For increased DPLL stability use the settings recommended in
the TRM [1] for PHY_RX registers for SATA and USB.
For SATA we need to use spread spectrum settings even
though we don't have spread spectrum enabled. The
suggested non-spread spectrum settings don't work.
[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Introduce a mode property in the driver data so that
we don't have to keep using "of_device_is_compatible()"
throughtout the driver.
No functional change.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
There seems to be a missing bit-wise or operator when setting val,
fix this by adding it in.
Fixes: 2796ceb0c1 ("phy: ti-pipe3: Update pcie phy settings")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The rockchip-emmc PHY can be configured with different
drive impedance values. Currenlty a value of 50 Ohm is
hard coded into the driver.
This patch introduces the DTS property 'drive-impedance-ohm'
for the rockchip-emmc phy node, which uses the value from the DTS
to setup the drive impedance accordingly.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phy code was using implicit sequencing between the PHY driver
and the UFS driver to implement certain hardware requirements.
Specifically, the PHY reset register in the UFS controller needs
to be deasserted before serdes start occurs in the PHY.
Before this change, the code was doing this by utilizing the two
phy callbacks, phy_init() and phy_poweron(), as "init step 1" and
"init step 2", where the UFS driver would deassert reset between
these two steps.
This makes it challenging to power off the regulators in suspend,
as regulators are initialized in init, not in poweron(), but only
poweroff() is called during suspend, not exit().
For UFS, move the actual firing up of the PHY to phy_poweron() and
phy_poweroff() callbacks, rather than init()/exit(). UFS calls
phy_poweroff() during suspend, so now all clocks and regulators for
the phy can be powered down during suspend.
QMP is a little tricky because the PHY is also shared with PCIe and
USB3, which have their own definitions for init() and poweron(). Rename
the meaty functions to _enable() and _disable() to disentangle from the
PHY core names, and then create two different ops structures: one for
UFS and one for the other PHY types.
In phy-qcom-ufs, remove the 'is_powered_on' and 'is_started' guards,
as the generic PHY code does the reference counting. The
14/20nm-specific init functions get collapsed into the generic power_on()
function, with the addition of a calibrate() callback specific to 14/20nm.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Move the PHY reset from ufs-qcom into the respective PHYs. This will
allow us to merge the two phases of UFS PHY initialization.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support for the shared USB3 + PCIE PHY found in the
Amlogic G12A SoC Family.
It supports USB3 Host mode or PCIE 2.0 mode, depending on the layout of
the board.
Selection is done by the #phy-cells, making the mode static and exclusive.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds support for the USB2 PHY found in the Amlogic G12A SoC Family.
It supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
USB PHY driver supports two types of stingray USB PHYs
- Type 1 is a combo PHY contains two PHYs, one SS and one HS.
- Type 2 is a single HS PHY.
These two PHY versons support both Generic xHCI host controller driver
and BDC Broadcom device controller driver.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the XUSB pad controller found on Tegra186 SoCs. It is
mostly similar to the same IP found on earlier chips, but the number of
pads exposed differs, as do the programming sequences.
Note that the DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL power
supplies of the XUSB pad controller require strict power sequencing and
are therefore controlled by the PMIC on Tegra186.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[dan.carpenter@oracle.com: Fix testing the wrong variable in probe()]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[yuehaibing@huawei.com: Make two functions static to fix sparse warning]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Support enabling various supplies needed to provide power to the PLLs
and logic used to drive the USB, PCI and SATA pads.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The device tree bindings document the "mode" property of "ports"
subnodes, but the driver was not parsing the property. In preparation
for adding role switching, parse the property at probe time.
Based on work by JC Kuo <jckuo@nvidia.com>.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tegra186 USB2 pads and USB3 pads do not have hardware mux for changing
the pad function. For such "lanes", we can skip the lane mux register
programming.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=GlRQ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-03-06' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is the main drm pull request for the 5.1 merge window.
