The IOMMU may not always be able to address 2 GiB of memory. On Tegra20,
the GART supports 32 MiB starting at 0x58000000. Also the aperture on
Tegra30 and later is in fact the full 4 GiB, rather than just 2 GiB as
currently assumed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Perhaps the most noteworthy change in this set is the implementation of
a hardware VBLANK counter using host1x syncpoints. The SOR registers can
now be dumped via debugfs, which can be useful while debugging. The IOVA
address space maintained by the driver can also be dumped via debugfs.
Other than than, these changes are mostly cleanup work, such as making
register names more consistent or removing unused code (that was left
over after the atomic mode-setting conversion). There's also a fix for
eDP that makes the driver cope with firmware that already initialized
the display (such as the firmware on the Tegra-based Chromebooks).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=HZO1
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.1-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.1-rc1
Perhaps the most noteworthy change in this set is the implementation of
a hardware VBLANK counter using host1x syncpoints. The SOR registers can
now be dumped via debugfs, which can be useful while debugging. The IOVA
address space maintained by the driver can also be dumped via debugfs.
Other than than, these changes are mostly cleanup work, such as making
register names more consistent or removing unused code (that was left
over after the atomic mode-setting conversion). There's also a fix for
eDP that makes the driver cope with firmware that already initialized
the display (such as the firmware on the Tegra-based Chromebooks).
* tag 'drm/tegra/for-4.1-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: sor: Reset during initialization
drm/tegra: gem: Return 64-bit offset for mmap(2)
drm/tegra: hdmi: Name register fields consistently
drm/tegra: hdmi: Resets are synchronous
drm/tegra: dc: Document tegra_dc_state_setup_clock()
drm/tegra: dc: Remove unused callbacks
drm/tegra: dc: Remove unused function
drm/tegra: dc: Use base atomic state helpers
drm/atomic: Add helpers for state-subclassing drivers
drm/tegra: dc: Implement hardware VBLANK counter
gpu: host1x: Export host1x_syncpt_read()
drm/tegra: sor: Dump registers via debugfs
drm/tegra: sor: Registers are 32-bit
drm/tegra: Provide debugfs file for the IOVA space
drm/tegra: dc: Check for valid parent clock
The display controller on Tegra can use syncpoints to count VBLANK
events. syncpoints are 32-bit unsigned integers, so well suited as
VBLANK counters.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra DRM driver uses a single IO virtual address space for buffer
mappings. Provide a table of the address space usage in debugfs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
These names only make sense because of backwards compatability with
the order used by the crtc helper library. There's not really any real
requirement in the ordering here.
So rename them to something more descriptive and update the kerneldoc
a bit. Motivated in a discussion with Laurent about how to restore
plane state for dpms for drivers with runtime pm.
v2: Squash in fixup from Stephen Rothwell to fix a conflict with
tegra.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When copying a relocation from userspace, copy the correct target
offset.
Signed-off-by: David Ung <davidu@nvidia.com>
Fixes: 961e3beae3 ("drm/tegra: Make job submission 64-bit safe")
Cc: stable@vger.kernel.org
[treding@nvidia.com: provide a better commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
For now only disable the KMS hotplug polling helper logic upon suspend
and re-enable it on resume.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Provide a custom ->atomic_commit() implementation which supports async
commits. The generic atomic page-flip helper can use this to implement
page-flipping.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Switch out the regular plane helpers for the atomic plane helpers. Also
use the default atomic helpers to implement the ->atomic_check() and
->atomic_commit() callbacks. The driver now exclusively uses the atomic
interfaces.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Hook up the default ->reset() and ->atomic_duplicate_state() helpers.
This ensures that state objects are properly created and framebuffer
reference counts correctly maintained.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement initial atomic state handling. Hook up the CRTCs, planes' and
connectors' ->atomic_destroy_state() callback to ensure that the atomic
state objects don't leak.
Furthermore the CRTC now implements the ->mode_set_nofb() callback that
is used by new helpers to implement ->mode_set() and ->mode_set_base().
These new helpers also make use of the new plane helper functions which
the driver now provides.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This structure will be extended using non-framebuffer related callbacks
in subsequent patches, so it should move to a more central location.
Signed-off-by: Thierry Reding <treding@nvidia.com>
iommu_domain_alloc() returns NULL on error, it never returns error
pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously the struct bus_type exported by the host1x infrastructure was
only a very basic skeleton. Turn that implementation into a more full-
fledged bus to support proper probe ordering and power management.
