This patch increments privatecnt value and set DMA_PRIVATE in device
caps in dma_request_slave_channel() function. This is needed to keep
privatecnt increment/decrement balance.
As function dma_release_channel() decrements privatecnt counter, we need
to increment it when channel is requested. Otherwise privatecnt drops
into negatives after few dma_release_channel() calls.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We had a regression due to reuse of descriptor so we have reverted that.
Rest are driver fixes
at_hdmac and at_xdmac for residue, trannfer width, and channel config
pl330 final fix for dma fails and overflow issue
xgene resouce map fix
mv_xor big endian op fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=X0jd
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.2-rc5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"We had a regression due to reuse of descriptor so we have reverted
that.
The rest are driver fixes:
- at_hdmac and at_xdmac for residue, trannfer width, and channel config
- pl330 final fix for dma fails and overflow issue
- xgene resouce map fix
- mv_xor big endian op fix"
* tag 'dmaengine-fix-4.2-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
Revert "dmaengine: virt-dma: don't always free descriptor upon completion"
dmaengine: mv_xor: fix big endian operation in register mode
dmaengine: xgene-dma: Fix the resource map to handle overlapping
dmaengine: at_xdmac: fix transfer data width in at_xdmac_prep_slave_sg()
dmaengine: at_hdmac: fix residue computation
dmaengine: at_xdmac: fix bug about channel configuration
dmaengine: pl330: Really fix choppy sound because of wrong residue calculation
dmaengine: pl330: Fix overflow when reporting residue in memcpy
This reverts commit b9855f03d5.
The patch break existing DMA usage case. For example, audio SOC
dmaengine never release channel and cause virt-dma to cache too
much memory in descriptor to exhaust system memory.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 6f166312c6 ("dmaengine: mv_xor: add support for a38x command
in descriptor mode") introduced the support for a feature that
appeared in Armada 38x: specifying the operation to be performed in a
per-descriptor basis rather than globally per channel.
However, when doing so, it changed the function mv_chan_set_mode() to
use:
if (IS_ENABLED(__BIG_ENDIAN))
instead of:
#if defined(__BIG_ENDIAN)
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler. Consequently, the commit broke support for big-endian,
as the XOR_DESCRIPTOR_SWAP flag was not set in the XOR channel
configuration register.
The primarily visible effect was some nasty warnings and failures
appearing during the self-test of the XOR unit:
[ 1.197368] mv_xor d0060900.xor: error on chan 0. intr cause 0x00000082
[ 1.197393] mv_xor d0060900.xor: config 0x00008440
[ 1.197410] mv_xor d0060900.xor: activation 0x00000000
[ 1.197427] mv_xor d0060900.xor: intr cause 0x00000082
[ 1.197443] mv_xor d0060900.xor: intr mask 0x000003f7
[ 1.197460] mv_xor d0060900.xor: error cause 0x00000000
[ 1.197477] mv_xor d0060900.xor: error addr 0x00000000
[ 1.197491] ------------[ cut here ]------------
[ 1.197513] WARNING: CPU: 0 PID: 1 at ../drivers/dma/mv_xor.c:664 mv_xor_interrupt_handler+0x14c/0x170()
See also:
http://storage.kernelci.org/next/next-20150617/arm-mvebu_v7_defconfig+CONFIG_CPU_BIG_ENDIAN=y/lab-khilman/boot-armada-xp-openblocks-ax3-4.txt
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 6f166312c6 ("dmaengine: mv_xor: add support for a38x command in descriptor mode")
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is an overlap in dma ring cmd csr region due to sharing of ethernet
ring cmd csr region. This patch fix the resource overlapping by mapping
the entire dma ring cmd csr region.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds the missing update of the transfer data width in
at_xdmac_prep_slave_sg().
Indeed, for each item in the scatter-gather list, we check whether the
transfer length is aligned with the data width provided by
dmaengine_slave_config(). If so, we directly use this data width for the
current part of the transfer we are preparing. Otherwise, the data width
is reduced to 8 bits (1 byte). Of course, the actual number of register
accesses must also be updated to match the new data width.
So one chunk was missing in the original patch (see Fixes tag below): the
number of register accesses was correctly set to (len >> fixed_dwidth) in
mbr_ubc but the real data width was not updated in mbr_cfg. Since mbr_cfg
may change for each part of the scatter-gather transfer this also explains
why the original patch used the Descriptor View 2 instead of the
Descriptor View 1.