The big changes I'd highlight are:
- nouveau has HMM support now, there is finally an in-tree user so we
can quieten down the rip it out people.
- i915 now enables fastboot by default on Skylake+
- Displayport Multistream support has been refactored and should
hopefully be more reliable.
Core:
- header cleanups aiming towards removing drmP.h
- dma-buf fence seqnos to 64-bits
- common helper for DP mst hotplug for radeon,i915,amdgpu + new
refcounting scheme
- MST i2c improvements
- drm_syncobj_cb removal
- ARM FB compression fourcc
- P010 + P016 fourcc
- allwinner tiled format modifier
- i2c over aux I2C_M_STOP support
- DRM_AUTH handling fixes
TTM:
- ref/unref renaming
New driver:
- ARM komeda display driver
scheduler:
- refactor mirror list handling
- rework hw fence processing
- 0 run queue entity fix
bridge:
- TI DS90C185 LVDS bridge
- thc631lvdm83d bridge improvements
- cadence + allwinner DSI ported to generic phy
panels:
- Sitronix ST7701 panel
- Kingdisplay KD097D04
- LeMaker BL035-RGB-002
- PDA 91-00156-A0
- Innolux EE101IA-01D
i915:
- Enable fastboot by default on SKL+/VLV/CHV
- Export RPCS configuration for ICL media driver
- Coffelake PCI ID
- CNL clocks setup fixes
- ACPI/PMIC support for MIPI/DSI
- Per-engine WA init for all engines
- Shrinker locking fixes
- Kerneldoc updates
- Lots of ring improvements and reset fixes
- Coffeelake GVT Support
- VFIO GVT EDID Region support
- runtime PM wakeref tracking
- ILK->IVB primary plane enable delays
- userptr mutex locking fixes
- DSI fixes
- LVDS/TV cleanups
- HW readout fixes
- LUT robustness fixes
- ICL display and watermark fixes
- gem mmap race fix
amdgpu:
- add scheduled dependencies interface
- DCC on scanout surfaces
- vega10/20 BACO support
- Multiple IH rings on soc15
- XGMI locking fixes
- DC i2c/aux cleanups
- runtime SMU debug interface
- Kexec improvmeents
- SR-IOV fixes
- DC freesync + ABM fixes
- GDS fixes
- GPUVM fixes
- vega20 PCIE DPM switching fixes
- Context priority handling fixes
radeon:
- fix missing break in evergreen parser
nouveau:
- SVM support via HMM
msm:
- QCOM Compressed modifier support
exynos:
- s5pv210 rotator support
imx:
- zpos property support
- pending update fixes
v3d:
- cache flush improvments
vc4:
- reflection support
- HDMI overscan support
tegra:
- CEC refactoring
- HDMI audio fixes
- Tegra186 prep work
- SOR crossbar device tree fixes
sun4i:
- implicit fencing support
- YUV and scalar support improvements
- A23 support
- tiling fixes
atmel-hlcdc:
- clipping and rotation property fixes
qxl:
- BO and PRIME improvements
- generic fbdev emulation
dw-hdmi:
- HDMI 2.0 2160p
- YUV420 ouput
rockchip:
- implicit fencing support
- reflection proerties
virtio-gpu:
- use generic fbdev emulation
tilcdc:
- cpufreq vs crtc init fix
rcar-du:
- R8A774C0 support
- D3/E3 RGB output routing fixes and DPAD0 support
- RA87744 LVDS support
bochs:
- atomic and generic fbdev emulation
- ID mismatch error on bochs load
meson:
- remove firmware fbs"
* tag 'drm-next-2019-03-06' of git://anongit.freedesktop.org/drm/drm: (1130 commits)
drm/amd/display: Use vrr friendly pageflip throttling in DC.
drm/imx: only send commit done event when all state has been applied
drm/imx: allow building under COMPILE_TEST
drm/imx: imx-tve: depend on COMMON_CLK
drm/imx: ipuv3-plane: add zpos property
drm/imx: ipuv3-plane: add function to query atomic update status
gpu: ipu-v3: prg: add function to get channel configure status
gpu: ipu-v3: pre: add double buffer status readback
drm/amdgpu: Bump amdgpu version for context priority override.
