During bcmgenet_put_tx_csum() make sure we differentiate a SKB
headroom re-allocation failure from the normal swap and replace
path.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can turn on the RX/TX checksum offloads and the scatter/gather
features by default and make sure that those are properly reflected
back to e.g: stacked devices such as VLAN.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver resume and open, the HW may have lost its context/state,
utilize bcmgenet_set_features() to make sure we do restore the correct
set of features that were previously configured.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally enabling TX and RX checksum
offloads, refactor bcmgenet_set_features() a bit such that
__netdev_update_features() during register_netdev() can make sure
that features are correctly programmed during network device
registration.
Since we can now be called during register_netdev() with clocks
gated, we need to temporarily turn them on/off in order to have a
successful register programming.
We also move the CRC forward setting read into
bcmgenet_set_features() since priv->crc_fwd_en matters while
turning on RX checksum offload, that way we are guaranteed they
are in sync in case we ever add support for NETIF_F_RXFCS at some
point in the future.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit updates the Rx checksum offload behavior of the driver
to use the more generic CHECKSUM_COMPLETE method that supports all
protocols over the CHECKSUM_UNNECESSARY method that only applies
to some protocols known by the hardware.
This behavior is perceived to be superior.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GENET hardware should be capable of generating IP checksums
using the NETIF_F_HW_CSUM feature, so switch to using that feature
instead of the depricated NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit configures the DMA masks for the GENET driver and
sets the NETIF_F_HIGHDMA flag to report support of the feature.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYSTEMPORT is capabable of doing up to 40-bit of physical addresses, set
an appropriate DMA mask to permit that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver doesn't calculate total number of PFs configured on a
given engine correctly which messed up resources in the PFs
loaded on that engine, leading driver to exceed configuration
of resources (like vlan filters etc.) beyond the limit per
engine, which ended up with asserts from the firmware.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Parity error from the hardware will cause PF to lose the state
of their VFs due to PF's internal reload and hardware reset following
the parity error. Restrict any configuration request from the VFs after
the parity as it could cause unexpected hardware behavior, only way
for VFs to recover would be to trigger FLR on VFs and reload them.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
After executing "ethtool -C eth0 rx-usecs-irq 0", the box becomes
unresponsive, likely due to interrupt livelock. It appears that
a minimum clamp value for the irq timer is computed, but is never
applied.
Fix by applying the corrected clamp value.
Fixes: 74706afa71 ("bnxt_en: Update interrupt coalescing logic.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The VF driver also needs to create the health reporters since
VFs are also involved in firmware reset and recovery. Modify
bnxt_dl_register() and bnxt_dl_unregister() so that they can
be called by the VFs to register/unregister devlink. Only the PF
will register the devlink parameters. With devlink registered,
we can now create the health reporters on the VFs.
Fixes: 6763c779c2 ("bnxt_en: Add new FW devlink_health_reporter")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the logic to properly check the fw capabilities and create the
devlink health reporters only when needed. The current code creates
the reporters unconditionally as long as bp->fw_health is valid, and
that's not correct.
Call bnxt_dl_fw_reporters_create() directly from the init and reset
code path instead of from bnxt_dl_register(). This allows the
reporters to be adjusted when capabilities change. The same
applies to bnxt_dl_fw_reporters_destroy().
Fixes: 6763c779c2 ("bnxt_en: Add new FW devlink_health_reporter")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After fixing the allocation of bp->fw_health in the previous patch,
the driver will not go through the fw reset and recovery code paths
if bp->fw_health allocation fails. So we can now remove the
unnecessary NULL checks.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bp->fw_health needs to be allocated for either the firmware initiated
reset feature or the driver initiated error recovery feature. The
current code is not allocating bp->fw_health for all the necessary cases.
This patch corrects the logic to allocate bp->fw_health correctly when
needed. If allocation fails, we clear the feature flags.
We also add the the missing kfree(bp->fw_health) when the driver is
unloaded. If we get an async reset message from the firmware, we also
need to make sure that we have a valid bp->fw_health before proceeding.
