Add support for receiving packets via AF_XDP zero-copy mechanism.
Add a new flag to 'enum igc_ring_flags_t' to indicate the ring has
AF_XDP zero-copy enabled so proper ring setup is carried out during ring
configuration in igc_configure_rx_ring().
RX buffers can now be allocated via the shared pages mechanism (default
behavior of the driver) or via xsk pool (when AF_XDP zero-copy is
enabled) so a union is added to the 'struct igc_rx_buffer' to cover both
cases.
When AF_XDP zero-copy is enabled, rx buffers are allocated from the xsk
pool using the new helper igc_alloc_rx_buffers_zc() which is the
counterpart of igc_alloc_rx_buffers().
Likewise other Intel drivers that support AF_XDP zero-copy, in igc we
have a dedicated path for cleaning up rx irqs when zero-copy is enabled.
This avoids adding too many checks within igc_clean_rx_irq(), resulting
in a more readable and efficient code since this function is called from
the hot-path of the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Up to this point, Tx buffers are associated with either a skb or a xdpf,
and the IGC_TX_FLAGS_XDP flag was enough to distinguish between these
two case. However, with upcoming patches that will add AF_XDP zero-copy
support, a third case will be introduced so this flag-based approach
won't fit well.
In preparation to land AF_XDP zero-copy support, replace the
IGC_TX_FLAGS_XDP flag by an enum which will be extended once zero-copy
support is introduced to the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation for AF_XDP zero-copy support, encapsulate the code that
unmaps Tx buffers into its own local helper so we can reuse it, avoiding
code duplication.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In preparation for AF_XDP zero-copy support, encapsulate the code that
updates the driver RX stats in its own local helper so it can be reused
in the zero-copy path. Likewise, encapsulate TX stats code as well.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor XDP rxq info registration code, preparing the driver for AF_XDP
zero-copy support which is added by upcoming patches.
Currently, xdp_rxq and memory model are both registered during RX
resource setup time by igc_xdp_register_rxq_info() helper. With AF_XDP,
we want to register the memory model later on while configuring the ring
because we will know which memory model type to register
(MEM_TYPE_PAGE_SHARED or MEM_TYPE_XSK_BUFF_POOL).
The helpers igc_xdp_register_rxq_info() and igc_xdp_unregister_rxq_
info() are not useful anymore so they are removed.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor igc_clean_rx_ring() helper, preparing the code for AF_XDP
zero-copy support which is added by upcoming patches.
The refactor consists of encapsulating page-shared specific code into
its own helper, leaving common code that will be shared by both
page-shared and xsk pool in igc_clean_rx_ring().
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor __igc_xdp_run_prog() helper from igc_xdp_run_prog(),
preparing the code for AF_XDP zero-copy support which is added
by upcoming patches.
The existing igc_xdp_run_prog() caters to regular XDP rx path
which has to verify if bpf_prog is not NULL. Zero-copy
path assumes that bpf_prog is not NULL and hence this check is
not required. Therefore it makes sense to refactor the common
code into a helper function, to avoid code duplication.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move the helper igc_xdp_is_enabled() to igc_xdp.h so it can be reused in
igc_xdp.c by upcoming patches that will introduce AF_XDP zero-copy
support to the driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make use of the xdp_{init,prepare}_buff() helpers instead of
an open-coded version.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i225 device offers a number of special PTP Hardware Clock features on
the Software Defined Pins (SDPs) - much like i210, which is used as
inspiration for this patch. It enables two possible functions, namely
time stamping external events and periodic output signals.
The assignment of PHC functions to the four SDP can be freely chosen by
the user.
For the external events time stamping, when the SDP (configured as input
by user) level changes, an interrupt is generated and the kernel
Precision Time Protocol (PTP) is informed.
For the periodic output signals, the i225 is configured to generate them
(so the SDP level will change periodically) and the driver also has to
keep updating the time of the next level change. However, this work is
not necessary for some frequencies as the i225 takes care of them
(namely, anything with a half-cycle of 500ms, 250ms, 125ms or < 70ms).
While i225 allows up to four timers to be used to source the time used
on the external events or output signals, this patch uses only one of
those timers. Main reason is to keep it simple, as it's not clear how
these extra timers would be exposed to users. Note that currently a NIC
can expose a single PTP device.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The i225 device can produce one interrupt on the full second, much
like i210 - from where this patch is inspired.
