This makes the code consistent with the recent sc to ab rename.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware expects all the required REO destination rings setup
while processing wmi_init command. Not doing this causes connected
stations getting disconnected and not able to connect back.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is to prepare REO ring setup before sending wmi_init command.
Firmware expects all the required REO rings to be setup while processing
wmi_init command. But as per the current initialization sequence, REO ring
configurations are done only after wmi_init command is sent.
Also refactoring ath11k_mac_create() into ath11k_mac_alloc() and
ath11k_mac_register() to it mac80211 hw structure available before sending
wmi_init command.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
qmi firmware ready event start to initialize the core modules and
the sequence executed with mutex lock. In case of any failure
mutex should be unlocked otherwise it will hang during the recovery.
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first
supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k
uses mac80211 and supports AP, Station and Mesh modes.
Even though ath11k has some similar code as with ath10k (especially
the WMI layer) it was concluded to be simpler to have a "clean start"
for ath11k code base and not try to share the code with ath10k. This
makes maintenance easier and avoids major changes in ath10k, which
would have significantly increased the risk of regressions in existing
setups.
Even though the driver is very similar with ath10k but there are major
differences as well. The datapath is completely different. ath11k
supports multiple MACs, called "soc" in the firmware interface. And
there's only one WMI interface to support.
Currently ath11k supports only IEEE 802.11ac mode, but patches for
802.11ax are available and they will be submitted after ath11k is
accepted to upstream.
The firmware images are available from ath11k-firmware repository but
they will be also submitted to linux-firmware:
https://github.com/kvalo/ath11k-firmware
This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1.
The driver has had multiple authors who are listed in alphabetical
order below.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