Let's take the example of a DMA transfer to write 8bit data into an Atmel
USART with FIFOs. When FIFOs are enabled in the USART, its Transmit
Holding Register (THR) works in multidata mode, that is to say that up to
4 8bit data can be written into the THR in a single 32bit access and it is
still possible to write only one data with a 8bit access. To take
advantage of this new feature, the DMA driver was modified to allow
multiple dwidths when doing slave transfers.
For instance, when the total length is 22 bytes, the USART driver splits
the transfer into 2 parts:
First part: 20 bytes transferred through 5 32bit writes into THR
Second part: 2 bytes transferred though 2 8bit writes into THR
For the second part, the data width was first set to 4_BYTES by the USART
driver thanks to dmaengine_slave_config() then at_xdmac_prep_slave_sg()
reduces this data width to 1_BYTE because the 2 byte length is not aligned
with the original 4_BYTES data width. Since the data width is modified,
the actual number of writes into THR must be set accordingly.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 6d3a7d9e3a ("dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers")
Cc: stable@vger.kernel.org #4.0 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As claimed by the programmer datasheet and confirmed by the IP designer,
the Block Transfer Size (BTSIZE) bitfield of the Channel x Control A
Register (CTRLAx) always refers to a number of Source Width (SRC_WIDTH)
transfers.
Both the SRC_WIDTH and BTSIZE bitfields can be extacted from the CTRLAx
register to compute the DMA residue. So the 'tx_width' field is useless
and can be removed from the struct at_desc.
Before this patch, atc_prep_slave_sg() was not consistent: BTSIZE was
correctly initialized according to the SRC_WIDTH but 'tx_width' was always
set to reg_width, which was incorrect for MEM_TO_DEV transfers. It led to
bad DMA residue when 'tx_width' != SRC_WIDTH.
Also the 'tx_width' field was mostly set only in the first and last
descriptors. Depending on the kind of DMA transfer, this field remained
uninitialized for intermediate descriptors. The accurate DMA residue was
computed only when the currently processed descriptor was the first or the
last of the chain. This algorithm was a little bit odd. An accurate DMA
residue can always be computed using the SRC_WIDTH and BTSIZE bitfields
in the CTRLAx register.
Finally, the test to check whether the currently processed descriptor is
the last of the chain was wrong: for cyclic transfer, last_desc->lli.dscr
is NOT equal to zero, since set_desc_eol() is never called, but logically
equal to first_desc->txd.phys. This bug has a side effect on the
drivers/tty/serial/atmel_serial.c driver, which uses cyclic DMA transfer
to receive data. Since the DMA residue was wrong each time the DMA
transfer reaches the second (and last) period of the transfer, no more
data were received by the USART driver till the cyclic DMA transfer loops
back to the first period.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Torsten Fleischer <torfl6749@gmail.com>
Tested-by: Jirí Prchal <jiri.prchal@aksignal.cz>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When using descriptor view 2 or higher, we don't write the configuration
into AT_XDMAC_CC register because this configuration will be fetch from
the descriptor. Unfortunately, the PROT bit is not updated with this
method, we have to do it manually before enabling the channel.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Switch to my kernel.org alias instead of a badly named gmail address,
which I rarely use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When pl330 driver was used during sound playback, after some time or
after a number of plays the sound became choppy or totally noisy. For
example on Odroid XU3 board the first four executions of aplay with
small WAVE worked fine, but fifth was unrecognizable with errors:
$ aplay /usr/share/sounds/alsa/Front_Right.wava
underrun!!! (at least 0.095 ms long)
Issue was caused by wrong residue reported by pl330 driver to
pcm_dmaengine for its cyclic dma transfers.
The pl330_tx_status(), residue reporting function, used a "last" flag in
a descriptor to indicate that there is no more data to send.
The pl330_tx_submit() iterated over descriptors trying to remove this
flag from them and then mark last descriptor as "last". However when
iterating it actually removed the flag not from descriptors but always
from last of it (and then reset it). Thus effectively once some
descriptor was marked as last, then it stayed like this forever causing
residue to be reported too low.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Fixes: aee4d1fac8 ("dmaengine: pl330: improve pl330_tx_status() function")
Cc: <stable@vger.kernel.org>
Reported-by: gabriel@unseen.is
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During memcpy operations the residue was always set to an u32 overflowed
value.