This patch sets up the full second interruption on the i225 and when
receiving it, it sends a PPS event to PTP (Precision Time Protocol)
kernel subsystem.
The PTP subsystem exposes the PPS events via ioctl and sysfs, and one
can use the `testptp` tool (tools/testing/selftests/ptp) to check that
the events are being generated.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for the XDP_REDIRECT action which enables XDP programs to
redirect packets arriving at I225 NIC. It also implements the
ndo_xdp_xmit ops, enabling the igc driver to transmit packets forwarded
to it by xdp programs running on other interfaces.
The patch tweaks the driver's page counting and recycling scheme as
described in the following two commits and implemented by other Intel
drivers in order to properly support XDP_REDIRECT action:
commit 8ce29c679a ("i40e: tweak page counting for XDP_REDIRECT")
commit 75aab4e10a ("i40e: avoid premature Rx buffer reuse")
This patch has been tested with the sample apps "xdp_redirect_cpu" and
"xdp_redirect_map" located in samples/bpf/.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for XDP_TX action which enables XDP programs to transmit
back receiving frames.
I225 controller has only 4 Tx hardware queues. Since XDP programs may
not even issue an XDP_TX action, this patch doesn't reserve dedicated
queues just for XDP like other Intel drivers do. Instead, the queues
are shared between the network stack and XDP. The netdev queue lock is
used to ensure mutual exclusion.
Since frames can now be transmitted via XDP_TX, the igc_tx_buffer
structure is modified so we are able to save a reference to the xdp
frame for later clean up once the packet is transmitted. The tx_buffer
is mapped to either a skb or a xdpf so we use a union to save the skb
or xdpf pointer and have a bit in tx_flags to indicate which field to
use.
This patch has been tested with the sample app "xdp2" located in
samples/bpf/ dir.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the initial XDP support to the igc driver. For now, only XDP_PASS,
XDP_DROP, XDP_ABORTED actions are supported. Upcoming patches will add
support for the remaining XDP actions.
XDP configuration helpers are defined in a new file, igc_xdp.c. These
helpers are utilized in igc_main.c to implement the ndo_bpf callback.
XDP-related code that belongs to the driver's hot path is landed in
igc_main.c.
By default, the driver uses Rx buffers with 2 KB size. When XDP is
enabled, it uses larger buffers so we have enough space to accommodate
the headroom and tailroom required by XDP infrastructure. Also, the
driver doesn't support XDP functionality with frames that span over
multiple buffers so jumbo frames are not allowed for now.
The approach implemented follows the approach implemented in other Intel
drivers as much as possible for the sake of consistency across the
drivers.
Quick comment regarding igc_build_skb(): this patch doesn't touch it
because the function is never called. It seems its support is
incomplete/in progress. The function was added by commit 0507ef8a03
("igc: Add transmit and receive fastpath and interrupt handlers") but
ring_uses_build_skb() always return False since the IGC_RING_FLAG_RX_
BUILD_SKB_ENABLED isn't set anywhere in the driver code.
This patch has been tested with the sample app "xdp1" located in
samples/bpf/ dir.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor the Rx timestamp handling in preparation to land
XDP support.
Rx timestamps are put in the Rx buffer by hardware, before the packet
data. When creating the xdp buffer, we will need to check the Rx
descriptor to determine if the buffer contains timestamp information
and consider the offset when setting xdp.data.
The Rx descriptor check is already done in igc_construct_skb(). To
avoid code duplication, this patch moves the timestamp handling to
igc_clean_rx_irq() so both skb and xdp paths can reuse it.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The RX frame truesize calculation is scattered throughout the RX code.
This patch creates the helper function igc_get_rx_frame_truesize() and
uses it where applicable.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igc driver implements the same page recycling scheme from other
Intel drivers which reuses the page by flipping the buffer. The code
to handle buffer flips is duplicated in many locations so introduce
the igc_rx_buffer_flip() helper and use it where applicable.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The 'skb' argument from igc_tx_cmd_type() is not used so remove it.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vedang Patel <vedang.patel@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the following coccicheck warnings:
./drivers/net/ethernet/intel/igc/igc_main.c:4961:2-14: WARNING:
Assignment of 0/1 to bool variable.