drm/amdgpu/powerplay: fix typo in BACO header guards
drm/amdgpu/powerplay: fix return codes in BACO code
drm/amdgpu: add missing license on baco files
drm/bochs: Fix the ID mismatch error
drm/nouveau/dmem: use dma addresses during migration copies
drm/nouveau/dmem: use physical vram addresses during migration copies
drm/nouveau/dmem: extend copy function to allow direct use of physical addresses
drm/nouveau/svm: new ioctl to migrate process memory to GPU memory
drm/nouveau/dmem: device memory helpers for SVM
drm/nouveau/svm: initial support for shared virtual memory
drm/nouveau: prepare for enabling svm with existing userspace interfaces
...
Here is the big USB/PHY driver pull request for 5.1-rc1.
The usual set of gadget driver updates, phy driver updates (you will
have a merge issue with Kconfig and Makefile), xhci updates, and typec
additions. Also included in here are a lot of small cleanups and fixes
and driver updates where needed.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+hsw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynfNwCgqKKg+MxJ9pFjrwfWYOrbk+BBe2UAn2Elp4ia
8FTdneQfN2J8Hhc6KGXE
=Kx9I
-----END PGP SIGNATURE-----
Merge tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver pull request for 5.1-rc1.
The usual set of gadget driver updates, phy driver updates, xhci
updates, and typec additions. Also included in here are a lot of small
cleanups and fixes and driver updates where needed.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
wusb: Remove unnecessary static function ckhdid_printf
usb: core: make default autosuspend delay configurable
usb: core: Fix typo in description of "authorized_default"
usb: chipidea: Refactor USB PHY selection and keep a single PHY
usb: chipidea: Grab the (legacy) USB PHY by phandle first
usb: chipidea: imx: set power polarity
dt-bindings: usb: ci-hdrc-usb2: add property power-active-high
usb: chipidea: imx: remove unused header files
usb: chipidea: tegra: Fix missed ci_hdrc_remove_device()
usb: core: add option of only authorizing internal devices
usb: typec: tps6598x: handle block writes separately with plain-I2C adapters
usb: xhci: Fix for Enabling USB ROLE SWITCH QUIRK on INTEL_SUNRISEPOINT_LP_XHCI
usb: xhci: fix build warning - missing prototype
usb: xhci: dbc: Fixing typo error.
usb: xhci: remove unused member 'parent' in xhci_regset struct
xhci: tegra: Prevent error pointer dereference
USB: serial: option: add Telit ME910 ECM composition
usb: core: Replace hardcoded check with inline function from usb.h
usb: core: skip interfaces disabled in devicetree
usb: typec: mux: remove redundant check on variable match
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxqHJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWl8H/jPI4EipzD2GbnjZ
GaFpMBBjcXBaVmoA+Y69so+7BHx1Ql+5GQtqbK0RHJRb9qEPLw3FBhHNjM/N8Sgf
nSrK+GnBZp9s+k/NR/Yf2RacUR3jhz+Q9JEoQd3u9bFUeQyvE8Rf3vgtoBBwFOfz
+t7N1memYVF3asLGWB4e4sP1YVMGfseTQpSPojvM30YWM86Bv+QtSx1AGgHczQIM
kMKealR8ZPelN6JAXgLhQ5opDojBrE4YKB98pwsMDI6abz0Tz2JLFEUTTxsv5XNN
o/Iz+XDoylskEyxN2unNWfHx7Swkvoklog8J/hDg5XlTvipL/WkT66PHBgcGMNvj
BW9GgU8=
=ZizU
-----END PGP SIGNATURE-----
Merge v5.0-rc7 into drm-next
Backmerging for nouveau and imx that needed some fixes for next pulls.
