Add a helper function cfg80211_get_iftype_ext_capa() to
look up interface type-specific (extended) capabilities.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was missing earlier, we need to remove links when
interfaces are being destroyed, and we also need to
stop (AP) operations when a link is being destroyed.
Address these issues to remove many warnings that will
otherwise appear in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.
So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.
For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.
Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
-----BEGIN PGP SIGNATURE-----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=ccps
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
brcmfmac
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
* tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (247 commits)
mac80211: Add support to trigger sta disconnect on hardware restart
mac80211: fix potential double free on mesh join
mac80211: correct legacy rates check in ieee80211_calc_rx_airtime
nl80211: fix typo of NL80211_IF_TYPE_OCB in documentation
mac80211: Use GFP_KERNEL instead of GFP_ATOMIC when possible
mac80211: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
rtw89: 8852c: process logic efuse map
rtw89: 8852c: process efuse of phycap
rtw89: support DAV efuse reading operation
rtw89: 8852c: add chip::dle_mem
rtw89: add page_regs to handle v1 chips
rtw89: add chip_info::{h2c,c2h}_reg to support more chips
rtw89: add hci_func_en_addr to support variant generation
rtw89: add power_{on/off}_func
rtw89: read chip version depends on chip ID
rtw89: pci: use a struct to describe all registers address related to DMA channel
rtw89: pci: add V1 of PCI channel address
rtw89: pci: add struct rtw89_pci_info
rtw89: 8852c: add 8852c empty files
MAINTAINERS: add devicetree bindings entry for mt76
...
====================
Link: https://lore.kernel.org/r/20220311124029.213470-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's currently only one driver that reports CHECKSUM_COMPLETE,
that is iwlwifi. The current hardware there calculates checksum
after the SNAP header, but only RFC 1042 (and some other cases,
but replicating the exact hardware logic for corner cases in the
driver seemed awkward.)
Newer generations of hardware will checksum _including_ the SNAP,
which makes things easier.
To handle that, simply always assume the checksum _includes_ the
SNAP header, which this patch does, requiring to first add it
for older iwlwifi hardware, and then remove it again later on
conversion.
Alternatively, we could have:
1) Always assumed the checksum starts _after_ the SNAP header;
the problem with this is that we'd have to replace the exact
"what is the SNAP" check in iwlwifi that cfg80211 has.
2) Made it configurable with some flag, but that seemed like too
much complexity.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.230736e19e0e.I3e6745873585ad943c152fab9e23b5221f17a95f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the userspace tools switch from NL80211_IFTYPE_P2P_GO to
NL80211_IFTYPE_ADHOC via send_msg(NL80211_CMD_SET_INTERFACE), it
does not call the cleanup cfg80211_stop_ap(), this leads to the
initialization of in-use data. For example, this path re-init the
sdata->assigned_chanctx_list while it is still an element of
assigned_vifs list, and makes that linked list corrupt.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Reported-by: syzbot+bbf402b783eeb6d908db@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20211027173722.777287-1-phind.uet@gmail.com
Cc: stable@vger.kernel.org
Fixes: ac800140c2 ("cfg80211: .stop_ap when interface is going down")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define LC band which is a draft under IEEE 802.11bb.
Current NL80211_BAND_LC is a placeholder band and
will be more defined IEEE 802.11bb progresses.
Signed-off-by: Srinivasan Raju <srini.raju@purelifi.com>
Link: https://lore.kernel.org/r/20211018100143.7565-2-srini.raju@purelifi.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the userland switches back-and-forth between NL80211_IFTYPE_OCB and
NL80211_IFTYPE_ADHOC via send_msg(NL80211_CMD_SET_INTERFACE), there is a
chance where the cleanup cfg80211_leave_ocb() is not called. This leads
to initialization of in-use memory (e.g. init u.ibss while in-use by
u.ocb) due to a shared struct/union within ieee80211_sub_if_data:
struct ieee80211_sub_if_data {
...
union {
struct ieee80211_if_ap ap;
struct ieee80211_if_vlan vlan;
struct ieee80211_if_managed mgd;
struct ieee80211_if_ibss ibss; // <- shares address
struct ieee80211_if_mesh mesh;
struct ieee80211_if_ocb ocb; // <- shares address
struct ieee80211_if_mntr mntr;
struct ieee80211_if_nan nan;
} u;
...
