Remove this device from the cxusb driver so it can be added to the dvbsky
driver.
Signed-off-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In dvb_create_media_entity(), 'dvbdev->entity' is allocated through
kzalloc(). Then, 'dvbdev->pads' is allocated through kcalloc(). However, if
kcalloc() fails, the allocated 'dvbdev->entity' is not deallocated, leading
to a memory leak bug. To fix this issue, free 'dvbdev->entity' before
returning -ENOMEM.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This protocol responds to a real philips rc-mm remote; it does not respond
to IR encoded with the encoder in ir-rcmm-decoder.c.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In cx24117_load_firmware(), 'buf' is allocated through kmalloc() to hold
the firmware. However, if i2c_transfer() fails, it is not deallocated,
leading to a memory leak bug.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In dib7000pc_detection(), 'tx' and 'rx' are allocated through kzalloc()
respectively. However, if DiB7000PC is detected, they are not deallocated,
leading to memory leaks. To fix this issue, create a label to free 'tx' and
'rx' before returning from the function.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is a simple NEC remote control device shipped with the HardKernel
ODROID range of SBC devices.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The WeTek Play 2 Android STB ships with an unusual remote where the
main up/down/left/right/enter controls are surrounded with an outer
ring of additional keys which are listed in clockwise order.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The WeTek Hub Android STB ships with a simple NEC remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Tanix TX5 max Android STB ships with a simple NEC remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Tanix TX3 mini Android STB ships with a simple NEC remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Khadas VIM and Edge SBC devices use the same NEC remote device. The
remote includes a mouse button for Android use. This has been mapped
to KEY_MUTE.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The X96-Max Android STB ships with a simple NEC remote. It includes
a TV section with preset buttons for controlling a TV. These are not
configurable, but are noted to aid visual recognition of the device.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cmd_init() to fill a struct si2168_cmd command.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
KASAN: global-out-of-bounds Read in dvb_pll_attach
Syzbot reported global-out-of-bounds Read in dvb_pll_attach, while
accessing id[dvb_pll_devcount], because dvb_pll_devcount was 65,
that is more than size of 'id' which is DVB_PLL_MAX(64).
Rather than increasing dvb_pll_devcount every time, use ida so that
numbers are allocated correctly. This does mean that no more than
64 devices can be attached at the same time, but this is more than
sufficient.
usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the
software demuxer
dvbdev: DVB: registering new adapter (774 Friio White ISDB-T USB2.0)
usb 1-1: media controller created
dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
tc90522 0-0018: Toshiba TC90522 attached.
usb 1-1: DVB: registering adapter 0 frontend 0 (Toshiba TC90522 ISDB-T
module)...
dvbdev: dvb_create_media_entity: media entity 'Toshiba TC90522 ISDB-T
module' registered.
==================================================================
BUG: KASAN: global-out-of-bounds in dvb_pll_attach+0x6c5/0x830
drivers/media/dvb-frontends/dvb-pll.c:798
Read of size 4 at addr ffffffff89c9e5e0 by task kworker/0:1/12
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.2.0-rc6+ #13
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xca/0x13e lib/dump_stack.c:113
print_address_description+0x67/0x231 mm/kasan/report.c:188
__kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317
kasan_report+0xe/0x20 mm/kasan/common.c:614
dvb_pll_attach+0x6c5/0x830 drivers/media/dvb-frontends/dvb-pll.c:798
dvb_pll_probe+0xfe/0x174 drivers/media/dvb-frontends/dvb-pll.c:877
i2c_device_probe+0x790/0xaa0 drivers/i2c/i2c-core-base.c:389
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
__device_attach+0x217/0x360 drivers/base/dd.c:843
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
device_add+0xae6/0x16f0 drivers/base/core.c:2111
i2c_new_client_device+0x5b3/0xc40 drivers/i2c/i2c-core-base.c:778
i2c_new_device+0x19/0x50 drivers/i2c/i2c-core-base.c:821
dvb_module_probe+0xf9/0x220 drivers/media/dvb-core/dvbdev.c:985
friio_tuner_attach+0x125/0x1d0 drivers/media/usb/dvb-usb-v2/gl861.c:536
dvb_usbv2_adapter_frontend_init
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:675 [inline]
dvb_usbv2_adapter_init drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:804
[inline]
dvb_usbv2_init drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:865 [inline]
dvb_usbv2_probe.cold+0x24dc/0x255d
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:980
usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