Fixes: 07f83d72d2 ("bnxt_en: Discover firmware error recovery capabilities.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If any change happened in the configuration of VF in VM while
collecting live dump, there could be a race and firmware can return
more data than allocated dump length. Fix it by keeping track of
the accumulated core dump length copied so far and abort the copy
with error code if the next chunk of core dump will exceed the
original dump length.
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will trigger new context memory to be rediscovered and allocated
during the re-probe process after a firmware reset. Without this, the
newly reset firmware does not have valid context memory and the driver
will eventually fail to allocate some resources.
Fixes: ec5d31e3c1 ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic needs to check both bp->total_irqs and the reserved IRQs in
hw_resc->resv_irqs if applicable and see if both are enough to cover
the L2 and RDMA requested vectors. The current code is only checking
bp->total_irqs and can fail in some code paths, such as the TX timeout
code path with the RDMA driver requesting vectors after recovery. In
this code path, we have not reserved enough MSIX resources for the
RDMA driver yet.
Fixes: 75720e6323 ("bnxt_en: Keep track of reserved IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the same bnxt_flash_package_from_file() function to support
devlink flash operation.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Currently, the driver does not allow PHY settings on a multi-function or
NPAR NIC whose port is shared by more than one function. Newer
firmware now allows PHY settings on some of these NICs. Check for
this new firmware setting and allow the user to set the PHY settings
accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If the link settings have been changed by another function sharing the
port, firmware will send us an async. message. In response, we will
call the new bnxt_init_ethtool_link_settings() function to update
the current settings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Refactor this logic in bnxt_probe_phy() into a separate function
bnxt_init_ethtool_link_settings(). It used to be that the settable
link settings will never be changed without going through ethtool.
So we only needed to do this once in bnxt_probe_phy(). Now, another
function sharing the port may change it and we may need to re-initialize
the ethtool settings again in run-time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
New firmware allows PHY loopback to be set without disabling autoneg
first. Check this capability and skip disabling autoneg when
it is supported by firmware. Using this scheme, loopback will
always work even if the PHY only supports autoneg.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The driver currently only assignes 1 RSS context to each VF. This works
for the Linux VF driver. But other drivers, such as DPDK, can make use
of additional RSS contexts. Modify the code to divide up and assign
RSS contexts to VFs just like other resources.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Some chips that need host context memory as a backing store requires
the memory to be initialized to a non-zero value. Query the
value from firmware and initialize the context memory accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Driver calls HWRM_FUNC_RESET firmware call while resuming the device
which clears the context memory backing store. Because of which
allocating firmware resources would eventually fail. Fix it by freeing
all context memory during suspend and reallocate the memory during resume.
Call bnxt_hwrm_queue_qportcfg() in resume path. This firmware call
is needed on the 57500 chips so that firmware will set up the proper
queue mapping in relation to the context memory.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
After driver unregister, firmware is erasing the information that
driver supports new resource management. Send FUNC_RESOURCE_QCAPS
command to inform the firmware that driver supports new resource
management while resuming from hibernation. Otherwise, we fallback
to the older resource allocation scheme.
Also, move driver register after sending FUNC_RESOURCE_QCAPS command
to be consistent with the normal initialization sequence.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Everytime driver registers with firmware, driver is required to
register for async event notifications as well. These 2 calls
are done using the same firmware command and can be combined.
We are also missing the 2nd step to register for async events
in the suspend/resume path and this will fix it. Prior to this,
we were getting only default notifications.
ULP can register for additional async events for the RDMA driver,
so we add a parameter to the new function to only do step 2 when
it is called from ULP.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
In the bnxt_init_one() failure path, if the driver has already called
firmware to register the driver, it is not undoing the driver
registration. Add this missing step to unregister for correctness,
so that the firmware knows that the driver has unloaded.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Disable Bus master during suspend to prevent DMAs after the device
goes into D3hot state. The new 57500 devices may continue to DMA
from context memory after the system goes into D3hot state. This
may cause some PCIe errors on some system. Re-enable it during resume.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Fix BNXT_CHIP_NUM_5645X() to include 57452 and 56454 chip IDs, so
that these chips will be properly classified as P4 chips to take
advantage of the P4 fixes and features.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-11-20
The following pull-request contains BPF updates for your *net-next* tree.
We've added 81 non-merge commits during the last 17 day(s) which contain
a total of 120 files changed, 4958 insertions(+), 1081 deletions(-).