In pl330_tx_status() function number of currently transferred bytes was
subtracted from internal "bytes_requested" field. However this
"bytes_requested" was not initialized at start to length of memcpy
buffer so transferred bytes were subtracted from 0 causing overflow.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: aee4d1fac8 ("dmaengine: pl330: improve pl330_tx_status() function")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Merge third patchbomb from Andrew Morton:
- the rest of MM
- scripts/gdb updates
- ipc/ updates
- lib/ updates
- MAINTAINERS updates
- various other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (67 commits)
genalloc: rename of_get_named_gen_pool() to of_gen_pool_get()
genalloc: rename dev_get_gen_pool() to gen_pool_get()
x86: opt into HAVE_COPY_THREAD_TLS, for both 32-bit and 64-bit
MAINTAINERS: add zpool
MAINTAINERS: BCACHE: Kent Overstreet has changed email address
MAINTAINERS: move Jens Osterkamp to CREDITS
MAINTAINERS: remove unused nbd.h pattern
MAINTAINERS: update brcm gpio filename pattern
MAINTAINERS: update brcm dts pattern
MAINTAINERS: update sound soc intel patterns
MAINTAINERS: remove website for paride
MAINTAINERS: update Emulex ocrdma email addresses
bcache: use kvfree() in various places
libcxgbi: use kvfree() in cxgbi_free_big_mem()
target: use kvfree() in session alloc and free
IB/ehca: use kvfree() in ipz_queue_{cd}tor()
drm/nouveau/gem: use kvfree() in u_free()
drm: use kvfree() in drm_free_large()
cxgb4: use kvfree() in t4_free_mem()
cxgb3: use kvfree() in cxgb_free_mem()
...
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVkgKHAAoJENkgDmzRrbjxQpwQAJVmBN6jF3SnwbQXv9vRixjH
58V33sb1G1RW+kXxQ3/e8jLX/4VaN479CufruXQp+IJWXsN/CH0lbC3k8m7u50d7
b1Zeqd/Yrh79rkc11b0X1698uGCSMlzz+V54Z0QOTEEX+nSu2ZZvccFS4UaHkn3z
rqDo00lb7rxQz8U25qro2OZrG6D3ub2q20TkWUB8EO4AOHkPn8KWP2r429Axrr0K
wlDWDTTt8/IsvPbuPf3T15RAhq1avkMXWn9nDXDjyWbpLfTn8NFnWmtesgY7Jl4t
GjbXC5WYekX3w2ZDB9KaT/DAMQ1a7RbMXNSz4RX4VbzDl+yYeSLmIh2G9fZb1PbB
PsIxrOgy4BquOWsJPm+zeFPSC3q9Cfu219L4AmxSjiZxC3dlosg5rIB892Mjoyv4
qxmg6oiqtc4Jxv+Gl9lRFVOqyHZrTC5IJ+xgfv1EyP6kKMUKLlDZtxZAuQxpUyxR
HZLq220RYnYSvkWauikq4M8fqFM8bdt6hLJnv7bVqllseROk9stCvjSiE3A9szH5
OgtOfYV5GhOeb8pCZqJKlGDw+RoJ21jtNCgOr6DgkNKV9CX/kL/Puwv8gnA0B0eh
dxCeB7f/gcLl7Cg3Z3gVVcGlgak6JWrLf5ITAJhBZ8Lv+AtL2DKmwEWS/iIMRmek
tLdh/a9GiCitqS0bT7GE
=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
To be consistent with other kernel interface namings, rename
of_get_named_gen_pool() to of_gen_pool_get(). In the original function
name "_named" suffix references to a device tree property, which contains
a phandle to a device and the corresponding device driver is assumed to
register a gen_pool object.
Due to a weak relation and to avoid any confusion (e.g. in future
possible scenario if gen_pool objects are named) the suffix is removed.
[sfr@canb.auug.org.au: crypto/marvell/cesa - fix up for of_get_named_gen_pool() rename]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This time we have support for few new devices, few new features and odd
fixes spread thru the subsystem.
New devices added
- support for CSRatlas7 dma controller
- Allwinner H3(sun8i) controller
- TI DMA crossbar driver on DRA7x
- new pxa driver
New features added:
- memset support is bought back now that we have a user in xdmac controller
- interleaved transfers support different source and destination strides
- supporting DMA routers and configuration thru DT
- support for reusing descriptors
- xdmac memset and interleaved transfer support
- hdmac support for interleaved transfers
- omap-dma support for memcpy
Others
- Constify platform_device_id
- mv_xor fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VM4w
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have support for few new devices, few new features and
odd fixes spread thru the subsystem.