Note that the bus infrastructure needs to be available before any of the
drivers can be registered. This is automatically ensured if all drivers
are built as loadable modules (via symbol dependencies). If all drivers
are built-in there are no such guarantees and the link order determines
the initcall ordering. Adjust drivers/gpu/Makefile to make sure that the
host1x bus infrastructure is initialized prior to any of its users (only
drm/tegra currently).
v2: Fix building host1x and tegra-drm as modules
Reported-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The hardware pipe numbers don't always match the DRM CRTC indices. This
can happen for example if the first display controller defers probe,
causing it to be registered with DRM after the second display
controller. When that happens the hardware pipe numbers and DRM CRTC
indices become different. Make sure that the CRTC index is always used
when accessing per-CRTC VBLANK data. This can be ensured by using the
drm_crtc_vblank_*() API, which will do the right thing automatically
given a struct drm_crtc *.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When an IOMMU device is available on the platform bus, allocate an IOMMU
domain and attach the display controllers to it. The display controllers
can then scan out non-contiguous buffers by mapping them through the
IOMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM driver's ->load() implementation didn't do a good job (no job at
all really) cleaning up on failure. Fix that by undoing any prior setup
when an error occurs. This requires a bit of rework to make it possible
to clean up fbdev midway.
This was tested by injecting errors at various points during the
initialization sequence and verifying that error cleanup didn't crash
and no memory leaked (using kmemleak).
Reported-by: Stéphane Marchesin <marcheu@chromium.org>
Reported-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Job submission currently relies on the fact that struct drm_tegra_reloc
and struct host1x_reloc are the same size and uses a simple call to the
copy_from_user() function to copy them to kernel space. This causes the
handle to be stored in the buffer object field, which then needs a cast
to a 32 bit integer to resolve it to a proper buffer object pointer and
store it back in the buffer object field.
On 64-bit architectures that will no longer work, since pointers are 64
bits wide whereas handles will remain 32 bits. This causes the sizes of
both structures to because different and copying will no longer work.
Fix this by adding a new function, host1x_reloc_get_user(), that copies
the structures field by field.
While at it, use substructures for the command and target buffers in
struct host1x_reloc for better readability. Also use unsized types to
make it more obvious that this isn't part of userspace ABI.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This matches what other drivers do for equivalent IOCTLs.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM_TEGRA_GEM_SET_FLAGS IOCTL can be used to set the flags of a
buffer object after it has been allocated or imported. Flags associated
with a buffer object can be queried using the DRM_TEGRA_GEM_GET_FLAGS
IOCTL.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the tiling parameters of buffer objects can only be set at
allocation time, and only a single tiled mode is supported. This new
DRM_TEGRA_GEM_SET_TILING IOCTL allows more modes to be set and also
allows the tiling mode to be changed after the allocation. This will
enable the Tegra DRM driver to import buffers from a GPU and directly
scan them out by configuring the display controller appropriately.
To complement this, the DRM_TEGRA_GEM_GET_TILING IOCTL can query the
current tiling mode of a buffer object. This is necessary when importing
buffers via handle (as is done in Mesa for example) so that userspace
can determine the proper parameters for the 2D or 3D engines.
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A race condition currently exists on Tegra, where it can happen that a
monitor attached via HDMI isn't detected during the initial FB helper
setup, but the hotplug event happens too early to be processed by the
poll helpers because they haven't been initialized yet. This happens
because on some boards the HDMI driver can control the regulator that
supplies the +5V pin on the HDMI connector. Therefore depending on the
timing between the initialization of the HDMI driver and the rest of
DRM, it's possible that the monitor returns the hotplug signal right
within the window where we would miss it.
Unfortunately, drm_kms_helper_poll_init() will wreak havoc when called
before at least some parts of the FB helpers have been set up.
This commit fixes this by splitting out the minimum of initialization
required to make drm_kms_helper_poll_init() work into a separate
function that can be called early. It is then safe to move all of the
poll helper initialization to an earlier point in time (before the
HDMI output driver has a chance to enable the +5V supply). That way if
the hotplug signal is returned before the initial FB helper setup, the
monitor will be forcefully detected at that point, and if the hotplug
signal is returned after that it will be properly handled by the poll
helpers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DRM core can now cope with drivers that don't have an associated
struct drm_bus, so the host1x implementation is no longer useful.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 is mostly backwards-compatible with Tegra114. However, Tegra124
supports a few more features (e.g. interlacing, ...). Introduce a new
compatible string and TMDS tables to cope with these differences.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement eDP support for Tegra124 and support the PRIME vmap()/vunmap()
operations.