./drivers/net/ethernet/intel/igc/igc_main.c:4955:2-14: WARNING:
Assignment of 0/1 to bool variable.
./drivers/net/ethernet/intel/igc/igc_main.c:4933:1-13: WARNING:
Assignment of 0/1 to bool variable.
./drivers/net/ethernet/intel/igc/igc_main.c:4592:1-24: WARNING:
Assignment of 0/1 to bool variable.
./drivers/net/ethernet/intel/igc/igc_main.c:4438:2-25: WARNING:
Assignment of 0/1 to bool variable.
./drivers/net/ethernet/intel/igc/igc_main.c:4396:2-25: WARNING:
Assignment of 0/1 to bool variable.
./drivers/net/ethernet/intel/igc/igc_main.c:4018:2-25: WARNING:
Assignment of 0/1 to bool variable.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This commit applies to the igc_reset_task the same changes that
were applied to the igb driver in commit 024a8168b7 ("igb:
reinit_locked() should be called with rtnl_lock")
and fix possible race in reset subtask.
Fixes: 0507ef8a03 ("igc: Add transmit and receive fastpath and interrupt handlers")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As explained in commit 29d98f54a4 ("net: enetc: allow hardware
timestamping on TX queues with tc-etf enabled"), hardware TX
timestamping requires an skb with skb->tstamp = 0. When a packet is sent
with SO_TXTIME, the skb->skb_mstamp_ns corrupts the value of skb->tstamp,
so the drivers need to explicitly reset skb->tstamp to zero after
consuming the TX time.
Create a helper named skb_txtime_consumed() which does just that. All
drivers which offload TC_SETUP_QDISC_ETF should implement it, and it
would make it easier to assess during review whether they do the right
thing in order to be compatible with hardware timestamping or not.
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-02-03
This series contains updates to igc, igb, e1000e, and e1000 drivers.
Sasha adds counting of good transmit packets and reporting of NVM version
and gPHY version in ethtool firmware version. Replaces the use of strlcpy
to the preferred strscpy. Fixes a typo that caused the wrong register to be
output. He also removes an unused function pointer, some unneeded defines,
and a non-applicable comment. All changes for igc.
Gal Hammer fixes a typo which caused the RDBAL register values to be
shown instead of TDBAL for igb.
Nick Lowe enables RSS support for i211 devices for igb.
Tom Rix fixes checkpatch warning by removing h from printk format
specifier for igb.
Kaixu Xia removes setting of a variable that is overwritten before next
use for e1000e.
Sudip Mukherjee removes an unneeded assignment for e1000.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
e1000: drop unneeded assignment in e1000_set_itr()
e1000e: remove the redundant value assignment in e1000_update_nvm_checksum_spt
igb: remove h from printk format specifier
igb: Enable RSS for Intel I211 Ethernet Controller
igb: fix TDBAL register show incorrect value
igc: Fix TDBAL register show incorrect value
igc: Remove unused FUNC_1 mask
igc: Remove unused local receiver mask
igc: Prefer strscpy over strlcpy
igc: Expose the gPHY firmware version
igc: Expose the NVM version
igc: Add Host Good Packets Transmitted Count
igc: Remove MULR mask define
igc: Remove igc_set_fw_version comment
igc: Clean up nvm_operations structure
====================
Link: https://lore.kernel.org/r/20210204004259.3662059-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely() checks
are omitted since it's already present in this helper.
Also update some comments near the call sites.
Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This counter counts the number of good (non-erred) packets
transmitted sent by the host.
A good transmit packet is considered one that is 64 or more bytes
in length (from <Destination Address> through <CRC>,
inclusively) in length
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Using skb_csum_is_sctp is a easier way to validate it's a SCTP CRC
checksum offload packet, and yet it also makes igc support SCTP
CRC checksum offload for UDP and GRE encapped packets, just as it
does in igb driver.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add new device ID for the next step of the silicon and
reflect the I226_K part.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'igc_update_stats()' was not updating 'netdev->stats', so the returned
statistics, for example, requested by:
$ ip -s link show dev enp3s0
were not being updated and were always zero.
Fix by returning a set of statistics that are actually being
updated (adapter->stats64).
Fixes: c9a11c23ce ("igc: Add netdev")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
In this case the checks cover only parts of the contexts in which these
functions cannot be called. They fail to detect preemption or interrupt
disabled invocations.