Signed-off-by: Dave Airlie <airlied@redhat.com>
*) Add a new driver to support Armada 3700 COMPHY IP (supports SATA, USB3,
PCIe)
*) Add a new driver to support Armada UTMI PHY
*) Add a new driver to support Cadence D-PHY
*) Extend omap-usb2 PHY driver to be used for AM654 USB2 PHY
*) Extend qcom-qmp PHY driver to be used for UFS PHY and USB3 PHY in Qualcomm
MSM8998
*) Extend qcom-qusb2 PHY driver to support QUSB2 PHY in Qualcomm MSM8998
*) Remove module specific code that is present for drivers that can be only
built-in
*) Allow Freescale IMX8MQ USB to be used for multiple SoCs and not just
i.MX8MQ
*) Cleanups such as switch to SPDX identifier, use readl_poll_timeout macro,
remove unused headers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=wNhh
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.1
*) Add a new driver to support Armada 3700 COMPHY IP (supports SATA, USB3,
PCIe)
*) Add a new driver to support Armada UTMI PHY
*) Add a new driver to support Cadence D-PHY
*) Extend omap-usb2 PHY driver to be used for AM654 USB2 PHY
*) Extend qcom-qmp PHY driver to be used for UFS PHY and USB3 PHY in Qualcomm
MSM8998
*) Extend qcom-qusb2 PHY driver to support QUSB2 PHY in Qualcomm MSM8998
*) Remove module specific code that is present for drivers that can be only
built-in
*) Allow Freescale IMX8MQ USB to be used for multiple SoCs and not just
i.MX8MQ
*) Cleanups such as switch to SPDX identifier, use readl_poll_timeout macro,
remove unused headers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (32 commits)
phy: qcom-qmp: Add QMP UFS PHY support for msm8998
dt-bindings: phy-qcom-qmp: Add qcom,msm8998-qmp-ufs-phy
phy: bcm-sr-pcie: Change operation when PIPEMUX=1
phy: Add Cadence D-PHY support
dt-bindings: phy: Move the Cadence D-PHY bindings
phy: dphy: Clarify lanes parameter documentation
phy: dphy: Change units of wakeup and init parameters
phy: dphy: Remove unused header
MAINTAINERS: phy: fill Armada 3700 PHY drivers entry
dt-bindings: phy: mvebu-utmi: add UTMI PHY bindings
phy: add A3700 UTMI PHY driver
MAINTAINERS: phy: add entry for Armada 3700 COMPHY driver
dt-bindings: phy: mvebu-comphy: extend the file to describe a3700 bindings
phy: add A3700 COMPHY support
phy: mvebu-cp110-comphy: fix port check in ->xlate()
phy: armada375-usb2: switch to SPDX license identifier
phy: make phy-armada375-usb2 explicitly non-modular
phy: make phy-mvebu-sata explicitly non-modular
phy: make phy-core explicitly non-modular
phy: qcom-qusb2: Add QUSB2 PHY support for msm8998
...
Use same init sequence as sdm845.
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the Armada 38x common phy to allow us to change the
speed of the Ethernet serdes lane. This driver only supports
manipulation of the speed, it does not support configuration of the
common phy.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PIPEMIX=1, change the operation from 2x8 EP to 1x8 EP + 1x8 RC.
Signed-off-by: Qingmin Liu <qingmin.liu@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cadence has designed a D-PHY that can be used by the, currently in tree,
DSI bridge (DRM), CSI Transceiver and CSI Receiver (v4l2) drivers.
Only the DSI driver has an ad-hoc driver for that phy at the moment, while
the v4l2 drivers are completely missing any phy support. In order to make
that phy support available to all these drivers, without having to
duplicate that code three times, let's create a generic phy framework
driver.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Init and wakeup D-PHY parameters are in the micro/milliseconds range,
putting the values real close to the types limits if they were in
picoseconds.
Move them to microseconds which should be better fit.
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Marvell Armada 3700 SoC has two USB controllers, each of them being
wired to an internal UTMI PHY. Add a driver to control them.