A symbol that is required for upcoming V4L2 support is now exported by
the host1x driver.
Relicense drivers under the GPL v2 for consistency. One exception is the
public header file, which is relicensed under MIT to abide by the common
rule.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=LGu0
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.15-rc1
Implement eDP support for Tegra124 and support the PRIME vmap()/vunmap()
operations.
A symbol that is required for upcoming V4L2 support is now exported by
the host1x driver.
Relicense drivers under the GPL v2 for consistency. One exception is the
public header file, which is relicensed under MIT to abide by the common
rule.
* tag 'drm/tegra/for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Use standard GPL v2 license text
drm/tegra: Relicense under GPL v2
drm/tegra: Relicense public header under MIT
drm/tegra: Add eDP support
gpu: host1x: export host1x_syncpt_incr_max() function
drm/tegra: prime: Add vmap support
Add support for eDP functionality found on Tegra124 and later SoCs. Only
fast link training is currently supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement very basic PRIME support. This currently only works with
buffers that are contiguous in memory and will refuse to import any
physically non-contiguous buffers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 and later support interlacing, but the driver doesn't support
it yet. Make sure interlacing stays disabled on hardware that supports
it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
A lot of the modern userspace is capable of working without the legacy
fbdev support. kmscon can be used as a replacement for the framebuffer
console, and KMS X drivers create their own framebuffers.
Most people don't have a system where all of this works yet, though, so
leave support enabled by default.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features like ganged
mode won't work.
Due to the lack of other test hardware, some sections of the driver are
hardcoded to work with Dalmore.
Signed-off-by: Thierry Reding <treding@nvidia.com>
copy_from_user() returns the number of bytes remaining if it fails, but
we want to return -EFAULT here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds a separate ioctl for delivering syncpoint base number
to user space. If the syncpoint does not have an associated base, the
function returns -ENXIO.
Signed-off-by: Arto Merilainen <amerilainen@nvidia.com>
Reviewed-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The gr2d and gr3d engines work more efficiently on buffers with a tiled
memory layout. Allow created buffers to be marked as tiled so that the
display controller can scan them out properly.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Initialize and power the 3D unit on Tegra20, Tegra30 and Tegra114 and
register a channel with the Tegra DRM driver so that the unit can be
used from userspace.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Command stream submissions are the same across all devices that expose
a channel to userspace, so move the code into a generic function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra114 TMDS configuration requires a new peak_current field and the
driver current override bit has changed position.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the DRM driver is unloaded, all the associated resources must be
cleaned up and zeroed out. This is necessary because of the architecture
of the Tegra DRM driver, where not all subdrivers are unloaded along
with the DRM driver. Therefore device-managed managed won't be freed and
memory cannot be assumed to have been cleared (because it hasn't been
reallocated using kzalloc()) by the time the DRM driver is reloaded. It
is therefore necessary to zero out the structures to prevent strange
errors (such as slab corruptions) from occurring.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
This list is most useful to inspect whether framebuffer reference
counting works as expected. The code is loosely based on the i915
implementation.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
All the necessary support bits like .mode_set_base() and VBLANK are now
available, so page-flipping case easily be implemented on top.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Implement support for the VBLANK IOCTL. Note that Tegra is somewhat
special in this case because it doesn't use the generic IRQ support
provided by the DRM core (DRIVER_HAVE_IRQ) but rather registers one
interrupt handler for each display controller.
While at it, clean up the way that interrupts are enabled to ensure
that the VBLANK interrupt only gets enabled when required.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Migrate Tegra clock support to drivers/clk/tegra, this involves
moving:
1. definition of tegra_cpu_car_ops to clk.c
2. definition of reset functions to clk-peripheral.c
3. change parent of cpu clock.
4. Remove legacy clock initialization.
5. Initialize clocks using DT.
6. Remove all instance of mach/clk.h
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: use to_clk_periph_gate().]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This commit adds a KMS driver for the Tegra20 SoC. This includes basic
support for host1x and the two display controllers found on the Tegra20
SoC. Each display controller can drive a separate RGB/LVDS output.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Zhang <markz@nvidia.com>
Reviewed-by: Mark Zhang <markz@nvidia.com>
Tested-by: Mark Zhang <markz@nvidia.com>
Tested-and-acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Terje Bergstrom <tbergstrom@nvidia.com>
Tested-by: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>