As the functions which are invoked from the various places contain already
a broad variety of checks (always enabled or debug option dependent) cover
all invalid conditions already, there is no point in having inconsistent
warnings in those drivers.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we set the BASET registers of i225 with a base_time in the
future, i225 will "hold" all packets until that base_time is reached,
causing a lot of TX Hangs.
As this behaviour seems contrary to the expectations of the IEEE
802.1Q standard (section 8.6.9, especially 8.6.9.4.5), let's start by
rejecting these types of schedules. If this is too limiting, we can
for example, setup a timer to configure the BASET registers closer to
the start time, only blocking the packets for a "short" while.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Many TSN features depend on the internal PTP clock, so the internal
PTP jumping when the adapter is reset can cause problems, usually in
the form of "TX Hangs" warnings in the driver.
The solution is to save the PTP time before a reset and restore it
after the reset is done. The value of the PTP time is saved before a
reset and we use the difference from CLOCK_MONOTONIC from reset time
to now, to correct what's going to be the new PTP time.
This is heavily inspired by commit bf4bf09bdd ("i40e: save PTP time
before a device reset").
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Completion to commit 900d1e8b34 ("igc: Add LPI counters")
LPI counters exposed by statistics update method.
A EEE TX LPI counter reflect the transmitter entries EEE (IEEE 802.3az)
into the LPI state. A EEE RX LPI counter reflect the receiver link
partner entries into EEE(IEEE 802.3az) LPI state.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 advanced receive descriptor doesn't have the following extend error
bits: CE, SE, SEQ, CXE. In addition to that, the bit TCPE is called L4E
in the datasheet.
Clean up the code accordingly, and get rid of the macro
IGC_RXDEXT_ERR_FRAME_ERR_MASK since it doesn't make much sense anymore.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new device ID's for the next step of the silicon and
reflect i221 and i226 parts
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This takes care of all of the trivial W=1 fixes in the Intel
Ethernet drivers, which allows developers and maintainers to
build more of the networking tree with more complete warning
checks.
There are three classes of kdoc warnings fixed:
- cannot understand function prototype: 'x'
- Excess function parameter 'x' description in 'y'
- Function parameter or member 'x' not described in 'y'
All of the changes were trivial comment updates on
function headers.
Inspired by Lee Jones' series of wireless work to do the same.
Compile tested only, and passes simple test of
$ git ls-files *.[ch] | egrep drivers/net/ethernet/intel | \
xargs scripts/kernel-doc -none
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many device drivers use the same prefetch code structure to
deal with small L1 cacheline size.
Take this code into a function and call it from the drivers.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ictxptc, ictxatc, cbtmpc, cbrdpc, cbrmpc and htcbdpc fields from
the hw_stats structure. Accordance to the i225 device
specification these fields not in use.
This patch come to clean up the driver code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
IGC_ICTXPTC and IGC_ICTXATC are already defined elsewhere, remove this
double definition. Also, remove unneeded registers as they are not
applicable to i225 devices.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tx Queue Min Threshold Count register no applicable for the i225 device.
This patch comes to clean up it.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Though we are populating and tracking ictxqec, the value is not being used
for anything so remove it altogether and save the register read.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Convert all the remaining 'fall through" code comments to the newer
'fallthrough;' keyword.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
PHY of the i225 device support only copper mode.
There is no point to check media type in the
igc_power_up_link() method.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the implementation of igc_power_down_link()
method was just calling igc_power_down_phy_copper_base()
method.
We can just call igc_power_down_phy_copper_base()
method directly.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
TCP segmentation TX context fail counter is not
applicable for i225 devices.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown<aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Differently from I210, I225 doesn't report Rx timestamps via the TS bit
Rx descriptor + RXSTMPL/RXSTMPH registers mechanism. Rx timestamps are
reported in the packet buffer only, which is implemented by igc_ptp_rx_
pktstamp(). So this patch removes igc_ptp_rx_rgtstamp() and all code
related to it, copied from igb driver.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IEEE802.3az-2010 Energy Efficient Ethernet has been
approved as standard (September 2010) and the driver
can enable and disable it via ethtool.
Disable the feature by default on parts which support it.
Add enable/disable eee options.
tx-lpi, tx-timer and advertise not supported yet.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.
For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.
What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Accordance to the i225 datasheet sequence error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