New devices added:
- support for CSRatlas7 dma controller
- Allwinner H3(sun8i) controller
- TI DMA crossbar driver on DRA7x
- new pxa driver
New features added:
- memset support is bought back now that we have a user in xdmac controller
- interleaved transfers support different source and destination strides
- supporting DMA routers and configuration thru DT
- support for reusing descriptors
- xdmac memset and interleaved transfer support
- hdmac support for interleaved transfers
- omap-dma support for memcpy
Others:
- Constify platform_device_id
- mv_xor fixes and improvements"
* tag 'dmaengine-4.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: xgene: fix file permission
dmaengine: fsl-edma: clear pending interrupts on initialization
dmaengine: xdmac: Add memset support
Documentation: dmaengine: document DMA_CTRL_ACK
dmaengine: virt-dma: don't always free descriptor upon completion
dmaengine: Revert "drivers/dma: remove unused support for MEMSET operations"
dmaengine: hdmac: Implement interleaved transfers
dmaengine: Move icg helpers to global header
dmaengine: mv_xor: improve descriptors list handling and reduce locking
dmaengine: mv_xor: Enlarge descriptor pool size
dmaengine: mv_xor: add support for a38x command in descriptor mode
dmaengine: mv_xor: Rename function for consistent naming
dmaengine: mv_xor: bug fix for racing condition in descriptors cleanup
dmaengine: pl330: fix wording in mcbufsz message
dmaengine: sirf: add CSRatlas7 SoC support
dmaengine: xgene-dma: Fix "incorrect type in assignement" warnings
dmaengine: fix kernel-doc documentation
dmaengine: pxa_dma: add support for legacy transition
dmaengine: pxa_dma: add debug information
dmaengine: pxa: add pxa dmaengine driver
...
Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNoSAACgkQMUfUDdst+ymxNQCguSEmkAYNDdLyYhdcOqSxJt9u
U1gAoMThUDoomkx6CTDMU1wn53hxgMk9
=eCUS
-----END PGP SIGNATURE-----
Merge tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (152 commits)
Doc: serial-rs485.txt: update RS485 driver interface
Doc: tty.txt: remove mention of the BKL
MAINTAINERS: tty: add serial docs directory
serial: sprd: check for NULL after calling devm_clk_get
serial: 8250_pci: Correct uartclk for xr17v35x expansion chips
serial: 8250_pci: Add support for 12 port Exar boards
serial: 8250_uniphier: add bindings document for UniPhier UART
serial: core: cleanup in uart_get_baud_rate()
serial: stm32-usart: Add STM32 USART Driver
tty/serial: kill off set_irq_flags usage
tty: move linux/gsmmux.h to uapi
doc: dt: add documentation for nxp,lpc1850-uart
serial: 8250: add LPC18xx/43xx UART driver
serial: 8250_uniphier: add UniPhier serial driver
serial: 8250_dw: support ACPI platforms with integrated DMA engine
serial: of_serial: check the return value of clk_prepare_enable()
serial: of_serial: use devm_clk_get() instead of clk_get()
serial: earlycon: Add support for big-endian MMIO accesses
serial: sirf: use hrtimer for data rx
serial: sirf: correct the fifo empty_bit
...
It was a busy development cycle at this time, as you can see a wide
range of changes in diffstat. There are no big changes but many
refactoring and improvements. Here we go some highlights:
* ALSA core:
- Procfs codes were cleaned up to use seq_file
- Procfs can be opt out via Kconfig (only for EXPERT)
- Two types of jack API were unified finally; now both kctl and input
jack devs are handled via a single function call.
* HD-audio
- Continued code restructuring for the future ASoC driver; now HDA
controller driver is split to a core helper module.
- Preliminary codes for Skylake audio support in HDA core.
- Proper i915 gfx power well management for SKL & co
- Enabled runtime PM as default for Intel HDMI/DP codecs
- Newer Tegra chip supports
- More quirks for Dell headsets, Alienware (with CA0132), etc.