There are 3 trivial conflicts, resolve it by always taking the chunk from
196e8ca748:
<<<<<<< HEAD
=======
void *bpf_map_area_mmapable_alloc(u64 size, int numa_node);
>>>>>>> 196e8ca748
<<<<<<< HEAD
void *bpf_map_area_alloc(u64 size, int numa_node)
=======
static void *__bpf_map_area_alloc(u64 size, int numa_node, bool mmapable)
>>>>>>> 196e8ca748
<<<<<<< HEAD
if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
=======
/* kmalloc()'ed memory can't be mmap()'ed */
if (!mmapable && size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
>>>>>>> 196e8ca748
The main changes are:
1) Addition of BPF trampoline which works as a bridge between kernel functions,
BPF programs and other BPF programs along with two new use cases: i) fentry/fexit
BPF programs for tracing with practically zero overhead to call into BPF (as
opposed to k[ret]probes) and ii) attachment of the former to networking related
programs to see input/output of networking programs (covering xdpdump use case),
from Alexei Starovoitov.
2) BPF array map mmap support and use in libbpf for global data maps; also a big
batch of libbpf improvements, among others, support for reading bitfields in a
relocatable manner (via libbpf's CO-RE helper API), from Andrii Nakryiko.
3) Extend s390x JIT with usage of relative long jumps and loads in order to lift
the current 64/512k size limits on JITed BPF programs there, from Ilya Leoshkevich.
4) Add BPF audit support and emit messages upon successful prog load and unload in
order to have a timeline of events, from Daniel Borkmann and Jiri Olsa.
5) Extension to libbpf and xdpsock sample programs to demo the shared umem mode
(XDP_SHARED_UMEM) as well as RX-only and TX-only sockets, from Magnus Karlsson.
6) Several follow-up bug fixes for libbpf's auto-pinning code and a new API
call named bpf_get_link_xdp_info() for retrieving the full set of prog
IDs attached to XDP, from Toke Høiland-Jørgensen.
7) Add BTF support for array of int, array of struct and multidimensional arrays
and enable it for skb->cb[] access in kfree_skb test, from Martin KaFai Lau.
8) Fix AF_XDP by using the correct number of channels from ethtool, from Luigi Rizzo.
9) Two fixes for BPF selftest to get rid of a hang in test_tc_tunnel and to avoid
xdping to be run as standalone, from Jiri Benc.
10) Various BPF selftest fixes when run with latest LLVM trunk, from Yonghong Song.
11) Fix a memory leak in BPF fentry test run data, from Colin Ian King.
12) Various smaller misc cleanups and improvements mostly all over BPF selftests and
samples, from Daniel T. Lee, Andre Guedes, Anders Roxell, Mao Wenan, Yue Haibing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is especially beneficial during the NVRAM related firmware
commands that have longer timeouts. If the BNXT_STATE_FW_FATAL_COND
flag gets set while waiting for firmware response, abort and return
error.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During loss of heartbeat, log this warning message.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NVM params that are not supported in the current NVM
configuration, return the error as -EOPNOTSUPP.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report health status update to devlink health reporter, once
reset is completed.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux driver is capable of being the master function to handle
resets, so we set the flag to let firmware know. Some other
drivers, such as DPDK, is not capable and will not set the flag.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware supports hot reset, extend ETHTOOL_RESET to support
hot reset driver which does not require a driver reload after
ETHTOOL_RESET. The driver will go through the same coordinated
reset sequence as a firmware initiated fatal/non-fatal reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the larger HWRM_COREDUMP_TIMEOUT value for coredump related
data response from the firmware. These commands take longer than
normal commands.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardware reports RX buffer errors, the latest 57500 chips do not
require reset. The packet is discarded by the hardware and the
ring will continue to operate.
Also, add an rx_buf_errors counter for this type of error. It can help
the user to identify if the aggregation ring is too small.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The aRFS ring table interface has changed for the 57500 chips. Updating
it accordingly so it will work with the latest production firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to bpf_map's refcnt/usercnt, convert bpf_prog's refcnt to atomic64
and remove artificial 32k limit. This allows to make bpf_prog's refcounting
non-failing, simplifying logic of users of bpf_prog_add/bpf_prog_inc.
