context will have an address that
is different from the device mac address, which is used
by wpa_s as the p2p device ID.
Certain frames like provision requests use the device address
and these get dropped since ath9k_calculate_summary_state()
iterates over only the active interfaces in a context and the
device address is not used.
Fix this by adding the device mac address to the bssid mask.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for scan channel gap only when user_scan_in is not NULL.
user_scan_in is NULL for internal scans and if we check scan channel gap
at this place, it may result into crash.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the BSS information stored in mac80211 directly
is racy in certain conditions. For example, in a MCC
setup, if the scheduler is switching channels when
a local deauth is issued, calculation of the opmode/bssid
etc. is incorrect. To avoid this, store the bss params
in the driver and use it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville says:
====================
pull request: wireless-next 2014-09-22
Please pull this batch of updates intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
For the bluetooth bits, Johan says:
"Here are some more patches intended for 3.18. Most of them are cleanups
or fixes for SMP. The only exception is a fix for BR/EDR L2CAP fixed
channels which should now work better together with the L2CAP
information request procedure."
For the iwlwifi bits, Emmanuel says:
"I fix here dvm which was broken by my last pull request. Arik
continues to work on TDLS and Luca solved a few issues in CT-Kill. Eyal
keeps digging into rate scaling code, more to come soon. Besides this,
nothing really special here."
Beyond that, there are the usual big batches of updates to ath9k, b43,
mwifiex, and wil6210 as well as a handful of other bits here and there.
Also, rtlwifi gets some btcoexist attention from Larry.
Please let me know if there are problems!
====================
Had to adjust the wil6210 code to comply with Joe Perches's recent
change in net-next to make the netdev_*() routines return void instead
of 'int'.
Signed-off-by: David S. Miller <davem@davemloft.net>
AHB bus support was added in v2.6.38, through commit a0b907ee2a
("ath5k: Add AHB bus support."). That code can only be build if the
Kconfig symbol ATHEROS_AR231X is set. But that symbol has never been
added to the tree. So AHB bus support has always been dead code.
Let's remove all code that depends on ATHEROS_AR231X. If that symbol
ever gets added to the tree the AHB bus support can be re-added too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide calibration data used by the firmware to user space via a debugfs file.
This makes it easier to debug calibration related problems.
Example:
sudo cp /sys/kernel/debug/ieee80211/phy0/ath10k/cal_data 1.cal
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
diag_read() is used for reading from firmware memory via the diagnose window.
First user will be cal_data debugfs file.
To serialise diagnostic window access and make it safe to use while firmware is
running take ce_lock both in ath10k_pci_diag_write_mem() and
ath10k_pci_diag_read_mem(). Because of that all the CE calls had to be changed
to _nolock variants.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The diagnostic window (CE7) uses polling and is not initiliased to retrieve
interrupts so disable interrupts altogether for CE7. Otherwise ath10k crashes
when using the diagnostic window while the firmware is running due to NULL
dereference and polling reads timeout.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it easier to debug the device-target
communication at a very low level.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it easier to debug hex dumps on systems
with more than a single ath10k device.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT version is already printed so print WMI
version as well for consistency.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the brcmf_count_20mhz_channels function we are looping through a list
of channels received from firmware. Since the index of the first channel
is 0 the condition leads to an off by one bug. This is causing us to hit
the WARN_ON_ONCE(1) calls in the brcmu_d11n_decchspec function, which is
how I discovered the bug.
Introduced by:
commit b48d891676
("brcmfmac: rework wiphy structure setup")
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This gets rid of the ugly scan structure building
and uses a saner way to do it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make all wmi event functions match the same naming
style, i.e. ath10k_wmi_event_<name>.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make the phyerr structures more compact and easier
to understand. Also add constness.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The logic responsible for processing the event is
no different across different firmware binaries.
The difference that needs to be dealt with is the
ABI of data structures.
The intermediate structure uses __le32 to avoid
extra memory allocations to byteswap
variable-length substructures (i.e. host mem
chunks).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Init functions should be placed at the end of
files in most cases to avoid forward declarations
for static functions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Simplify the code by deduplicating structure
definitions and code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The structure is being set up in 2 places.