- A couple of DRM ELD helper API functions
* ASoC
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring
- Big refactoring, cleanup and enhancement for the Wolfson ADSP driver
- Cleanup series for TI TAS2552 and R-CAR drivers
- Fixes and improvements on RT56xx codecs
- Support for TI TAS571x power amplifiers
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs
- Support for x86 systems with RT5650 and Qualcomm Storm
- Support for Mediatek AFE (Audio Front End) unit
- Other various small fixes to ASoC codec drivers
* Firewire
- Enhanced to allow non-blocking streams to use timestamp
synchronization
- Improve support for DM1500 and BeBoBv3
* Misc
- Cleanup of old pci API functions over all PCI sound drivers
- Fix long-standing regression of the old powermac i2c setup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJVitjmAAoJEGwxgFQ9KSmksW8P/2ngNzNpo/bmmGh6xjB7GWU9
RDAkqhKd6yvcClQojGS9n4a9CJ8nk5tdqTr9rMp58N7DRv6GYCPdq0A+lLOih+yC
UPcTkTMBKm6UtvJjEcaasMxhvs5xno345oo5KrBdvlfv1rXe83dTtzEsybWYkaVD
dJbbr5QFaiyj5cTp9nanK5kyTyDDXCdP+vjBGv5u9+GbVxQ6Eenyts89uSqEZs1F
ltoBrl4VotXyqHKneJ0ttUKEimcVIgu8rCXH0sTtCg0SZVJFi+UXzI/VkkS+expL
x9bNN6bw5UT9LA8+qybFRETx+8qchFsffzeUEle4wkIpVKXt/VqjP3GIvp6umlF5
RhU5Wumf2KuIVjgVsYxd7bUkmHr4ywpqS3vSWMWU90FApJay7exatzLPyUVN0AxH
pdAizc8NWFk1kVtWq8jr9agEdxDt2l+E9UXij+ViGyouMZL1oSvOo9NgovfwvfC6
qKUisUkq53p1uPOW/U5gvF7bee2enEXMI9YUY1Z8MHx7nloq+25Nqma8P0gYthB8
6Qk+t1oqC2p7ZMSkyVHH9nySQmoLITZHZmsHqqpLW+jFtanhuckDI75AvmrScs+r
3+2YZXxPI0caZZ1qxMCd7Clmh7ZcSeRe73HXSXmF0xrLffISM3Yg3ZN10cbWQRj2
D6TiHCspLpn+pcYLcWJ2
=D78E
-----END PGP SIGNATURE-----
Merge tag 'sound-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It was a busy development cycle at this time, as you can see a wide
range of changes in diffstat. There are no big changes but many
refactoring and improvements. Here we go some highlights:
ALSA core:
- Procfs codes were cleaned up to use seq_file
- Procfs can be opt out via Kconfig (only for EXPERT)
- Two types of jack API were unified finally; now both kctl and input
jack devs are handled via a single function call.
HD-audio:
- Continued code restructuring for the future ASoC driver; now HDA
controller driver is split to a core helper module.
- Preliminary codes for Skylake audio support in HDA core.
- Proper i915 gfx power well management for SKL & co
- Enabled runtime PM as default for Intel HDMI/DP codecs
- Newer Tegra chip supports
- More quirks for Dell headsets, Alienware (with CA0132), etc.
- A couple of DRM ELD helper API functions
ASoC:
- Support for loading ASoC topology maps from firmware, intended to
be used to allow self-describing DSP firmware images to be built
which can map controls added by the DSP to userspace without the
kernel needing to know about individual DSP firmwares
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring
- Big refactoring, cleanup and enhancement for the Wolfson ADSP
driver
- Cleanup series for TI TAS2552 and R-CAR drivers
- Fixes and improvements on RT56xx codecs
- Support for TI TAS571x power amplifiers
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs
- Support for x86 systems with RT5650 and Qualcomm Storm
- Support for Mediatek AFE (Audio Front End) unit
- Other various small fixes to ASoC codec drivers
Firewire:
- Enhanced to allow non-blocking streams to use timestamp
synchronization
- Improve support for DM1500 and BeBoBv3
Misc:
- Cleanup of old pci API functions over all PCI sound drivers
- Fix long-standing regression of the old powermac i2c setup"
* tag 'sound-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (533 commits)
ALSA: pcm: Fix pcm_class sysfs output
ALSA: hda-beep: Update authors dead email address
ASoC: wm_adsp: Move DSP Rate controls into the codec
ASoC: wm8995: Fix setting sysclk for WM8995_SYSCLK_MCLK2 case
ALSA: hda: provide default bus io ops extended hdac
ALSA: hda: add hda link cleanup routine
ALSA: hda: add hdac_ext stream creation and cleanup routines
ASoC: rsrc-card: remove unused ret
ALSA: HDAC: move SND_HDA_PREALLOC_SIZE to core
ASoC: mediatek: Add machine driver for rt5650 rt5676 codec
ASoC: mediatek: Add machine driver for MAX98090 codec
ASoC: mediatek: Add AFE platform driver
ASoC: rsnd: remove io from rsnd_mod
ASoC: rsnd: move rsnd_mod_is_working() to rsnd_io_is_working()
ASoC: rsnd: don't use rsnd_mod_to_io() on snd_kcontrol
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_src_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_ssi_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_dma_xxx()
ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_get_adinr()
ASoC: rsnd: add common interrupt handler for SSI/SRC/DMA
...