Validated compilation by running allyesconfig kernel build.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191117172806.2195367-3-andriin@fb.com
All .rw_reset callbacks except bnx2x_84833_hw_reset_phy() use a
void return type. No callers of .hw_reset check a return value and
bnx2x_84833_hw_reset_phy() unconditionally returns 0. Remove all
hw_reset_t casts and fix the return type to void.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return values for format_fw_ver_t callbacks are supposed to be
"int", not "u8". Ultimately, the top-level caller doesn't actually check
the return value at all, but just clean this all up anyway and fix the
prototypes so that casts are no longer needed.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No callers of .config_init check return values. Remove the casting and
change all callbacks to have the correct function prototype.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function casts for .read_status callbacks end up casting some int
return values to u8. This seems to be bug-prone (-EINVAL being returned
into something that appears to be true/false), but fixing the function
prototypes doesn't change the existing behavior. Fix the return values
to remove the casts.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NULL is already "void *" so it will auto-cast in assignments and
initializers. Additionally, all the callbacks for .link_reset,
.config_loopback, .set_link_led, and .phy_specific_func are already
correct. No casting is needed for these, so remove them.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 823eb2a3c4 ("PTP: add support for one-shot output") introduced
a new flag for the PTP periodic output request ioctl. This flag is not
currently supported by any driver.
Fix all drivers which implement the periodic output request ioctl to
explicitly reject any request with flags they do not understand. This
ensures that the driver does not accidentally misinterpret the
PTP_PEROUT_ONE_SHOT flag, or any new flag introduced in the future.
This is important for forward compatibility: if a new flag is
introduced, the driver should reject requests to enable the flag until
the driver has actually been modified to support the flag in question.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christopher Hall <christopher.s.hall@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the array overrun while keeping the eth_addr and eth_addr_mask
pointers as u16 to avoid unaligned u16 access. These were overlooked
when modifying the code to use u16 pointer for proper alignment.
Fixes: 90f906243b ("bnxt_en: Add support for L2 rewrite")
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the missing support for the PHY mode RGMII_RXID.
It's necessary for the Raspberry Pi 4.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register access in bcmgenet_mii_config() is a little bit opaque and
not easy to extend. In preparation for the missing RGMII PHY modes
move all the phy name assignments into the switch statement and the
register access to the end of the function. This make the code easier
to read and extend.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM2711 needs a different maximum DMA burst length. If not set
accordingly a timeout in the transmit queue happens and no package
can be sent. So use the new compatible to derive this value.
Until now the GENET HW version was used as the platform identifier.
This doesn't work with SoC-specific modifications, so introduce a proper
platform data structure.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the error handling for the mandatory IRQs. There is no need
for the error message anymore, this is now handled by platform_get_irq.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As platform_get_irq() now prints an error when the interrupt does not
exist, we are getting a confusing error message in case the optional
WOL IRQ is not defined:
bcmgenet fd58000.ethernet: IRQ index 2 not found
Fix this by using the platform_get_irq_optional().
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_init_hw() function may reset the PHY to a configuration
that does not match manual network settings stored in the phydev
structure. If the phy state machine is polled rather than event
driven this can create a timing hazard where the phy state machine
might alter the settings stored in the phydev structure from the
value read from the BMCR.
This commit follows invocations of phy_init_hw() by the bcmgenet
driver with invocations of the genphy_config_aneg() function to
ensure that the BMCR is written to match the settings held in the
phydev structure. This prevents the risk of manual settings being
accidentally altered.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1f51548627.
This commit improved the chances of the umac resetting cleanly by
ensuring that the PHY was restored to its normal operation prior
to resetting the umac. However, there were still cases when the
PHY might not be driving a Tx clock to the umac during this window
(e.g. when the PHY detects no link).
The previous commit now ensures that the unimac receives clocks
from the MAC during its reset window so this commit is no longer
needed. This commit also has an unintended negative impact on the
MDIO performance of the UniMAC MDIO interface because it is used
before the MDIO interrupts are reenabled, so it should be removed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted in commit 28c2d1a7a0 ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked while sw_reset
is asserted for its state machines to reset cleanly.