Igal Liberman worked on supporting the PHY, I took the while 'register
configuration' from his work and rewrote almost entirely the
driver/bindings around it.
Co-developed-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a driver to support COMPHY, a hardware block providing shared
serdes PHYs on Marvell Armada 3700. This driver uses SMC calls and
rely on having an up-to-date firmware.
SATA, PCie and USB3 host mode have been tested successfully with an
ESPRESSObin. (HS)SGMII mode cannot be tested with this platform.
Evan worked on the original driver structure and Grzegorz on the SMC
calls rework. The structure of this driver has been copied from
Antoine Tenart work on CP110 COMPHY driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Co-developed-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Evan Wang <xswang@marvell.com>
Co-developed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
So far the PHY ->xlate() callback was checking if the port was
"invalid" before continuing, meaning that the port has not been used
yet. This check is not correct as there is no opposite call to
->xlate() once the PHY is released by the user and the port will
remain "valid" after the first phy_get()/phy_put() calls. Hence, if
this driver is built as a module, inserted, removed and inserted
again, the PHY will appear busy and the second probe will fail.
To fix this, just drop the faulty check and instead verify that the
port number is valid (ie. in the possible range).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Kconfig currently controlling compilation of this code is:
drivers/phy/marvell/Kconfig:config ARMADA375_USBCLUSTER_PHY
drivers/phy/marvell/Kconfig: def_bool y
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple of traces of modular infrastructure, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Kconfig currently controlling compilation of this code is:
drivers/phy/Kconfig:config PHY_MVEBU_SATA
drivers/phy/Kconfig: def_bool y
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple of traces of modular infrastructure, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Kconfig currently controlling compilation of this code is:
drivers/phy/Kconfig:config GENERIC_PHY
drivers/phy/Kconfig: bool "PHY Core"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't remove module.h since the file is using other modular fcns
(to load other phy modules) even though the core support itself is
non-modular.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
MSM8998 contains one QUSB2 PHY which is very similar to the existing
sdm845 support.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
That property is no used in mainline and is not documented. The only
board using that property is the rk33-99-evb-rev1 and -rev2 in the
vendor kernel. The existence of a further -rev3 (which also looks way
better cared for compared rev1+2) indicates that the older ones are
probably some sort of preproduction models, where some wiring (on the soc
or board) may have gone wrong.
It is also not clear why this is a hardware-description or a DT
property, so, as noboby seems to care of this just drop reading that
property.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
MSM8998 contains a single QMP v3 USB3 phy similar to the existing sdm845
support.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix the typo flase -> false and clean up the kernel-doc documentation in
phy-rockchip-inno.usb2.c and fix the following warnings when documentation
is built.
:58: warning: missing initial short description
:69: warning: cannot understand function prototype: 'enum usb_chg_state '
:97: warning: missing initial short description
:136: warning: cannot understand function prototype: 'struct rockchip_usb2phy_port_cfg '
:157: warning: cannot understand function prototype: 'struct rockchip_usb2phy_cfg '
:163: warning: Function parameter or member 'port_cfgs' not described in 'rockchip_usb2phy_cfg'
:187: warning: cannot understand function prototype: 'struct rockchip_usb2phy_port '
:204: warning: Function parameter or member 'port_cfg' not described in 'rockchip_usb2phy_port'
:207: warning: missing initial short description
:234: warning: Function parameter or member 'dev' not described in 'rockchip_usb2phy'
:234: warning: Function parameter or member 'clk480m_hw' not described in 'rockchip_usb2phy'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the USB2 PHY on the AM654 SoC.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
TI_PIPE3 and OMAP_USB2 don't depend on OMAP_OCP2SCP
for build.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
If clk_get() returns -EPROBE_DEFER then we should just
return instead of falling back to old clock name.
Use clk_prepare_enable() and clk_disable_unprepare() instead
of splitting up prepare/unprepare from enable/disable.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The private copy of readl_poll_timeout is no longer needed.
