The scan reference wasn't released in case of offloaded scan,
causing the refcount to go wrong and prevent the device
from going into d0i3.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
STBC is enabled on HT/VHT SISO rates in case we don't care
about power consumption and it won't hurt BT.
This is done only in case the peer and our chip support STBC
of course.
While at it fixed a bug which was causing bw and ldpc
flags to be set incorrectly in the rate scale table in case
we are switching to a legacy Tx column. This had no real impact.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Scan condition iterator assumes that an interface is associated if
phy_ctxt is assigned, but this isn't the sutuation in P2P device.
OTOH P2P device is never associated so we can simply ignore it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi features a debug mechanism that allows to dump
binary data which is helpful to debug the firmware.
Until now, this data was made available for the userspace
through debugfs. For this exact purpose, devcoredump was
created. Move to the new infrastructure.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These chips support STBC in both Tx and Rx.
Given that we've added STBC Tx support enable it.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.
Add parentheses around the mask.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We used to need to include some headers in order to read the registers
and do all the calculations by ourselves, but this is not done anymore
(i.e. we let the firmware do this for us), so we don't need to include
those headers anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For WMM-AC we may have to be changing QoS parameters while the
queues are being flushed. This is not relevant in the "drop"
case, but matters when we wait for the device to finish the
transmissions.
To allow this, do the actual waiting without holding the mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The warning gives no information about the frame, and presents
the flags so that one might think they're the frame. Clarify
and add more information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It is unused and won't be available in some future invocations of the
function.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The MVM_FW_BCAST_FILTER_PASS_ALL option defined in iwl-dbg-cfg.ini
configuration file allows to enable/disable FW broadcast filtering.
If MVM_FW_BCAST_FILTER_PASS_ALL is not defined in iwl-dbg-cfg.ini or
its value is 0, the mvm broadcast filtering is enabled.
Setting MVM_FW_BCAST_FILTER_PASS_ALL=1 in iwl-dbg-cfg.ini blocks sending
of BCAST_FILTER_CMD to FW.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the new format the "CSS section" has the same TLV type
as the "mem section". So we need to run the secured flow
for all the 8000 products.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the ARC is reset when we exit from Sx in case we had
WoWLAN running, we can't access the prph before we reset
the NIC.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A few slave bus devices show better performance when we
reduce the size of the Tx A-MPDU.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Getting the BSS station vif is something that may be needed by other
parts of the code. So, instead of having an iterator specifically for
d3, change it into a generic one in utils.c. Additionally, add a
iwl_mvm_get_bss_vif() function to make it easier to retrieving it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Before we get all the chain (ie. mac80211, cfg80211, nl80211 and
userspace) changed to support net-detect, we can use this debugfs
entry for easy testing and as a proof of concept.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The net-detect feature will require a scan offload to be started in
the same way it is done now for scheduled scan. Spin a new function
off of the sched_scan_start op code for reuse. Additionally,
restructure the function a bit for more readability.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of checking if we are associated when suspending with wowlan
enabled in the interface iterator, allow it to return an unassociated
vif and move the check to the main suspend function. This will be
needed by netdetect, since it should also work when we are not
associated but the vif is active.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Take the WoWLAN handling code out of the main suspend function,
dividing it into three parts: get_config (which is used before the
firmware is switched), switch_to_d3 (which handles the rebooting of
the hardware with the D3 firmware) and config (which configures the D3
firmware for WoWLAN operation). This is necessary to prepare for the
net-detect implementation, which will use only the switch_to_d3 part
of this flow.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
mac80211 will never call rate_control_tx_status with a NULL
pointer for sta. Remove the superfluous check. This check
misled smatch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The current TLC isn't optimized for low latency and some devices
have issues with MIMO. This kind of combo creates latency issues.
Allow to temporarily disable MIMO for tests in order to solve
the latency issues without the added complexity of MIMO.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwl_poll_bit may return a strictly positive value when the
poll doesn't match on the first try.
This was caught when WoWLAN started failing upon resume
even if the poll_bit actually succeeded.
Also change a wrong print. If we reach the end of
iwl_pcie_prepare_card_hw, it means that we couldn't
get the devices.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When mac80211 wants to ensure that a frame is sent, it calls
the flush() callback. Until now, iwldvm implemented this by
waiting that all the frames are sent (ACKed or timeout).
In case of weak signal, this can take a significant amount
of time, delaying the next connection (in case of roaming).