The transmit and receive clocks used by the UniMAC are derived from
the signals used on its PHY interface. The bcmgenet MAC can be
configured to work with different PHY interfaces including MII,
GMII, RGMII, and Reverse MII on internal and external interfaces.
Unfortunately for the UniMAC, when configured for MII the Tx clock
is always driven from the PHY which places it outside of the direct
control of the MAC.
The earlier commit enabled a local loopback mode within the UniMAC
so that the receive clock would be derived from the transmit clock
which addressed the observed issue with an external GPHY disabling
it's Rx clock. However, when a Tx clock is not available this
loopback is insufficient.
This commit implements a workaround that leverages the fact that
the MAC can reliably generate all of its necessary clocking by
enterring the external GPHY RGMII interface mode with the UniMAC in
local loopback during the sw_reset interval. Unfortunately, this
has the undesirable side efect of the RGMII GTXCLK signal being
driven during the same window.
In most configurations this is a benign side effect as the signal
is either not routed to a pin or is already expected to drive the
pin. The one exception is when an external MII PHY is expected to
drive the same pin with its TX_CLK output creating output driver
contention.
This commit exploits the IEEE 802.3 clause 22 standard defined
isolate mode to force an external MII PHY to present a high
impedance on its TX_CLK output during the window to prevent any
contention at the pin.
The MII interface is used internally with the 40nm internal EPHY
which agressively disables its clocks for power savings leading to
incomplete resets of the UniMAC and many instabilities observed
over the years. The workaround of this commit is expected to put
an end to those problems.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new FW has added extra validation for HSI version to
make FW backward compatible with older VF drivers. Hence
set fp_hsi_ver to Fast Path HSI version of the FW in use.
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF driver doesn't enable tx-switching for all cos queues/clients,
which causes packets drop from PF to VF. Fix this by enabling
tx-switching on all cos queues/clients.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW version 7.13.15 addresses the issue in Multi-cos implementation.
This patch re-enables the Multi-Cos support in the driver.
Fixes: d1f0b5dce8 ("bnx2x: Disable multi-cos feature.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 97a27d6d6e8d "bnx2x: Add FW 7.13.15.0" added said .bin FW to
linux-firmware tree. This FW addresses few important issues in the earlier
FW release.
This patch incorporates FW 7.13.15.0 in the bnx2x driver.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Inform the RDMA driver to stop/start during suspend/resume. The
RDMA driver needs to stop and start just like error recovery.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Notify the RDMA driver by calling the bnxt_ulp_stop()/bnxt_ulp_start()
hooks during error recovery. The current ULP IRQ start/stop
sequence in error recovery (which is insufficient) is replaced with the
full reset sequence when we call bnxt_ulp_stop()/bnxt_ulp_start().
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We call bnxt_ulp_stop() to notify the RDMA driver that some error or
imminent reset is about to happen. After that we always call
some variants of bnxt_close().
In the next patch, we will integrate the recently added error
recovery with the RDMA driver. In response to ulp_stop, the
RDMA driver may free MSIX vectors and that will also trigger
bnxt_close(). To avoid bnxt_close() from being called twice,
we set a new flag after ulp_stop is called. If the RDMA driver
frees MSIX vectors while the new flag is set, we will not call
bnxt_close(), knowing that it will happen in due course.
With this change, we must make sure that the bnxt_close() call
after ulp_stop will reset IRQ. Modify bnxt_reset_task()
accordingly if we call ulp_stop.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decap (VXLAN tunnel) flow rules are not getting offloaded with
upstream kernel. This is because TC block callback infrastructure has
been updated to use indirect callbacks to get offloaded rules from
other higher level devices (such as tunnels), instead of ndo_setup_tc().
Since the decap rules are applied to the tunnel devices (e.g, vxlan_sys),
the driver should register for indirect TC callback with tunnel devices
to get the rules for offloading. This patch updates the driver to
register and process indirect TC block callbacks from VXLAN tunnels.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provides support for modifying L3/L4 Header parameters to support NAT.
Sets the appropriate fields/bits in cfa_flow_alloc cmd.