}
Therefore add handling of otype == NL80211_IFTYPE_OCB, during
cfg80211_change_iface() to perform cleanup when leaving OCB mode.
link to syzkaller bug:
https://syzkaller.appspot.com/bug?id=0612dbfa595bf4b9b680ff7b4948257b8e3732d5
Reported-by: syzbot+105896fac213f26056f9@syzkaller.appspotmail.com
Signed-off-by: Du Cheng <ducheng2@gmail.com>
Link: https://lore.kernel.org/r/20210428063941.105161-1-ducheng2@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mitigate A-MSDU injection attacks (CVE-2020-24588) by detecting if the
destination address of a subframe equals an RFC1042 (i.e., LLC/SNAP)
header, and if so dropping the complete A-MSDU frame. This mitigates
known attacks, although new (unknown) aggregation-based attacks may
remain possible.
This defense works because in A-MSDU aggregation injection attacks, a
normal encrypted Wi-Fi frame is turned into an A-MSDU frame. This means
the first 6 bytes of the first A-MSDU subframe correspond to an RFC1042
header. In other words, the destination MAC address of the first A-MSDU
subframe contains the start of an RFC1042 header during an aggregation
attack. We can detect this and thereby prevent this specific attack.
For details, see Section 7.2 of "Fragment and Forge: Breaking Wi-Fi
Through Frame Aggregation and Fragmentation".
Note that for kernel 4.9 and above this patch depends on "mac80211:
properly handle A-MSDUs that start with a rfc1042 header". Otherwise
this patch has no impact and attacks will remain possible.
Cc: stable@vger.kernel.org
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20210511200110.25d93176ddaf.I9e265b597f2cd23eb44573f35b625947b386a9de@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current phyrate conversion does not include extended MCS and provides
incorrect rates. Add a flag for extended MCS in DMG and add corresponding
phyrate table for the correct conversions using base MCS in DMG specs.
Signed-off-by: Max Chen <mxchen@codeaurora.org>
Link: https://lore.kernel.org/r/1609977050-7089-2-git-send-email-mxchen@codeaurora.org
[reduce data size, make a single WARN]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Observed the warning in cfg80211_calculate_bitrate_vht() using an
11ac chip reporting MCS-11. Since devices reporting non-standard
MCS-9 is already supported add similar entries for MCS-10 and MCS-11.
Actually, the value of MCS-9@20MHz is slightly off so corrected that.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/20210105105839.3795-1-arend.vanspriel@broadcom.com
[fix array size]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
syzbot discovered a bug in which an OOB access was being made because
an unsuitable key_idx value was wrongly considered to be acceptable
while deleting a key in nl80211_del_key().
Since we don't know the cipher at the time of deletion, if
cfg80211_validate_key_settings() were to be called directly in
nl80211_del_key(), even valid keys would be wrongly determined invalid,
and deletion wouldn't occur correctly.
For this reason, a new function - cfg80211_valid_key_idx(), has been
created, to determine if the key_idx value provided is valid or not.
cfg80211_valid_key_idx() is directly called in 2 places -
nl80211_del_key(), and cfg80211_validate_key_settings().
Reported-by: syzbot+49d4cab497c2142ee170@syzkaller.appspotmail.com
Tested-by: syzbot+49d4cab497c2142ee170@syzkaller.appspotmail.com
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Link: https://lore.kernel.org/r/20201204215825.129879-1-anant.thazhemadam@gmail.com
Cc: stable@vger.kernel.org
[also disallow IGTK key IDs if no IGTK cipher is supported]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers supporting 4096-QAM rates as a vendor extension in HE mode need
to update the correct rate info to userspace while using 4096-QAM (MCS12
and MCS13) in HE mode. Add support to calculate bitrates of HE-MCS12 and
HE-MCS13 which represent the 4096-QAM modulation schemes. The MCS12 and
MCS13 bitrates are defined in IEEE P802.11be/D0.1.