Clear pending interrupts before requesting interrupts and move
interrupt initialization after channels have been initialized.
This avoids a NULL pointer dereference panic when using kexec
while DMA requests were running.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The XDMAC supports memset transfers, both over contiguous areas, and over
discontiguous areas through a LLI.
The current memset operation only supports contiguous memset for now, add some
support for it. Scatter-gathered memset will come eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVddV1AAoJECTWi3JdVIfQQQsH/RG3lgOeot5jLWMsxJSKChEl
KI+aaMcOw6Dj2LDccN8i6vUp8q44cKSXIc7lGLOzJW4K+OydCCGAvE+sJGyRE1dd
yOHwcbvjJi4zFlt01RZchJ/Wa/S6zFucl5N9HxWsV4bEtfAA59IuhJLtospUlwsA
mf9mpvSdeUAeh3lM2+AqAbXhTo6dYfD5ky5nrtpAkZjG8gqUG0u8Tpauja0lLcHi
72/3EkzKR6KHaefyPw3LdN+/H/YK79uHCVcctZnQg5xUUymcO16ReoTxKwV9cnDb
lBJ6wO8RpUAO9evoG2Yj/l4p+czDCm5VkHMq0nPklHVRh7s/2PwKfox1aw4Pumg=
=wolq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2' into asoc-next
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
# gpg: Signature made Mon 08 Jun 2015 18:48:37 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
This patch attempts to enhance the case of a transfer submitted multiple
times, and where the cost of creating the descriptors chain is not
negligible.
This happens with big video buffers (several megabytes, ie. several
thousands of linked descriptors in one scatter-gather list). In these
cases, a video driver would want to do :
- tx = dmaengine_prep_slave_sg()
- dma_engine_submit(tx);
- dma_async_issue_pending()
- wait for video completion
- read video data (or not, skipping a frame is also possible)
- dma_engine_submit(tx)
=> here, the descriptors chain recalculation will take time
=> the dma coherent allocation over and over might create holes in
the dma pool, which is counter-productive.
- dma_async_issue_pending()
- etc ...
In order to cope with this case, virt-dma is modified to prevent freeing
the descriptors upon completion if DMA_CTRL_ACK flag is set in the
transfer.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This reverts commit 48a9db462d.
Some platforms actually need support for the memset operations. Bring it back.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The AT91 HDMAC controller supports interleaved transfers through what's
called the Picture-in-Picture mode, which allows to transfer a squared
portion of a framebuffer.
This means that this interleaved transfer only supports interleaved
transfers which have a transfer size and ICGs that are fixed across all the
chunks.
While this is a quite drastic restriction of the interleaved transfers
compared to what the dmaengine API allows, this is still useful, and our
driver will only reject transfers that do not conform to this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that we can have ICGs set for both the source and destination (using
the icg field of struct data_chunk) or for only the source or the
destination (using the dst_icg or src_icg respectively), and that these
fields can be ignored depending on other parameters (src_inc, src_sgl,
etc.), the logic to get the actual ICG value can be quite tricky.
The XDMAC driver was already implementing it, but since we will need it in
other drivers, we can move it to the main header file.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some drivers implement only pause operation (no resuming). Example is
pl330 where pause is needed for getting residuum. pl330 does not support
resume operation, transfer must be stopped after pause.
However for slaves this is exposed always as "pause and resume" which
introduces subtle errors on Odroid U3 board (Exynos4412 with pl330).
After adding pause function to pl330 driver the audio playback
(utilizing DMA) gets choppy after some time (approximately 24 hours).