Use the implementation in iopoll.h instead.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since this is going to be used on more SoCs than just i.MX8MQ,
make the dependency here more generic.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here are a number of small USB and PHY driver fixes for 5.0-rc4.
Nothing major at all, just the usual selection of USB gadget bugfixes,
some new USB serial driver ids, some SPDX fixes, and some PHY driver
fixes for reported issues.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXEr9Iw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yltXACg1ycTrlsIDEtj0fQb0KpgmovzYMEAn02nv62w
+6bHM1m+RZvKw5DnOrKb
=g6YM
-----END PGP SIGNATURE-----
Merge tag 'usb-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are a number of small USB and PHY driver fixes for 5.0-rc4.
Nothing major at all, just the usual selection of USB gadget bugfixes,
some new USB serial driver ids, some SPDX fixes, and some PHY driver
fixes for reported issues.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: keyspan_usa: add proper SPDX lines for .h files
USB: EHCI: ehci-mv: add MODULE_DEVICE_TABLE
USB: leds: fix regression in usbport led trigger
usb: chipidea: fix static checker warning for NULL pointer
MAINTAINERS: email address update in MAINTAINERS entries
USB: usbip: delete README file
USB: serial: pl2303: add new PID to support PL2303TB
usb: dwc2: gadget: Fix Remote Wakeup interrupt bit clearing
phy: ath79-usb: Fix the main reset name to match the DT binding
phy: ath79-usb: Fix the power on error path
phy: fix build breakage: add PHY_MODE_SATA
phy: ti: ensure priv is not null before dereferencing it
USB: serial: ftdi_sio: fix GPIO not working in autosuspend
usb: gadget: Potential NULL dereference on allocation error
usb: dwc3: gadget: Fix the uninitialized link_state when udc starts
usb: dwc3: gadget: Clear req->needs_extra_trb flag on cleanup
usb: dwc3: gadget: synchronize_irq dwc irq in suspend
USB: serial: simple: add Motorola Tetra TPG2200 device id
I submitted this driver several times before it got accepted. The
first series hasn't been accepted but the DTS binding did made it.
I then made a second series that added generic reset support to the
PHY core, this in turn required a change to the DT binding. This
second series seemed to have been ignored, so I did a third one
without the change to the PHY core and the DT binding update, and this
last attempt finally made it.
But two months later the DT binding update from the second series has
been integrated too. So now the driver doesn't match the binding and
the only DTS using it. This patch fix the driver to match the new
binding.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In the power on function the error path doesn't return the suspend
override to its proper state. It should should deassert this reset
line to enable the suspend override.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 49e54187ae ("ata: libahci_platform: comply to PHY framework") uses
the PHY_MODE_SATA, but that enum had not yet been added. This caused a
build failure for me, with today's linux.git.
Also, there is a potentially conflicting (mis-named) PHY_MODE_SATA, hiding
in the Marvell Berlin SATA PHY driver.
Fix the build by:
1) Renaming Marvell's defined value to a more scoped name,
in order to avoid any potential conflicts: PHY_BERLIN_MODE_SATA.
2) Adding the missing enum, which was going to be added anyway as part
of [1].
[1] https://lkml.kernel.org/r/20190108163124.6409-3-miquel.raynal@bootlin.com
Fixes: 49e54187ae ("ata: libahci_platform: comply to PHY framework")
Cc: Grzegorz Jaszczyk <jaz@semihalf.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently priv is being dereferenced before priv is being null checked.
Fix this by moving the null check on priv before the dereference.
Detected by CoverityScan, CID#1476018 ("Dereference before null check")
Fixes: 92b58b3474 ("phy: ti: introduce phy-gmii-sel driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pull networking fixes from David Miller:
1) Fix regression in multi-SKB responses to RTM_GETADDR, from Arthur
Gautier.
2) Fix ipv6 frag parsing in openvswitch, from Yi-Hung Wei.
3) Unbounded recursion in ipv4 and ipv6 GUE tunnels, from Stefano
Brivio.