__device_attach+0x217/0x360 drivers/base/dd.c:843
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
device_add+0xae6/0x16f0 drivers/base/core.c:2111
usb_set_configuration+0xdf6/0x1670 drivers/usb/core/message.c:2023
generic_probe+0x9d/0xd5 drivers/usb/core/generic.c:210
usb_probe_device+0x99/0x100 drivers/usb/core/driver.c:266
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
__device_attach+0x217/0x360 drivers/base/dd.c:843
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
device_add+0xae6/0x16f0 drivers/base/core.c:2111
usb_new_device.cold+0x8c1/0x1016 drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x1ada/0x3590 drivers/usb/core/hub.c:5432
process_one_work+0x905/0x1570 kernel/workqueue.c:2269
process_scheduled_works kernel/workqueue.c:2331 [inline]
worker_thread+0x7ab/0xe20 kernel/workqueue.c:2417
kthread+0x30b/0x410 kernel/kthread.c:255
ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352
The buggy address belongs to the variable:
id+0x100/0x120
Memory state around the buggy address:
ffffffff89c9e480: fa fa fa fa 00 00 fa fa fa fa fa fa 00 00 00 00
ffffffff89c9e500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> ffffffff89c9e580: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
^
ffffffff89c9e600: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
ffffffff89c9e680: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
==================================================================
Reported-by: syzbot+8a8f48672560c8ca59dd@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The existing documentation was incorrect and did not correspond
to how actual codec drivers implemented this.
Update the documentation to explicitly specify what is actually
expected.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Due to complexity of the video decoding process, the V4L2 drivers of
stateful decoder hardware require specific sequences of V4L2 API calls
to be followed. These include capability enumeration, initialization,
decoding, seek, pause, dynamic resolution change, drain and end of
stream.
Specifics of the above have been discussed during Media Workshops at
LinuxCon Europe 2012 in Barcelona and then later Embedded Linux
Conference Europe 2014 in Düsseldorf. The de facto Codec API that
originated at those events was later implemented by the drivers we already
have merged in mainline, such as s5p-mfc or coda.
The only thing missing was the real specification included as a part of
Linux Media documentation. Fix it now and document the decoder part of
the Codec API.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the vicodec stateful decoder supports
dynamic resolution switching and bytestream parsing.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the mtk-vcodec decoder supports dynamic
resolution switching.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tag all the coded formats where the venus vdec supports dynamic
resolution switching.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add an enum_fmt format flag to specifically tag coded formats where
dynamic resolution switching is supported by the device.
This is useful for some codec drivers that can support dynamic
resolution switching for one or more of their listed coded formats. It
allows userspace to know whether it should extract the video parameters
itself, or if it can rely on the device to send V4L2_EVENT_SOURCE_CHANGE
when such changes are detected.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add an enum_fmt format flag to specifically tag coded formats where
full bytestream parsing is supported by the device.
Some stateful decoders are capable of fully parsing a bytestream,
but others require that userspace pre-parses the bytestream into
frames or fields (see the corresponding pixelformat descriptions
for details).
If this flag is set, then this pre-parsing step is not required
(but still possible, of course).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now that the generic bits have been added, we can activate H264 decoding
on rk3288.
Signed-off-by: Hertz Wong <hertz.wong@rock-chips.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the G1 specific bits to support H264 decoding.
Signed-off-by: Hertz Wong <hertz.wong@rock-chips.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add helpers and patch hantro_{drv,v4l2}.c to prepare addition of H264
decoding support.
Signed-off-by: Hertz Wong <hertz.wong@rock-chips.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some decoders use intra slice/frame references. The capture buffer
pointed by these references might be new and thus have invalid
timestamp which prevents the decoder logic from retrieving the
vb2_buffer object based on the output buf timestamp.
Copy all metadata (including the timestamp) before starting the decode
operation.
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The cedrus VPU is slice-based and expects V4L2_PIX_FMT_H264_SLICE
buffers to contain H264 slices with no start code.
Expose this to userspace with the newly added menu control.