Fix this by exposing "cmd_pause" if and only if pause and resume are
implemented.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: gabriel@unseen.is
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: 88987d2c75 ("dmaengine: pl330: add DMA_PAUSE feature")
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch change the way free descriptors are marked.
Instead of having a field for descriptor in use, all the descriptors in the
all_slots list are free for use.
This simplify the allocation method and reduce the locking needed.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that we have 2 channels assigned to 2 CPUs and all requests are chained
on same channels, we need much more descriptors available to satisfy
async_tx workload.
3072 descriptors was found in our lab as the number of descriptors which
allow the async_tx stack to work without waiting for free descriptors on
submission of new requests.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Tested-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Marvell Armada 38x SoC introduce new features to the XOR engine,
especially the fact that the engine mode (MEMCPY/XOR/PQ/etc) can be part of
the descriptor and not set through the controller registers.
This new feature allows mixing of different commands (even PQ) on the same
channel/chain without the need to stop the engine to reconfigure the engine
mode.
Refactor the driver to be able to use that new feature on the Armada 38x,
while keeping the old behaviour on the older SoCs.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current function names isn't very consistent, and functions with the
same prefix might operate on either a channel or a descriptor, which is
kind of confusing.
Rename these functions to have a consistent and clearer naming scheme.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes a bug in the XOR driver where the cleanup function can be
called and free descriptors that never been processed by the engine (which
result in data errors).
The cleanup function will free descriptors based on the ownership bit in
the descriptors.
Fixes: ff7b04796d ("dmaengine: DMA engine driver for Marvell XOR engine")
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This fixes up a merge issue with the amba-pl011.c driver, and we want
the fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel is not trying to increase mcbufsz. It suggests you should try
doing so. Also print the calculated required size of mcbufsz.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rework slave configuration part in order to more report wrong errors
about the configuration.
Only maxburst and addr width values are checked when doing the slave
configuration. The validity of the channel configuration is done at
prepare time.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.0 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Using _bh variant for spin locks causes this kind of warning:
Starting logging: ------------[ cut here ]------------
WARNING: CPU: 0 PID: 3 at /ssd_drive/linux/kernel/softirq.c:151
__local_bh_enable_ip+0xe8/0xf4()
Modules linked in:
CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.1.0-rc2+ #94
Hardware name: Atmel SAMA5
[<c0013c04>] (unwind_backtrace) from [<c00118a4>] (show_stack+0x10/0x14)
[<c00118a4>] (show_stack) from [<c001bbcc>]
(warn_slowpath_common+0x80/0xac)
[<c001bbcc>] (warn_slowpath_common) from [<c001bc14>]
(warn_slowpath_null+0x1c/0x24)
[<c001bc14>] (warn_slowpath_null) from [<c001e28c>]
(__local_bh_enable_ip+0xe8/0xf4)
[<c001e28c>] (__local_bh_enable_ip) from [<c01fdbd0>]
(at_xdmac_device_terminate_all+0xf4/0x100)
[<c01fdbd0>] (at_xdmac_device_terminate_all) from [<c02221a4>]
(atmel_complete_tx_dma+0x34/0xf4)
[<c02221a4>] (atmel_complete_tx_dma) from [<c01fe4ac>]
(at_xdmac_tasklet+0x14c/0x1ac)
[<c01fe4ac>] (at_xdmac_tasklet) from [<c001de58>]
(tasklet_action+0x68/0xb4)
[<c001de58>] (tasklet_action) from [<c001dfdc>]
(__do_softirq+0xfc/0x238)
[<c001dfdc>] (__do_softirq) from [<c001e140>] (run_ksoftirqd+0x28/0x34)
[<c001e140>] (run_ksoftirqd) from [<c0033a3c>]
(smpboot_thread_fn+0x138/0x18c)
[<c0033a3c>] (smpboot_thread_fn) from [<c0030e7c>] (kthread+0xdc/0xf0)
[<c0030e7c>] (kthread) from [<c000f480>] (ret_from_fork+0x14/0x34)
---[ end trace b57b14a99c1d8812 ]---
It comes from the fact that devices can called some code from the DMA
controller with irq disabled. _bh variant is not intended to be used in
this case since it can enable irqs. Switch to irqsave/irqrestore variant to
avoid this situation.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.0 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
add support for new CSR atlas7 SoC. atlas7 exists V1 and V2 IP.
atlas7 DMAv1 is basically moved from marco, which has never been
delivered to customers and renamed in this patch.
atlas7 DMAv2 supports chain DMA by a chain table, this
patch also adds chain DMA support for atlas7.
atlas7 DMAv1 and DMAv2 co-exist in the same chip. there are some HW
configuration differences(register offset etc.) with old prima2 chips,
so we use compatible string to differentiate old prima2 and new atlas7,
then results in different set in HW for them.