Sample cmd for offloading an IPv4 flow with SNAT:
ovs-ofctl add-flow ovsbr0 "ip,nw_src=192.168.201.44 \
actions=mod_nw_src:203.31.220.144,output:p7p1"
Replace 'nw_src' with 'nw_dst' in above cmd for DNAT with IPv4
Sample cmd for offloading an IPv4 flow with SNAPT:
ovs-ofctl add-flow ovsbr0 "ip,nw_src=192.168.201.44 \
actions=mod_nw_src:203.31.220.144, mod_tp_src:6789,output:p7p1"
Similar to DNAT, replace 'tp_src' with 'tp_dst' for offloading flow
with DNAPT
Sample cmd for offloading an IPv6 flow with SNAT:
ovs-ofctl add-flow ovsbr0 "ipv6, ipv6_src=2001:5c0:9168::2/64 \
actions=load:0x1->NXM_NX_IPV6_SRC[0..63], \
load:0x20010db801920000->NXM_NX_IPV6_SRC[64..127],output:p7p1"
Replace 'SRC' with DST' above for IPv6 DNAT
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For every single case where bnxt_tc_can_offload() can fail, we are
logging a user friendly descriptive message anyway, but because of the
path it would take in case of failure, another redundant error message
would get logged. Just freeing the node and returning from the point of
failure should suffice.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for packet edit offload of L2 fields (src mac &
dst mac, also referred as L2 rewrite). Only when the mask is fully exact
match for a field, the command is sent down to the adapter to offload
such a flow. Otherwise, an error is returned.
v2: Fix pointer alignment issue in bnxt_fill_l2_rewrite_fields() [MChan]
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver supports 2 types of core dumps.
1. Live dump - Firmware dump when system is up and running.
2. Crash dump - Dump which is collected during firmware crash
that can be retrieved after recovery.
Crash dump is currently supported only on specific 58800 chips
which can be retrieved using OP-TEE API only, as firmware cannot
access this region directly.
User needs to set the dump flag using following command before
initiating the dump collection:
$ ethtool -W|--set-dump eth0 N
Where N is "0" for live dump and "1" for crash dump
Command to collect the dump after setting the flag:
$ ethtool -w eth0 data Filename
v3: Modify set_dump to support even when CONFIG_TEE_BNXT_FW=n.
Also change log message to netdev_info().
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In error recovery process when firmware indicates that it is
completely down, initiate a firmware reset by calling OP-TEE API.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use true/false for bool type in bnxt_timer function.
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recently added error recovery logic, the device may already
be disabled if the firmware recovery is unsuccessful. In
bnxt_remove_one(), check that the device is still enabled first
before calling pci_disable_device().
Fixes: 3bc7d4a352 ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
When firmware indicates that driver needs to invoke firmware reset
which is common for both error recovery and live firmware reset path,
driver needs a different time to wait before polling for firmware
readiness.
Modify the wait time to fw_reset_min_dsecs, which is initialised to
correct timeout for error recovery and firmware reset.
Fixes: 4037eb7156 ("bnxt_en: Add a new BNXT_FW_RESET_STATE_POLL_FW_DOWN state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The current code does not do endian swapping between the devlink
parameter and the internal NVRAM representation. Define a union to
represent the little endian NVRAM data and add 2 helper functions to
copy to and from the NVRAM data with the proper byte swapping.
Fixes: 782a624d00 ("bnxt_en: Add bnxt_en initial port params table and register it")
Cc: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The current code that rounds up the NVRAM parameter bit size to the next
byte size for the devlink parameter is not always correct. The MSIX
devlink parameters are 4 bytes and we don't get the correct size
using this method.
Fix it by adding a new dl_num_bytes member to the bnxt_dl_nvm_param
structure which statically provides bytesize information according
to the devlink parameter type definition.
Fixes: 782a624d00 ("bnxt_en: Add bnxt_en initial port params table and register it")
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The EPHY integrated into the 40nm Set-Top Box devices can falsely
detect energy when connected to a disabled peer interface. When the
peer interface is enabled the EPHY will detect and report the link
as active, but on occasion may get into a state where it is not
able to exchange data with the connected GENET MAC. This issue has
not been observed when the link parameters are auto-negotiated;
however, it has been observed with a manually configured link.