In addition, scale up the bitrates by 3*2048 in order to accommodate
calculations for the new MCS12 and MCS13 rates without losing fraction
values.
Signed-off-by: Vamsi Krishna <vamsin@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20201029183457.7005-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
S1G channels have a single width defined per frequency, so
derive it from the channel flags with
ieee80211_s1g_channel_width().
Also support setting an S1G channel where control frequency may
differ from operating, and add some basic validation to
ensure the control channel is with the operating.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200908190323.15814-6-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The S1G beacon has a different header size than regular
beacons, so adjust the beacon head validator.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200908190323.15814-5-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
Adjust the 6 GHz frequency to channel conversion function,
the other way around was previously handled.
Signed-off-by: Amar Singhal <asinghal@codeaurora.org>
Link: https://lore.kernel.org/r/1592599921-10607-1-git-send-email-asinghal@codeaurora.org
[rewrite commit message, hard-code channel 2]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 6GHz band does not have regulatory approval yet, but things are
moving forward. However, that has led to a change in the channelization
of the 6GHz band which has been accepted in the 11ax specification. It
also fixes a missing MHZ_TO_KHZ() macro for 6GHz channels while at it.
This change is primarily thrown in to discuss how to deal with it.
I noticed ath11k adding 6G support with old channelization and ditto
for iw. It probably involves changes in hostapd as well.
Cc: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Cc: Jouni Malinen <jouni@w1.fi>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/edf07cdd-ad15-4012-3afd-d8b961a80b69@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some bands (S1G) define channels centered on a non-integer
MHz. Give ieee80211_channel and cfg80211_chan_def a
freq_offset component where the final frequency can be
expressed as:
MHZ_TO_KHZ(chan->center_freq) + chan->freq_offset;
Also provide some helper functions to do the frequency
conversion and test for equality.
Retain the existing interface to frequency and channel
conversion helpers, and expose new ones which handle
frequencies in units of KHz.
Some internal functions (net/wireless/chan.c) pass around
a frequency value. Convert these to units of KHz.
mesh, ibss, wext, etc. are currently ignored.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Somehow we missed this for a long time, but similar to the extended
NSS support in VHT capabilities, we need to have this in Operating
Mode notification.
Implement it by
* parsing the 160/80+80 bit there and setting the bandwidth
appropriately
* having callers of ieee80211_get_vht_max_nss() pass in the current
max NSS value as received in the operating mode notification in
order to modify it appropriately depending on the extended NSS
bits.
This updates all drivers that use it, i.e. only iwlwifi/mvm.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200326150855.098483728cfa.I4e8c25d3288441759c2793247197229f0696a37d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* lots of small documentation fixes, from Jérôme Pouiller
* beacon protection (BIGTK) support from Jouni Malinen
* some initial code for TID configuration, from Tamizh chelvam
* I reverted some new API before it's actually used, because
it's wrong to mix controlled port and preauth
* a few other cleanups/fixes
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAl5UFlsACgkQB8qZga/f
l8SwNQ//Y/dELGODumDxY03l/Bj/+XL7HYl3Yn+J8mt2mYPC3zjTjvcRJBApiAog
1Oyd75fd+EqjxDUT+ngN8uJLQ/yCVsdwfpZhwV7VanAOuLI9aYkIXnai/Qs96rj3
yDIlrBVsmfsaxf/2e9UmsLmeUSm7C5s1EzaAIwoRGvcUH0pbH9WYAXF1QV+8fmXa
yoXuHV5Bv+wOW2xWqWJsFpoV109AW24pwJm0vlILcpFP/jno2GsRvwEpnC/GJhEA
4+jfEj0KlFkOewp0/HcqrUJp4yDEBhnhTTYgDL3hSWgKRVorKqY4/QmpKQCmpVQk
Qrb6k+TrnLmKBQKdqfd+PKAEC9U/9Wjg0KLPyc9btBGFNSUG3QoDigzxxIvSlW6w
2vyanDW6780FTIi8sA7sq1cBLosIyoFG44YYwbMidVtxhBk1LMRvetNAOnAJeycp
Abbp/A2EdvzM+ZMNMRwWlsgig6WkGY7jy/zpcmQUdALM+yT2o7D5ZwxE5pa2ggds
jf0eER1vVCEpOL70swNSZbAnDNCzBzTN64GX9gQIjdVT+nMUYQXwuOgEmho1FshD
bgZz4PcaOCCSTice9GYCC3C9OqXBsE2DyBwytYYzahyDiQH13Iz6wEq/+tIIjzCN
KKRdD12TXaPobLwv5zI3kogJ1I4P1fa6RZYpkngLpMbQrQ7qiDI=
=x0rf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-24' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A new set of changes:
* lots of small documentation fixes, from Jérôme Pouiller
* beacon protection (BIGTK) support from Jouni Malinen