These two controls are specified as mandatory for applications,
but we mark them as non-required on the driver side for
backwards compatibility.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In order to introduce other controls, the control initialization
needs to support an initial struct v4l2_ctrl_control.
While here, let's cleanup the control initialization,
removing unneeded fields.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Those lists can be extracted from the dpb, let's simplify userspace
life and build that list kernel-side (generic helpers will be provided
for drivers that need this list).
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Stateless decoders have different expectations about the
start code that is prepended on H264 slices. Add a
menu control to express the supported start code types
(including no start code).
Drivers are allowed to support only one start code type,
but they can support both too.
Note that this is independent of the H264 decoding mode,
which specifies the granularity of the decoding operations.
Either in frame-based or slice-based mode, this new control
will allow to define the start code expected on H264 slices.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some stateless decoders don't support per-slice decoding granularity
(or at least not in a way that would make them efficient or easy to use).
Expose a menu to control the supported decoding modes. Drivers are
allowed to support only one decoding but they can support both too.
To fully specify the decoding operation, we need to introduce
a start_byte_offset, to indicate where slices start.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2_PIX_FMT_H264_SLICE_RAW name was originally suggested
because the pixel format would represent H264 slices without any
start code.
However, as we will now introduce a start code menu control,
give the pixel format a more meaningful name, while it's
still early enough to do so.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Our list_sort() utility has always supported a context argument that
is passed through to the comparison routine. Now there's a use case
for the similar thing for sort().
This implements sort_r by simply extending the existing sort function
in the obvious way. To avoid code duplication, we want to implement
sort() in terms of sort_r(). The naive way to do that is
static int cmp_wrapper(const void *a, const void *b, const void *ctx)
{
int (*real_cmp)(const void*, const void*) = ctx;
return real_cmp(a, b);
}
sort(..., cmp) { sort_r(..., cmp_wrapper, cmp) }
but this would do two indirect calls for each comparison. Instead, do
as is done for the default swap functions - that only adds a cost of a
single easily predicted branch to each comparison call.
Aside from introducing support for the context argument, this also
serves as preparation for patches that will eliminate the indirect
comparison calls in common cases.
Requested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
One typo in the function name, one missing : after :c:type.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support of several sub-devices within pipeline instead
of a single one.
This allows to support a CSI-2 camera sensor connected
through a CSI-2 to parallel bridge.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add media controller support to dcmi in order
to walk within remote subdevices pipeline.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a trace of the set of supported fourcc/mbus_code which
intersect between DCMI and source sub-device.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename "subdev" entity struct field to "source"
to prepare for several subdev support.
Move asd field on top of entity struct.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some users have been having a hard time finding the hidden
menus. A typically case are camera sensor drivers
(e.g IMX219, OV5645, etc), which are common on embedded
platforms and not really "ancillary" devices.
The problem with MEDIA_SUBDRV_AUTOSELECT seems to be related
to the fact that it uses the "visible" syntax to hide
the menus.
This is not obvious and it normally takes some time to
figure out.
To fix the problem, add a comment on each of hidden menus,
which should clarify what option is causing menus to be hidden.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov5670 driver didn't get a MAINTAINERS entry when it was merged. Add
one now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
i.MX7 and i.MX6UL/L have the same CSI controller. So add i.MX6UL/L support
to imx7-media-csi driver.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Not all sensors will be able to guarantee a proper initial state.
This may be either because the driver is not properly written,
or (probably unlikely) because the hardware won't support it.
While the right solution in the former case is to fix the sensor
driver, the real world not always allows right solutions, due to lack
of available documentation and support on these sensors.
Let's relax this requirement, and allow the driver to support stream start,
even if the sensor initial sequence wasn't the expected.
Also improve the warning message to better explain the problem and provide
a hint that the sensor driver needs to be fixed.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Steve Longerbeam <slongerbeam@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a sentence that makes it more clear when the CSI-2 transmitter
must, if possible, exit LP-11 mode. That is, maintain LP-11 mode
until stream on, at which point the transmitter activates the clock
lane and transition to HS mode.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The raw Bayer formats have been listed under the label of RGB formats but
in fact they're quite different. The latter are readily usable as such
whereas the former require quite bit of image processing before useful.
Split them into RGB and raw Bayer formats.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