It has been empirically determined that issuing a soft reset to the
EPHY when energy is detected prevents it from getting into this bad
state.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that the "Workaround for putting the PHY in IDDQ mode"
used by the internal EPHYs on 40nm Set-Top Box chips when powering
down puts the interface to the GENET MAC in a state that can cause
subsequent MAC resets to be incomplete.
Rather than restore the forced soft reset when powering up internal
PHYs, this commit moves the invocation of phy_init_hw earlier in
the MAC initialization sequence to just before the MAC reset in the
open and resume functions. This allows the interface to be stable
and allows the MAC resets to be successful.
The bcmgenet_mii_probe() function is split in two to accommodate
this. The new function bcmgenet_mii_connect() handles the first
half of the functionality before the MAC initialization, and the
bcmgenet_mii_config() function is extended to provide the remaining
PHY configuration following the MAC initialization.
Fixes: 484bfa1507 ("Revert "net: bcmgenet: Software reset EPHY after power on"")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When commit 28b2e0d2cd ("net: phy: remove parameter new_link from
phy_mac_interrupt()") removed the new_link parameter it set the
phydev->link state from the MAC before invoking phy_mac_interrupt().
However, once commit 88d6272aca ("net: phy: avoid unneeded MDIO
reads in genphy_read_status") was added this initialization prevents
the proper determination of the connection parameters by the function
genphy_read_status().
This commit removes that initialization to restore the proper
functionality.
Fixes: 88d6272aca ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RGMII_MODE_EN bit value was 0 for GENET versions 1 through 3, and
became 6 for GENET v4 and above, account for that difference.
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that we completely quiesce the network device, including its
DMA to avoid having it continue to receive packets while there is no
software alive to service those.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having a hard failure and stopping the driver's probe
routine, generate a random Ethernet MAC address to keep going.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_VENDOR_BROADCOM is intended to control a kconfig menu only.
It should not have anything to do with code generation.
As such, it should not select DIMLIB for all drivers under
NET_VENDOR_BROADCOM. Instead each driver that needs DIMLIB should
select it (being the symbols SYSTEMPORT, BNXT, and BCMGENET).
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907021810220.13058@ramsan.of.borg/
Fixes: 4f75da3666 ("linux/dim: Move implementation to .c files")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Tal Gilboa <talgi@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: netdev@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phydev->dev_flags is entirely dependent on the PHY device driver which
is going to be used, setting the internal GENET PHY revision in those
bits only makes sense when drivers/net/phy/bcm7xxx.c is the PHY driver
being used.
Fixes: 487320c541 ("net: bcmgenet: communicate integrated PHY revision to PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable reg is being assigned a value that is never read
and is being re-assigned in the following for-loop. The
assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During health reporter operations, driver might want to fill-up
the extack message, so propagate extack down to the health reporter ops.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "priv->phy_interface" variable is an enum and in this context GCC
will treat it as unsigned so the error handling will never be
triggered.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new state is required when firmware indicates that the error
recovery process requires polling for firmware state to be completely
down before initiating reset. For example, firmware may take some
time to collect the crash dump before it is down and ready to be
reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some error recovery updates to the spec., among other minor changes.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware coredump messages take much longer than standard messages,
so increase the timeout accordingly.
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the BNXT_STATE_OPEN flag instead of netif_running() in
bnxt_set_rx_mode(). If the driver is going through any reset, such
as firmware reset or even TX timeout, it may not be ready to set the RX
mode and may crash. The new rx mode settings will be picked up when
the device is opened again later.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change enables the use of SW timestamping on the Raspberry Pi 4.
bcmgenet's transmit function bcmgenet_xmit() implements software
timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE capability was
missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced. By using
ethtool_ops bcmgenet_ethtool_ops() as get_ts_info(), the
SOF_TIMESTAMPING_TX_SOFTWARE capability is announced.
Similar to commit a8f5cb9e79 ("smsc95xx: use ethtool_op_get_ts_info()")
Signed-off-by: Ryan M. Collins <rmc032@bucknell.edu>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function bnxt_get_registered_vfs() to handle the work
of getting the number of registered VFs under #ifdef CONFIG_BNXT_SRIOV.
The main code will call this function and will always work correctly
whether CONFIG_BNXT_SRIOV is set or not.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