Signed-off-by: Hao Liu <Hao.Liu@csr.com>
Signed-off-by: Yanchang Li <Yanchang.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Nothing in <asm/io.h> uses anything from <linux/vmalloc.h>, so
remove it from there and fix up the resulting build problems
triggered on x86 {64|32}-bit {def|allmod|allno}configs.
The breakages were triggering in places where x86 builds relied
on vmalloc() facilities but did not include <linux/vmalloc.h>
explicitly and relied on the implicit inclusion via <asm/io.h>.
Also add:
- <linux/init.h> to <linux/io.h>
- <asm/pgtable_types> to <asm/io.h>
... which were two other implicit header file dependencies.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[ Tidied up the changelog. ]
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Colin Cross <ccross@android.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Suma Ramars <sramars@cisco.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch fixes sparse warnings like incorrect type in assignment
(different base types), cast to restricted __le64.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The vd->node is removed from the lists when the transfer started so the
vchan_get_all_descriptors() will not find it. This results memory leak.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[andy: fix the typo to prevent a compilation error]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to achieve smooth transition of pxa drivers from old legacy dma
handling to new dmaengine, introduce a function to "hide" dma physical
channels from dmaengine.
This is temporary situation where pxa dma will be handled in 2 places :
- arch/arm/plat-pxa/dma.c
- drivers/dma/pxa_dma.c
The resources, ie. dma channels, will be controlled by pxa_dma. The
legacy code will request or release a channel with
pxad_toggle_reserved_channel().
This is not very pretty, but it ensures both legacy and dmaengine
consumers can live in the same kernel until the conversion is done.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reuse the debugging features which were available in pxa architecture.
This is a copy of the code from arch/arm/plat-pxa/dma, which is doomed
to disappear once the conversion is completed towards dmaengine.
This is a transfer of the commit "[ARM] pxa/dma: add debugfs
entries" (d294948c2c).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is a new driver for pxa SoCs, which is also compatible with the former
mmp_pdma.
The rationale behind a new driver (as opposed to incremental patching) was :
- the new driver relies on virt-dma, which obsoletes all the internal
structures of mmp_pdma (sw_desc, hw_desc, ...), and by consequence all the
functions
- mmp_pdma allocates dma coherent descriptors containing not only hardware
descriptors but linked list information
The new driver only puts the dma hardware descriptors (ie. 4 u32) into the
dma pool allocated memory. This changes completely the way descriptors are
handled
- the architecture behind the interrupt/tasklet management was rewritten to be
more conforming to virt-dma
- the buffers alignment is handled differently
The former driver assumed that the DMA channel stopped between each
descriptor. The new one chains descriptors to let the channel running. This
is a necessary guarantee for real-time high bandwidth usecases such as video
capture on "old" architectures such as pxa.
- hot chaining / cold chaining / no chaining
Whenever possible, submitting a descriptor "hot chains" it to a running
channel. There is still no guarantee that the descriptor will be issued, as
the channel might be stopped just before the descriptor is submitted. Yet
this allows to submit several video buffers, and resubmit a buffer while
another is under handling.
As before, dma_async_issue_pending() is the only guarantee to have all the
buffers issued.
When an alignment issue is detected (ie. one address in a descriptor is not
a multiple of 8), if the already running channel is in "aligned mode", the
channel will stop, and restarted in "misaligned mode" to finished the issued
list.
- descriptors reusing
A submitted, issued and completed descriptor can be reused, ie resubmitted if
it was prepared with the proper flag (DMA_PREP_ACK). Only a channel
resources release will in this case release that buffer.
This allows a rolling ring of buffers to be reused, where there are several
thousands of hardware descriptors used (video buffer for example).
Additionally, a set of more casual features is introduced :
- debugging traces
- lockless way to know if a descriptor is terminated or not
The driver was tested on zylonite board (pxa3xx) and mioa701 (pxa27x),
with dmatest, pxa_camera and pxamci.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