4) Use after free in hns driver, from Yonglong Liu.
5) icmp6_send() needs to handle the case of NULL skb, from Eric
Dumazet.
6) Missing rcu read lock in __inet6_bind() when operating on mapped
addresses, from David Ahern.
7) Memory leak in tipc-nl_compat_publ_dump(), from Gustavo A. R. Silva.
8) Fix PHY vs r8169 module loading ordering issues, from Heiner
Kallweit.
9) Fix bridge vlan memory leak, from Ido Schimmel.
10) Dev refcount leak in AF_PACKET, from Jason Gunthorpe.
11) Infoleak in ipv6_local_error(), flow label isn't completely
initialized. From Eric Dumazet.
12) Handle mv88e6390 errata, from Andrew Lunn.
13) Making vhost/vsock CID hashing consistent, from Zha Bin.
14) Fix lack of UMH cleanup when it unexpectedly exits, from Taehee Yoo.
15) Bridge forwarding must clear skb->tstamp, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
bnxt_en: Fix context memory allocation.
bnxt_en: Fix ring checking logic on 57500 chips.
mISDN: hfcsusb: Use struct_size() in kzalloc()
net: clear skb->tstamp in bridge forwarding path
net: bpfilter: disallow to remove bpfilter module while being used
net: bpfilter: restart bpfilter_umh when error occurred
net: bpfilter: use cleanup callback to release umh_info
umh: add exit routine for UMH process
isdn: i4l: isdn_tty: Fix some concurrency double-free bugs
vhost/vsock: fix vhost vsock cid hashing inconsistent
net: stmmac: Prevent RX starvation in stmmac_napi_poll()
net: stmmac: Fix the logic of checking if RX Watchdog must be enabled
net: stmmac: Check if CBS is supported before configuring
net: stmmac: dwxgmac2: Only clear interrupts that are active
net: stmmac: Fix PCI module removal leak
tools/bpf: fix bpftool map dump with bitfields
tools/bpf: test btf bitfield with >=256 struct member offset
bpf: fix bpffs bitfield pretty print
net: ethernet: mediatek: fix warning in phy_start_aneg
tcp: change txhash on SYN-data timeout
...
Commit 49e54187ae ("ata: libahci_platform: comply to PHY framework") uses
the PHY_MODE_SATA, but that enum had not yet been added. This caused a
build failure for me, with today's linux.git.
Also, there is a potentially conflicting (mis-named) PHY_MODE_SATA, hiding
in the Marvell Berlin SATA PHY driver.
Fix the build by:
1) Renaming Marvell's defined value to a more scoped name,
in order to avoid any potential conflicts: PHY_BERLIN_MODE_SATA.
2) Adding the missing enum, which was going to be added anyway as part
of [1].
[1] https://lkml.kernel.org/r/20190108163124.6409-3-miquel.raynal@bootlin.com
Fixes: 49e54187ae ("ata: libahci_platform: comply to PHY framework")
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Grzegorz Jaszczyk <jaz@semihalf.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver requires regmap or the compile fails:
drivers/phy/ti/phy-gmii-sel.c:43:27: error: array type has incomplete element type ‘struct reg_field’
const struct reg_field (*regfields)[PHY_GMII_SEL_LAST];
Add it to kconfig.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register a simple clock provider for the PHY pipe clock sources so that
device tree users can point at these clocks via phandles to the lane
nodes.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Utilize the newly fixed up DT bindings to get the tx2 and rx2 register
regions for the second lane of dual-lane PHYs. Before this change,
the driver was simply using lane one's register region and adding
0x400, which reached well beyond the DT-specified register
allocation. This would have been a crash were it not for the page size
on ARM64. Fix the driver not to rely on the magic of virtual memory by
using the newly specified DT register regions for tx2 and rx2.
In order to support existing device trees, this change also contains a
fallback mode for when those new register regions don't exist, which
reverts to the original behavior of overreaching and prints a complaint.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