Deduplicate the code by creating a helper.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This command is not used anymore and most firmware
revisions do not seem to handle it well. Channel
switching is done via vdev restarting.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware reports the number of RF chains so use
that for initialization of supp_{tx,rx}_chainmask
instead of using a macro for 3x3 chips.
This should make tx/rx chainmask reports correct
for chips other than 3x3.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions don't wait for beacon tx
completion before sending another SWBA event. This
could lead to hardware using old (freed) beacon
data in some cases, e.g. tx credit starvation
combined with missed TBTT. This is very very rare.
On non-IOMMU-enabled hosts this could be a
possible security issue because hw could beacon
some random data on the air. On IOMMU-enabled
hosts DMAR faults would occur in most cases and
target device would crash.
Since there are no beacon tx completions (implicit
nor explicit) propagated to host the only
workaround for this is to allocate a DMA-coherent
buffer for a lifetime of a vif and use it for all
beacon tx commands. Worst case for this approach
is some beacons may become corrupted, e.g. garbled
IEs or out-of-date TIM bitmap.
Keep the original beacon-related code as-is in
case future firmware revisions solve this problem
so that the old path can be easily re-enabled with
a fw_feature flag.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ah struct might not have been initialized when
interrupt comes so check for it.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move iwl_mvm_max_scan_ie_len function to scan.c and fix the
implementation to conform with the LMAC scan API.
Since the correct implementation would leave us with unacceptably
tiny probes, add a workaround which returns a larger value.
In current implementation it's possible that unified_scan_lmac and
unified_sched_scan_lmac would return -ENOBUFS.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of traffic on multiple TIDs where one is aggregated
and the other is not RS would toggle between considering
traffic vs. the station as aggregated and not aggregated.
Instead consider the sta state as aggregated as long as
there's at least one TID aggregated.
This limitation is because the rates table is kept per
station and not per TID.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently BA notifications which don't reclaim any frames
would not cause the RS to be called as no skbs are passed
to mac80211. This is not optimal as RS can benefit from the
statistics of sent vs. acked of such a BA. This can improve the
reaction time of the RS algorithm. Also, an upcoming change in
the firmware would cause BA timeout to be reported as a BA notif
with 0 acked so this change is required for that as well.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 8000 HW series also includes the revision in the FW
name.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Align the trans->hw_rev variable format with previous series
format.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is a tradeoff between enabling better throughput for
bursty traffic and low latency. The number 6 was found to be
a good tradeoff for the Miracast use case which is the
major use case for low latency.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable RS to get updated directly via iwl_mvm_rs_tx_status
which will be called by the driver and not via mac80211
rate control. This is required for a following patch to
report on BAs which do not cause the BA window to progress.
Also this is a first step in decoupling rs from the
mac80211 rate control.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Improve the initial tx rate and antenna selection to be based on
the rssi of the last rx. This avoids starting at the lowest legacy
rate always and requiring more tx traffic to "climb" up the rates.
Since this option might cause trouble in certain setups, allow to
disable it by default.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As suggeested by checkpatch:
WARNING: Prefer ether_addr_copy() over memcpy() if the Ethernet addresses are __aligned(2)
In wmi.c I had to change due to sparse warnings copying of struct wmi_mac_addr
from form &cmd->peer_macaddr.addr to cmd->peer_macaddr.addr. In
ath10k_wmi_set_ap_ps_param() I also added the missing ".addr" to the copy
command.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Makes it more readable and fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/debug.c:593: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:594: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:595: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:596: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:597: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:599: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:600: WARNING: quoted string split across lines
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
ath10k/htc.c:49: WARNING: Possible unnecessary 'out of memory' message
ath10k/htc.c:810: WARNING: Possible unnecessary 'out of memory' message
ath10k/htt.h:1034: CHECK: Please use a blank line after function/struct/union/enum declarations
ath10k/htt_rx.c:135: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/htt_rx.c:173: CHECK: Unnecessary parentheses around htt->rx_ring.alloc_idx.vaddr
ath10k/pci.c:633: WARNING: macros should not use a trailing semicolon
ath10k/wmi.c:3594: WARNING: quoted string split across lines
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