Many users have reported that the flush would take too long
leading to the following error messages to be printed:
iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2
iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201
iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00
[snip]
iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000
[snip]
iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9]
[snip]
Instead of waiting for these packets, simply drop them. This
significantly improves the responsiveness of the network.
Note that all the queues are flushed, but the VO one. This
is not typically used by the applications and it likely
contains management frames that are useful for connection
or roaming.
This bug is tracked here:
https://bugzilla.kernel.org/show_bug.cgi?id=56581
But it is duplicated in distributions' trackers.
A simple search in Ubuntu's database led to these bugs:
https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809
Cc: <stable@vger.kernel.org>
Depends-on: 77be2c54c5 ("mac80211: add vif to flush call")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't add the time event to the list. We added it several
times the same time event, which leads to an infinite loop
when walking the list.
Since we (currently) don't support more than one ROC for STA
vif at a time, enforce this and don't add the time event
to any list.
We were also missing the locking of the mutex which led to
a lockdep splat - fix that.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The tx power should be limited from many reasons.
currently, setting the tx power is available by the mvm only for
station interface. Adding the tx power condition to
bss_info_changed_ap_ibss make it available also for AP.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
I changed the string but forgot to update the fix also to
MODULE_FIRMWARE().
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Move iwl_mvm_max_scan_ie_len function to scan.c and fix the
implementation to conform with the LMAC scan API.
Since the correct implementation would leave us with unacceptably
tiny probes, add a workaround which returns a larger value.
In current implementation it's possible that unified_scan_lmac and
unified_sched_scan_lmac would return -ENOBUFS.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of traffic on multiple TIDs where one is aggregated
and the other is not RS would toggle between considering
traffic vs. the station as aggregated and not aggregated.
Instead consider the sta state as aggregated as long as
there's at least one TID aggregated.
This limitation is because the rates table is kept per
station and not per TID.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently BA notifications which don't reclaim any frames
would not cause the RS to be called as no skbs are passed
to mac80211. This is not optimal as RS can benefit from the
statistics of sent vs. acked of such a BA. This can improve the
reaction time of the RS algorithm. Also, an upcoming change in
the firmware would cause BA timeout to be reported as a BA notif
with 0 acked so this change is required for that as well.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 8000 HW series also includes the revision in the FW
name.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Align the trans->hw_rev variable format with previous series
format.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is a tradeoff between enabling better throughput for
bursty traffic and low latency. The number 6 was found to be
a good tradeoff for the Miracast use case which is the
major use case for low latency.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable RS to get updated directly via iwl_mvm_rs_tx_status
which will be called by the driver and not via mac80211
rate control. This is required for a following patch to
report on BAs which do not cause the BA window to progress.
Also this is a first step in decoupling rs from the
mac80211 rate control.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Improve the initial tx rate and antenna selection to be based on
the rssi of the last rx. This avoids starting at the lowest legacy
rate always and requiring more tx traffic to "climb" up the rates.
Since this option might cause trouble in certain setups, allow to
disable it by default.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the past when schedule scan was started while connected on one of
interfaces FW crashes were observed. In the newest FW this issue is
solved, so remove limitaion after examining corresponding TLV flag.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When read, this new debugfs entry requests the current temperature
from the firmware and outputs it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The scheduler is a HW sub-block that directs the work of the Flow
Handler by issuing requests for frame transfers, specifying source
and destination. Its primary function is to allocate flows into the
TX FIFOs based upon a pre-determined mapping.
The driver has some responsibilities to the scheduler, namely
initialising and maintaining the hardware registers. This is
currently done by directly accessing them, which can cause races
with the firmware also accessing the registers.
To address this problem, change the driver to no longer directly
access the registers but go through the firmware for this if the
firmware has support for DQA and thus the new command.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set RRM_ENABLED (bit 6) flag in scan commands. When this flag is set
the fw will add WFA vendor-specific TPC report and DS parameter set
IEs into probe requests.
This bit is set for SCAN_OFFLOAD_REQUEST_CMD(0x51).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a ucode capability flag for support of Quiet Period (part of RRM).
If this flag is set, advertise device support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Introduce new tx command flag (TX_CMD_FLG_WRITE_TX_POWER) which requests the
fw to update the tx power value at some constant offset.
Set this flag when transmitting either TPC report or Link measurement report
action frames.
In addition, introduce new tlv which indicates whether the fw supports power
insertion (IWL_UCODE_TLV_CAPA_TXPOWER_INSERTION_SUPPORT) and publish the
corresponding nl80211 feature.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