* some initial code for TID configuration, from Tamizh chelvam
* I reverted some new API before it's actually used, because
it's wrong to mix controlled port and preauth
* a few other cleanups/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE P802.11-REVmd/D3.0 adds support for protecting Beacon frames using
a new set of keys (BIGTK; key index 6..7) similarly to the way
group-addressed Robust Management frames are protected (IGTK; key index
4..5). Extend cfg80211 and nl80211 to allow the new BIGTK to be
configured. Add an extended feature flag to indicate driver support for
the new key index values to avoid array overflows in driver
implementations and also to indicate to user space when this
functionality is available.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-2-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Trivial cleanup, so that all bridge port-specific code can be found in
one go.
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fragments attached to a skb can be part of a compound page. In that case,
page_ref_inc will increment the refcount for the wrong page. Fix this by
using get_page instead, which calls page_ref_inc on the compound head and
also checks for overflow.
Fixes: 2b67f944f8 ("cfg80211: reuse existing page fragments in A-MSDU rx")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200113182107.20461-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch disables setting of HT20 and more for channel 14 because
the channel is only for IEEE 802.11b.
The patch for net/wireless/util.c was unit-tested.
The patch for net/wireless/chan.c was tested with iw command.
Before this patch.
$ sudo iw dev <ifname> set channel 14 HT20
$
After this patch.
$ sudo iw dev <ifname> set channel 14 HT20
kernel reports: invalid channel definition
command failed: Invalid argument (-22)
$
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Link: https://lore.kernel.org/r/20191021075045.2719-1-masashi.honma@gmail.com
[clean up the code, use != instead of equivalent >]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
-----BEGIN PGP SIGNATURE-----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=HAuT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a number of changes, but things are settling down:
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently frame registrations are not purged, even when changing the
interface type. This can lead to potentially weird situations where
frames possibly not allowed on a given interface type remain registered
due to the type switching happening after registration.
The kernel currently relies on userspace apps to actually purge the
registrations themselves, this is not something that the kernel should
rely on.
Add a call to cfg80211_mlme_purge_registrations() to forcefully remove
any registrations left over prior to switching the iftype.
Cc: stable@vger.kernel.org
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20190828211110.15005-1-denkenz@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The boundary value used for the 6G band was incorrect as it would
result in invalid 6G channel number for certain frequencies.
Reported-by: Amar Singhal <asinghal@codeaurora.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1567510772-24263-1-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the new 6GHz band the same rules apply for mandatory rates so
add it to set_mandatory_flags_band() function.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-9-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add 6GHz operating class range as defined in 802.11ax D4.1 Annex E.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-5-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the functions ieee80211_channel_to_frequency() and
ieee80211_frequency_to_channel() to support 6GHz band according
specification in 802.11ax D4.1 27.3.22.2.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-4-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix two shortcomings in the Extended Key ID API:
1) Allow the userspace to install pairwise keys using keyid 1 without
NL80211_KEY_NO_TX set. This allows the userspace to install and
activate pairwise keys with keyid 1 in the same way as for keyid 0,
simplifying the API usage for e.g. FILS and FT key installs.
2) IEEE 802.11 - 2016 restricts Extended Key ID usage to CCMP/GCMP
ciphers in IEEE 802.11 - 2016 "9.4.2.25.4 RSN capabilities".
Enforce that when installing a key.
Cc: stable@vger.kernel.org # 5.2
Fixes: 6cdd3979a2 ("nl80211/cfg80211: Extended Key ID support")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190805123400.51567-1-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
